Engineering topics

Stewart, D.

Publications and source records attributed to Stewart, D..

8 records

NASA NTRS2010

Experience with Delay-Tolerant Networking from Orbit

We describe the first use from space of the Bundle Protocol for Delay-Tolerant Networking (DTN) and lessons learned from experiments made and experience gained with this protocol. The Disaster Monitoring Constellation (DMC), constructed by Surrey Satellite Technology Ltd (SSTL), is a multiple-satellite Earth-imaging low-Earth-orbit sensor network in which recorded image swaths are stored onboard each satellite and later downloaded from the satellite payloads to a ground station. Store-and-forward of images with capture and later download gives each satellite the characteristics of a node in a disruption-tolerant network. Originally developed for the Interplanetary Internet, DTNs are now under investigation in an Internet Research Task Force (IRTF) DTN research group (RG), which has developed a bundle architecture and protocol. The DMC is technically advanced in its adoption of the Internet Protocol (IP) for its imaging payloads and for satellite command and control, based around reuse of commercial networking and link protocols. These satellites use of IP has enabled earlier experiments with the Cisco router in Low Earth Orbit (CLEO) onboard the constellation s UK-DMC satellite. Earth images are downloaded from the satellites using a custom IP-based high-speed transfer protocol developed by SSTL, Saratoga, which tolerates unusual link environments. Saratoga has been documented in the Internet Engineering Task Force (IETF) for wider adoption. We experiment with the use of DTNRG bundle concepts onboard the UK-DMC satellite, by examining how Saratoga can be used as a DTN convergence layer to carry the DTNRG Bundle Protocol, so that sensor images can be delivered to ground stations and beyond as bundles. Our practical experience with the first successful use of the DTNRG Bundle Protocol in a space environment gives us insights into the design of the Bundle Protocol and enables us to identify issues that must be addressed before wider deployment of the Bundle Protocol. Published in 2010 by John Wiley & Sons, Ltd. KEY WORDS: Internet; UK-DMC; satellite; Delay-Tolerant Networking (DTN); Bundle Protocol

Ivancic, W.↗

NASA NTRS2006

Processes Influencing Ozone Levels in Alaskan Forest Fires Plumes during Long-Range Transport over the North Atlantic

A case of long-range transport of a biomass burning plume from Alaska to Europe is analyzed using a Lagrangian approach. This plume was sampled several times in the free troposphere over North America, the North Atlantic and Europe by 3 different aircraft during the IGAC Lagrangian 2K4 experiment which was part of the ICARTT/ITOP measurement intensive in summer 2004. Measurements in the plume showed enhanced values of CO, VOCs and NOy, mainly in form of PAN. Observed O3 levels increased by 17 ppbv over 5 days. A photochemical trajectory model, CiTTyCAT, is used to examine processes responsible for the chemical evolution of the plume. The model was initialized with upwind data, and compared with downwind measurements. The influence of high aerosol loading on photolysis rates in the plume is investigated using in-situ aerosol measurements in the plume and lidar retrievals of optical depth as input into a photolysis code (Fast-J), run in the model. Significant impacts on photochemistry are found with a decrease of 18 percent in O3 production and 24 percent in O3 destruction over 5 days when including aerosols. The plume is found to be chemically active with large O3 increases attributed primarily to PAN decomposition during descent of the plume towards Europe. The predicted O3 changes are very dependent on temperature changes during transport, and also, on water vapor levels in the lower troposphere which can lead to O3 destruction. Simulation of mixing/dilution was necessary to reproduce observed pollutants level in the plume. Mixing was simulated using background concentrations from measurements in air masses in close proximity to the plume, and mixing timescales (averaging 6.25 days) were derived from CO changes. Observed and simulated O3/CO correlations in the plume are also compared in order to evaluate the photochemistry in the model. Observed slopes changed from negative to positive over 5 days. This change, which can be attributed largely to photochemistry, is well reproduced by multiple model runs even if slope values are slightly underestimated suggesting small underestimation of photochemical processes. The possible impact of this biomass burning plume on O3 levels in the Europe boundary layer is also examined by running the model for a further 5 days, and comparing with data collected at surface sites, such as Jungfraujoch, which showed small O3 increases and elevated CO levels. The model predicts significant changes in O3 over this 10 days due to photochemistry but the signal is largely lost due to the effects of dilution. However, measurement in several others BB plumes over Europe show that O3 impact of Alaskan fires can be punctually significant over Europe.

Real, E.↗

NASA NTRS1982

RCA SATCOM in-orbit experience: An update

The SATCOM in-orbit battery performance was evaluated. The capacitance and constant current charge rates for each of the three batteries were monitored. A typical eclipse discharge profile was generated and attendant reconditioning recharge conditions were considered. Battery temperatures, pressures, and average battery voltages are presented in tabular form. In-orbit data from monitoring the end of discharge voltage during eclipses, a key performance parameter, are also given.

Stewart, D.↗

NASA NTRS1981

RCA Satcom in-orbit experience

The F1 and F2 spacecraft battery systems are described. Battery reconditioning and discharge are discussed and graphically illustrated. Current sharing as a measure of battery performance is also plotted.

Stewart, D.↗

NASA NTRS1978

Opacified silica reusable surface insulation /RSI/ for thermal protection of the Space Shuttle Orbiter

A reusable surface insulation (RSI) material adopted for use on limited areas of the Orbiter's heat shield is described. The RSI is a rigid sintered fibrous silica material containing about 3% by weight of 1200-grit silicon carbide powder. RSI manufacture is described; strength characteristics and thermal conductivity of the final product can be tailored by controlling the isotropy, and the density, coefficient of thermal expansion, and specific heat are reported. Data establishing that opacification of RSI with silicon carbide lowers the thermal conductivity are presented.

Goldstein, H. E.↗

NASA NTRS1978

Opacified silica reusable surface insulation /RSI/ for thermal protection of the Space Shuttle Orbiter

The present paper deals with a second-generation reusable surface insulation (RSI) material, termed LI-2200, which has been chosen for use on limited areas of the Orbiter heat shield. It is a rigid sintered fibrous silica containing about 3% by weight 1200 grit silicon carbide powder, capable of surviving multiple reentries at temperatures on the order of 1400 C. The lower thermal conductivity achieved by opacification with silicon carbide is demonstrated by radiant transmission measurements and thermal response tests.

Goldstein, H. E.↗

NASA NTRS1974

Radio astronomy Explorer-B postlaunch attitude operations analysis

The attitude support activities of the Radio Astronomy Explorer-B are reported. The performance of the spacecraft hardware and software are discussed along with details of the mission events, from launch through main boom deployment. Reproductions of displays are presented which were used during support activities. The interactive graphics proved the support function by providing the quality control necessary to ensure mission success in an environment where flight simulated ground testing of spacecraft hardware cannot be performed.

Werking, R. D.↗

NASA NTRS1973

Silica Reusable Surface Insulation Improvement Research

Fiber characterization, fabrication processes, physical properties, and thermal responses are investigated to improve silica reusable surface insulation tiles. Criteria for fiber selection on the basis of chemical composition, shrinkage, and devitrification have been defined and a simple process for fabricating silica surface insulation materials has been developed that produces only 5% shrinkage and no devitrification of tiles at 1533 K in ten hours. Anisotropic tile with improved weak direction strength has been fabricated using conventional molding techniques.

Goldstein, H. E.↗