Engineering topics

Stepka, F. S.

Publications and source records attributed to Stepka, F. S..

At least 19 records

NASA NTRS1984

Review and status of heat-transfer technology for internal passages of air-cooled turbine blades

Selected literature on heat-transfer and pressure losses for airflow through passages for several cooling methods generally applicable to gas turbine blades is reviewed. Some useful correlating equations are highlighted. The status of turbine-blade internal air-cooling technology for both nonrotating and rotating blades is discussed and the areas where further research is needed are indicated. The cooling methods considered include convection cooling in passages, impingement cooling at the leading edge and at the midchord, and convection cooling in passages, augmented by pin fins and the use of roughened internal walls.

Yeh, F. C.↗

NASA NTRS1983

Comparison of predicted and experimental external heat transfer around a film cooled cylinder in crossflow

Calculations were made of the film cooling provided by rows of holes around the circumference of a cylinder in crossflow and the results were compared to experimental data. The calculations and experimental data were for conditions that simulate most of those that are typical of air cooled turbine vane leading edges. Injection was from a single and multiple rows of holes located at different angular locations from the stagnation line. The holes in the rows were angled normal to the flow direction and at a 25 degree angle to the cylinder wall. The calculations and experimental data were for several constant values of blowing ratios for all rows and for different blowing ratios for each row, representing a simulation of a common coolant plenum supply to multiple rows of holes. The calculations were made using a finite difference boundary layer code, STAN5. Contrary to initial expectations that injection would trip the boundary layer flow into the turbulent regime, the results indicated that the high free stream acceleration apparently kept the flow laminar for holes in the first 45 degrees past stagnation. The trend in Stanton number reduction due to coolant injection was predicted with generally good agreement at the lower blowing rates, but for multile rows of holes, agreement was poor beyond the first row.

Stepka, F. S.↗

NASA NTRS1982

Heater Composite Measures Heat Transfer

Composite consisting of commercially available elements has been developed to measure heat transfer. Composite provides a simple, convenient, low-cost device for use in heat-transfer work for rapid evaluation of thermal performance of both flat and simply curved objects. Device utilizes available off-the-shelf materials and provides a convenient method, with good resolution of local temperatures and heat transfer, with measurement accuracy at near-normal room conditions.

Hippensteele, S. A.↗

NASA NTRS1981

Thermal and flow analysis of a convection, air-cooled ceramic coated porous metal concept for turbine vanes

Analysis was made of the heat transfer and pressure drop through turbine vanes made of a sintered, porous metal coated with a thin layer of ceramic and convection cooled by spanwise flow of cooling air. The analysis was made to determine the feasibility of using this concept for cooling very small turbines, primarily for short duration applications such as in missile engines. The analysis was made for gas conditions of approximately 10 and 40 atm and 1644 K and with turbine vanes made of felt-type porous metals with relative densities from 0.2 and 0.6 and ceramic coating thicknesses of 0.076 to 0.254 mm.

Stepka, F. S.↗

NASA NTRS1981

Evaluation of a method for heat transfer measurements and thermal visualization using a composite of a heater element and liquid crystals

Commercially available elements of a composite consisting of a plastic sheet coated with liquid crystal, another sheet with a thin layer of a conducting material (gold or carbon), and copper bus bar strips were evaluated and found to provide a simple, convenient, accurate, and low-cost measuring device for use in heat transfer research. The particular feature of the composite is its ability to obtain local heat transfer coefficients and isotherm patterns that provide visual evaluation of the thermal performances of turbine blade cooling configurations. Examples of the use of the composite are presented.

Hippensteele, S. A.↗

NASA NTRS1981

Evaluation of a method for heat transfer measurements and thermal visualization using a composite of a heater element and liquid crystals

Hippensteele, S. A.↗

NASA NTRS1981

Thermal and flow analysis of a convection air-cooled ceramic coated porous metal concept for turbine vanes

The heat transfer and pressure drop through turbine vanes made of a sintered, porous metal coated with a thin layer of ceramic and convection cooled by spanwise flow of cooling air were analyzed. The analysis was made to determine the feasibility of using this concept for cooling very small turbines, primarily for short duration applications such as in missile engines. The analysis was made for gas conditions of approximately 10 and 40 atm and 1644 K and with turbine vanes made of felt type porous metals with relative densities from 0.2 to 0.6 and ceramic coating thicknesses of 0.076 to 0.254 mm.

