Engineering Papers⌕ Search

Engineering topics

Stevens, G. D.

Publications and source records attributed to Stevens, G. D..

At least 19 records

A diagnostic to measure time-resolved atom column density and Doppler temperature in atomic vapors produced by laser ablation

We report on the development of a diagnostic to measure the time-resolved column density and Doppler temperature of atomic vapors produced by laser ablation. The diagnostic is based on the strong frequency dependence of the atomic susceptibility near an electronic transition in the interrogated atomic species. Interference on the face of a fast photodetector between the several frequency components present in a sinusoidally phase-modulated probe beam will produce a time signature uniquely determined by the column density of atoms in the probed atomic state and the Doppler temperature of the atomic vapor. With the extensive, high precision atomic spectroscopy data available in the literature, it is possible to model the vapor and extract the desired parameters through comparison of the model result with the experimental data.

47 OTHER INSTRUMENTATION↗

Non-Richtmyer–Meshkov instability ejecta production based on shallow bubble collapse

The study of shock-driven ejecta production has focused on Richtmyer–Meshkov instability (RMI) growth from geometric features of the material surface. Extensive study of this mechanism under both single- and multiple-shock conditions has found that the ejected mass tends to be closely associated with the shocked surface phase, and its temperature is not dramatically greater than the hydrodynamic shock temperature of the bulk. In this work, we propose and demonstrate a new ejecta production mechanism that can occur under multiple-shock conditions based on the collapse of bubbles near the free surface of the material. This mechanism produces ejected mass that is much greater in quantity than observed in the RMI case. The particles are much hotter than predicted by the shock Hugoniot state, and the ejected mass does not appear to be strongly dependent upon initial surface finish. The ejecta source extends into the material with no clear remaining free surface. We name this mechanism Shallow Bubble Collapse (SBC) and discuss the conditions under which it activates. We demonstrate resolved modeling methods that enable the calculation, design, and study of SBC as a mechanism and perform a series of experiments to compare with the models. Under some multiple-shock conditions, SBC ejection produces ten times more ejected mass than RMI growth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Atomic Ejecta Source Optical Probe (AESOP) (L3 Milestone Report FY2021 Work Package)

As part of its mission to ensure the reliability of the nation's nuclear weapons stockpile, the NNSA has funded a broad range of projects to characterize the mass of material ejected from shocked metal surfaces with special emphasis placed on determining the size distribution of macroscopic "ejecta" particles. Substantial work has been done for particles with diameters down to roughly 1 μm, but little data is available for smaller particles, and no data exist for the amount of atomic-scale ejecta produced in such dynamic environments. Such data are important due to the implications for weapons systems behavior but also for distinguishing between different potential ejecta production mechanisms, such as Rayleight-Taylor instability or the shallow-bubble-collapse phenomenon recently proposed by G. Maskally.

36 MATERIALS SCIENCE↗

Experimental observations of shock-wave-induced bubble collapse and hot-spot formation in nitromethane liquid explosive

We studied the collapse of individual helium gas bubbles in the homogeneous explosive nitromethane (NM) to investigate effects of hot-spot formation on the detonation process. A bubble was injected into a NM sample, and a shock wave from an explosive detonator compressed the bubble, creating a localized hot spot. We measured shock and detonation wave speeds with optical velocimetry, and we used a high-speed camera to image the shock propagation and the pre- and post-bubble collapse processes. An infrared camera image showed the residual radiance temperature distribution after the bubble collapse, and an optical fiber pyrometer measured the time-resolved thermal radiance. We measured the optical spectra of light emitted from detonating NM without a bubble and from a collapsing bubble in shocked, undetonated NM. We estimated temperatures of the detonation fronts and of the hot spots formed by bubble collapse. To study the incipient detonation process, we performed all bubble collapse experiments at pressures below the threshold for creating a sustained detonation. Where the bubble collapsed, we observed an opaque, thermally emissive region believed to be chemical reaction products. Chemical reactions in NM can be produced with lower shock pressures (~1 GPa) when a helium bubble is present than without a bubble (~10 GPa). We used hydrodynamic modeling to predict shock wave propagation, extent of chemical reaction, and subsequent temperature rise from the collapsing bubble. Simulations using a temperature-dependent Arrhenius burn model gave much better results than reactive burn models that depend only on pressure and density.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermal interfaces in dynamic compression experiments

