Engineering Papers⌕ Search

Engineering topics

Sternstein, S. S.

Publications and source records attributed to Sternstein, S. S..

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Microstructural non-uniformity as related to unidirectional compression performance

The compression performance of unidirectional composite laminates (UDCLs) is related not only to intrinsic or local strength, but also to a sample's ability to resist propagaton of initial damage. This paper introduces a simple shear lag model which is applied to a compression loaded UDCL with initial damage. Among the information obtained are axial overload and matrix layer shear strain factors in the neighborhood of the damage zone. These factors indicate that propagation may occur with relatively little initial damage and emphasize the need for a more complete understanding of compression behavior than currently exists.

Majors, Patrick S.↗
NASA NTRS1988

A micrographic study of bending failure in five thermoplastic-carbon fibre composite laminates

The local deformation and failure sequences of five thermoplastic matrix composites were microscopically observed while bending the samples in a small fixture attached to a microscope stage. The thermoplastics are polycarbonate, polysulfane, polyphenylsulfide, polyethersulfane, and polyetheretherketone. Comparison was made to an epoxy matrix composite, 5208/T-300. Laminates tested are (0/90) sub 2S, with outer ply fibers parallel to the beam axis. Four point bending was used at a typical span-to-thickness ratio of 39:1. It was found that all of the thermoplastic composites failed by abrupt longitudinal compression buckling of the outer ply. Very little precursory damage was observed. Micrographs reveal typical fiber kinking associated with longitudinal compression failure. Curved fracture surfaces on the fibers suggest they failed in bending rather than direct compression. Delamination was suppressed in the thermoplastic composites, and the delamination that did occur was found to be the result of compression buckling, rather than vice-versa. Microbuckling also caused other subsequent damage such as ply splitting, transverse ply shear failure, fiber tensile failure, and transverse ply cracking.

Yurgartis, S. W.↗
NASA NTRS1987

A micrographic study of bending failure in five thermoplastic/carbon fiber composite laminates

The local deformation and failure sequences of five thermoplastic matrix composites were microscopically observed while bending the samples in a small fixture attached to a microscope stage. The themoplastics are polycarbonate, polysulfone, polyphenylsulfide, polyethersulfone, and polyetheretherketone. Comparison was made to an epoxy matrix composite, 5208/T-300. Laminates tested are (0/90) sub 2S, with outer ply fibers parallel to the beam axis. Four point bending was used at a typical span-to-thickness ratio of 39:1. It was found that all of the thermoplastic composites failed by abrupt longitudinal compression buckling of the outer ply. Very little precursory damage was observed. Micrographs reveal typical fiber kinking associated with longitudinal compression failure. Curved fracture surfaces on the fibers suggest they failed in bending rather than direct compression. Delamination was suppressed in the thermoplastic composites, and the delamination that did occur was found to be the result of compression buckling, rather than visa-versa. Microbuckling also caused other subsequent damage such as ply splitting, transverse ply shear failure, fiber tensile failure, and transverse ply cracking.

Yurgartis, S. W.↗
NASA NTRS1984

Experimental and Theoretical Studies of Moisture and Temperature Effects on the Mechanical Properties of Graphite/Epoxy Laminates and Neat Resins

The properties of high performnce composites which are strongly dependent on the physical properties of the matrix resin were studied. Moisture adversely affect the properties of both neat epoxy resin and epoxy matrix composites. Inhomogeneous swelling as to the moisture degradation of mechanical properties, both in the neat resin and the composite. It is postulated that the postcuring process can change structure/moisture interactions and partially alleviate its adverse effects. The study is directed toward are understanding of the physical/mechanical/thermodynamic aspects of this problem.

Sternstein, S. S.↗
NASA NTRS1983

Dynamic-mechanical response of graphite/epoxy composite laminates and neat resin

Dynamic mechanical measurement results are presented for the case of carbon fiber-reinforced, epoxy matrix composite laminates subjected to loading perpendicular to the lamination plane, as well as for neat epoxy resin under the same conditions, where temperatures ranged between 20 and 200 C and deformation levels lie within the linear viscoelastic region. In-phase and out-of-phase stiffnesses are found to become superposed, forming master curves that cover a 12-decade frequency range. The application of a master curve scaling procedure shows that the in-phase stiffness has the same shape, and out-of-phase stiffness has the same dispersion, for all laminates irrespective of stacking sequence and are, in turn, nearly identical to those for the neat epoxy resin. An empirical function is found for the relaxation modulus which, when converted to a dynamic modulus, yields good overall agreement for both of the dynamic stiffness components as a function of frequency.

Yang, P.↗
NASA NTRS1983

Finite element analysis of moisture effects in graphite-epoxy composites

A numerical analysis procedure is developed for the micro-mechanical investigation of moisture effects on graphite-epoxy composites. The procedure employs a nonlinear constitutive relationship in a finite element formulation. A quasi-Newton method is used to solve the resulting nonlinear algebraic equations. The results presented indicate that the stresses at the graphite-epoxy interface have a strong dependence on moisture content, fiber spacing, and applied load.

Tobing, F. E. L.↗
NASA NTRS1983

Characterization of the matrix glass transition in carbon-epoxy laminates using the CSD test geometry

A new test geometry, referred to as centro-symmetric deformation (CSD), is proposed for characterizing the viscoelastic behavior of the matrix of carbon-epoxy laminates. The sample consists of a thin disk, typically 6-14 plies thick, having a nominal diameter of 30 mm. The disk is freely supported on a circular anvil; the load is applied to the center of the disk using an 8-mm-diameter ball bearing nosepiece. The CSD test geometry provides viscoelastic dispersion data which are independent of the angular orientation of the sample. The test geometry is sufficiently sensitive to matrix changes to allow its use for postcuring, humidity, crosslink density, and other matrix change studies. Test results are presented for a carbon-epoxy laminate.

Sternstein, S. S.↗
NASA NTRS1972

Biaxial stress relaxation in glassy polymers - Polymethylmethacrylate.

Biaxial stress relaxation studies were performed on glassy polymethylmethacrylate in combined torsion-tension strain fields using a specially designed apparatus with exceptionally high stiffness and low cross talk between the torsional and tensile load measuring transducers. It was found that at low strain levels uniaxial tension relaxation is slower than pure torsion relaxation; tensile-component relaxation rates are unaffected by the level of torsional strain; torsional-component relaxation rates decrease as tensile strain is increased; uniaxial tension relaxation rates approach the pure torsion rates at higher strains (about 2%). A phenomenological treatment is presented which shows that relaxation rates can be coupled to the strain fields in which they are observed and yet be consistent with the concepts of linear viscoelasticity and the Boltzmann superposition integral.

Sternstein, S. S.↗
NASA NTRS1964

Cellulose-fiber bonding

Hydrogen bond as predominant factor in inter- and intrafiber bonding in cellulose

HYDROGEN BOND↗