Temperature is a difficult thermodynamic variable to measure in dynamic compression experiments. Optical pyrometry is a general-purpose technique for measuring temperature from a radiant surface, but that surface is often the interface between distinct materials with temperatures that vary spatially along the loading direction. This leads to a fundamental problem: how does the measured interface temperature relate to this temperature profile along the compression axis? Numerical analysis of loading history and thermal diffusion at these interfaces shows that seemingly subtle changes in experiment geometry can lead to very different temperature profiles. We compare these results to laboratory temperature measurements of shock-compressed tin.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Anisotropic shock response of single-crystalline β-phase tin shock physics, molecular dynamics, plasticity

Mesoscale simulations of the dynamic response of polycrystalline metals to shockwave compression can provide unique insight in to the nature of the various physical mechanisms responsible for material failure. This approach requires a constitutive description for individual grains and boundaries, including defects such as dislocations, within an explicit representation of the microstructure geometry and evolving deformation fields. Computational models of the single-crystal constituents cannot be unambiguously constrained by traditional measurements of the shock or stress-strain response of polycrystalline metals. Instead, these models require comprehensive measurements of the anisotropic shock response of single crystals for their calibration and validation. We present a coordinated experimental and simulation campaign on the shock response of single-crystalline β-phase tin demonstrating a remarkable anisotropic elastic-plastic response of the metal. This anisotropy will be explained with the help of molecular dynamics simulations that show preferred twinning in one orientation.

36 MATERIALS SCIENCE↗

Simultaneous Raman and pyrometric temperature measurements in shock-wave-compressed toluene

We fielded experiments to compare temperatures measured simultaneously by pyrometry and Raman spectroscopy in toluene shocked to 9 GPa. A 0.5 mm thick toluene sample was compressed between sapphire windows by plate impact from a gas gun. As the shock wave reverberated between the windows, the pressure increased stepwise to about 9 GPa. While the sample was near its peak pressure, we measured the Raman spectrum and determined temperature from the ratio of the Stokes and anti-Stokes intensities. Simultaneously, we measured the sample thermal radiance from the C-H vibration bands that occur between 3.2 and 3.6 μm to determine temperature pyrometrically. The pyrometer used a biased indium antimonide detector paired with a custom transimpedance amplifier, a system capable of temperature measurements as low as about 400 K. The Raman measurements gave a temperature of 530 ± 25 K in the bulk volume of toluene. Pyrometry gave a temperature of 496 + 15/-20 K, which is in reasonable agreement with the Raman measurement. Comparisons of this type are necessary to validate pyrometry as a temperature diagnostic in dynamic experiments.

36 MATERIALS SCIENCE↗

Dynamic reflectance changes in high-purity zirconium when it is shocked from the α to ω phase

Flash lamp-illuminated integrating spheres have been used to measure the dynamic reflectance at the interface between a shocked metal target and a window maintaining the shock stress. In conjunction with radiance measurements, this method was recently used to study the pressure versus temperature phase boundary of the beta phase to body-centered-tetragonal transition of tin at around 13 GPa and, in separate experiments, to show a relationship between the reflectance and the phase fraction. We have used this technique to measure the ratio, R, of the dynamic reflectance relative to the ambient value for a high-purity zirconium sample attached to a sapphire window to study the alpha to omega phase transition. Nine experiments cover the range of stress, σ, from 4 to 16 GPa at six wavelengths from 500 to 1550 nm. The two phases in zirconium differ in volume by <1%, so a phase change between them can be difficult to identify from anomalies in the particle velocity measured on the shock Hugoniot. The phase boundary is believed to cross the Hugoniot around 3 GPa, but dynamically it is observed at much higher stresses >6 GPa. Our results show that the relative reflectance decreases upon initial shock in the alpha state but increases as the material transforms to its omega state. The slope dR/dσ changes the sign around the phase transition. For shocks below 6 GPa, dR/dσ < 0, and for σ above 10 GPa, dR/dσ > 0. In the stress region between 6 and 10 GPa, dR/dσ varies somewhat, perhaps due to the band structure or because the transition is incomplete there. I. INTRODUCTION

74 ATOMIC AND MOLECULAR PHYSICS↗

Spall response of single-crystal copper

We performed a series of systematic spall experiments on single-crystal copper in an effort to determine and isolate the effects of crystal orientation, peak stress, and unloading strain rate on the tensile spall strength. Strain rates ranging from 0.62 to 2.2 × 10 6 s -1 and peak shock stresses in the 5–14 GPa range, with one additional experiment near 50 GPa, were explored as part of this work. Gun-driven impactors, called flyer plates, generated flat top shocks followed by spall. This work highlights the effect of crystal anisotropy on the spall strength by showing that the spall strength decreases in the following order: [100], [110], and [111]. Over the range of stresses and strain rates explored, the spall strength of [100] copper depends strongly on both the strain rate and shock stress. Except at the very highest shock stress, the results for the [100] orientation show linear relationships between the spall strength and both the applied compressive stress and the strain rate. In addition, hydrodynamic computer code simulations of the spall experiments were performed to calculate the relationship between the strain rate near the spall plane in the target and the rate of free surface velocity release during the pullback. As expected, strain rates at the spall plane are much higher than the strain rates estimated from the free surface velocity release rate. We have begun soft recovery experiments and molecular dynamics calculations to understand the unusual recompression observed in the spall signature for [100] crystals.

36 MATERIALS SCIENCE↗

Ejected Particle Size Distributions from Shocked Metal Surfaces

Here, we present size distributions for particles ejected from features machined onto the surface of shocked Sn targets. The functional form of the size distributions is assumed to be log-normal, and the characteristic parameters of the distribution are extracted from the measured angular distribution of light scattered from a laser beam incident on the ejected particles. We also found strong evidence for a bimodal distribution of particle sizes with smaller particles evolved from features machined into the target surface and larger particles being produced at the edges of these features.

36 MATERIALS SCIENCE↗

Yield strength of Cu and a CuPb alloy (1% Pb)

With PBX9501 we explosively loaded fully annealed OFHC-Cu and an OFHC-CuPb (extruded with 1% Pb that ag- gregates at the Cu grain boundaries) to study the effects of the 1% Pb on the elastic-plastic yield Y of Cu. The yield-stress Y was studied through observation of surface velocimetry and total ejected mass ρ A from periodic surface perturbations machined onto the sample surfaces. The perturbation’s wavelengths were λ $\approx$ 65 µm, and their amplitudes h were varied to determine the wavenumber (2π/λ) amplitude product kh at which ejecta production for the Cu and CuPb begins, which relates to Y. The Y of the two materials is apparently different.

36 MATERIALS SCIENCE↗

Simultaneous broadband laser ranging and photonic Doppler velocimetry for dynamic compression experiments

A diagnostic was developed to simultaneously measure both the distance and velocity of rapidly moving surfaces in dynamic compression experiments, specifically non-planar experiments where integrating the velocity in one direction does not always give the material position accurately. The diagnostic is constructed mainly from fiber-optic telecommunications components. The distance measurement is based on a technique described by Xia and Zhang [Opt. Express 18, 4118 (2010)], which determines the target distance every 20 ns and is independent of the target speed. We have extended the full range of the diagnostic to several centimeters to allow its use in dynamic experiments, and we multiplexed it with a photonic Doppler velocimetry (PDV) system so that distance and velocity histories can be measured simultaneously using one fiber-optic probe. The diagnostic was demonstrated on a spinning square cylinder to show how integrating a PDV record can give an incorrect surface position and how the ranging diagnostic described here obtains it directly. The diagnostic was also tested on an explosive experiment where copper fragments and surface ejecta were identified in both the distance and velocity signals. We show how the distance measurements complement the velocity data. Potential applications are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal transport in shock wave–compressed solids using pulsed laser heating

A pulsed laser heating method was developed for determining thermal transport properties of solids under shock-wave compression. While the solid is compressed, a laser deposits a known amount of heat onto the sample surface, which is held in the shocked state by a transparent window. The heat from the laser briefly elevates the surface temperature and then diffuses into the interior via one-dimensional heat conduction. The thermal effusivity is determined from the time history of the resulting surface temperature pulse, which is recorded with optical pyrometry. Thermal effusivity is the square root of the product of thermal conductivity and volumetric heat capacity and is the key thermal transport parameter for relating the surface temperature to the interior temperature of the sample in a dynamic compression experiment. Therefore, this method provides information that is needed to determine the thermodynamic state of the interior of a compressed metal sample from a temperature measurement at the surface. The laser heat method was successfully demonstrated on tin that was shock compressed with explosives to a stress and temperature of ∼25 GPa and ∼1300 K. In this state, tin was observed to have a thermal effusivity of close to twice its ambient value. The implications on determining the interior shock wave temperature of tin are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Ejecta Particle-Size Measurements in Vacuum and Helium Gas using Ultraviolet In-Line Fraunhofer Holography

An Ultraviolet (UV) in-line Fraunhofer holography diagnostic has been developed for making high-resolution spatial measurements of ejecta particles traveling at many mm/μsec. This report will discuss the development of the diagnostic including the high-powered laser system and high-resolution optical relay system. In addition, the system required to reconstruct the images from the hologram and the corresponding analysis of those images to extract particles will also be described. Finally, results from six high-explosive (HE), shock-driven Sn ejecta experiments will be presented. Particle size distributions will be shown that cover most of the ejecta velocities for experiments conducted in a vacuum, and helium gas environments. In addition, a modification has been made to the laser system that produces two laser pulses separated by 6.8 ns. This double-pulsed capability allows a superposition of two holograms to be acquired at two different times, thus allowing ejecta velocities to be measured directly. Results from this double pulsed experiment will be described.

36 MATERIALS SCIENCE↗

High Pressure Sensing and Dynamics Using High Speed Fiber Bragg Grating Interrogation Systems

Fiber Bragg gratings (FBGs) are developing into useful sensing tools for measuring high pressure dynamics in extreme environments under shock loading conditions. Approaches using traditional diode array coupled FBG interrogation systems are often limited to readout speeds in the sub-MHz range. For shock wave physics, required detection speeds approaching 100 MHz are desired. We explore the use of two types of FBG sensing systems that are aimed at applying this technology as embedded high pressure probes for transient shock events. Both approaches measure time resolved spectral shifts in the return light from short (few mm long) uniform FBGs at 1550 nm. In the first approach, we use a fiber coupled spectrometer to demultiplex spectral channels into an array (up to 12) of single element InGaAs photoreceivers. By monitoring the detectors during a shock impact event with high speed recording, we are able to track the pressure induced spectral shifting in FBG down to a time resolution of 20 ns. In the second approach, developed at the Special Technologies Lab, a coherent mode-locked fiber laser is used to illuminate the FBG sensor. After the sensor, wavelength-to-time mapping is accomplished with a chromatic dispersive element, and entire spectra are sampled using a single detector at the modelocked laser repetition rate of 50 MHz. By sampling with a 12 GHz InGaAs detector, direct wavelength mapping in time is recorded, and the pressure induced FBG spectral shift is sampled at 50 MHz. Here, the sensing systems are used to monitor the spectral shifts of FBGs that are immersed into liquid water and shock compressed using explosives. In this configuration, the gratings survive to pressures approaching 50 kbar. We describe both approaches and present the measured spectral shifts from the shock experiments.

fiber Bragg grating sensors, shockwave diagnostics↗

Ejecta Particle-Size Measurements in Vacuum and Helium Gas using Ultraviolet In-Line Fraunhofer Holography

An ultraviolet (UV) in-line Fraunhofer holography diagnostic has been developed for making high-resolution spatial measurements of ejecta particles traveling at many mm/μsec. This report will discuss the development of the diagnostic, including the high-powered laser system and high-resolution optical relay system. In addition, we will also describe the system required to reconstruct the images from the hologram and the corresponding analysis of those images to extract particles. Finally, we will present results from six high-explosive (HE), shock-driven Sn-ejecta experiments. Particle-size distributions will be shown that cover most of the ejecta velocities for experiments conducted in a vacuum, and helium gas environments. In addition, a modification has been made to the laser system that produces two laser pulses separated by 6.8 ns. This double-pulsed capability allows a superposition of two holograms to be acquired at two different times, thus allowing ejecta velocities to be measured directly. Results from this double-pulsed experiment will be described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