Stepka, F. S.↗

NASA NTRS1980

Composite wall concept for high-temperature turbine shrouds - Heat transfer analysis

The variables affecting the design of a composite turbine shroud, consisting of a metal base, an interlayer of porous metal, and an outer layer of yttria-stabilized zirconia, are analyzed. Results show that significant reductions in the cooling-air to gas-flow ratio are indicated for the composite shrouds compared to an all-metal shroud that was only impingement air cooled. The good insulating properties of the ceramic reduced the temperatures of the porous metal and support wall significantly. For a given porous metal density and coolant- to gas-flow ratio, decreasing the thickness of the porous metal and increasing ceramic thickness resulted in lower support wall temperatures. To maintain given allowable inter-layer temperatures and coolantto gas-flow ratios, porous-metal density or thermal conductivity must increase as the ratio of the thickness of the ceramic-to-porous metal decreases. It is concluded that a 1.78 mm thickness of porous material with a density of 0.2 and a 1.78 mm thickness of ceramic appears to be a good composite wall configuration for the assumed conditions

Ludwig, L. P.↗

NASA NTRS1980

Uncertainties in predicting turbine blade metal temperatures

An analysis is presented of the effects of the hot-gas and coolant temperatures, the gas-to-blade and blade-to-coolant heat transfer coefficients, and the thermal conductances of a metal wall and a ceramic thermal-barrier coating on the prediction of local turbine-blade surface temperatures. The analysis was applied to the conditions of an advanced turbofan engine and a 1700 K, 40 atm turbine test rig, and to conditions that simulated the engine at 756 K and 15.6 atm. The results showed that with current information on boundary conditions, geometry, heat-transfer coefficients, and material thermal properties, the uncertainty in predicting and verifying local turbine-blade surface temperatures in an average engine is 98 kelvins or 7.6% of the reference metal absolute temperature for uncoated blades, and 62 kelvins or 5.7% for ceramic-thermal-barrier-coated blades.

Stepka, F. S.↗

NASA NTRS1980

Analysis of uncertainties in turbine metal temperature predictions

An analysis was conducted to examine the extent to which various factors influence the accuracy of analytically predicting turbine blade metal temperatures and to determine the uncertainties in these predictions for several accuracies of the influence factors. The advanced turbofan engine gas conditions of 1700 K and 40 atmospheres were considered along with those of a highly instrumented high temperature turbine test rig and a low temperature turbine rig that simulated the engine conditions. The analysis showed that the uncertainty in analytically predicting local blade temperature was as much as 98 K, or 7.6 percent of the metal absolute temperature, with current knowledge of the influence factors. The expected reductions in uncertainties in the influence factors with additional knowledge and tests should reduce the uncertainty in predicting blade metal temperature to 28 K, or 2.1 percent of the metal absolute temperature.

Stepka, F. S.↗

NASA NTRS1980

Composite wall concept for high temperature turbine shrouds: Heat transfer analysis

A heat transfer analysis was made of a composite wall shroud consisting of a ceramic thermal barrier layer bonded to a porous metal layer which, in turn, is bonded to a metal base. The porous metal layer serves to mitigate the strain differences between the ceramic and the metal base. Various combinations of ceramic and porous metal layer thicknesses and of porous metal densities and thermal conductivities were investigated to determine the layer thicknesses required to maintain a limiting temperature in the porous metal layer. Analysis showed that the composite wall offered significant air cooling flow reductions compared to an all impingement air cooled, all metal shroud.

Stepka, F. S.↗

NASA NTRS1979

Industry tests of NASA ceramic thermal barrier coating

Ceramic thermal barrier coating (TBC) system was tested by industrial and governmental organizations for a variety of aeronautical, marine, and ground-based gas turbine engine applications. This TBC is a two-layer system with a bond coating of nickel-chromium-aluminum-yttrium (Ni-16Cr-6Al-0.6Y, in wt. percent) and a ceramic coating of yttria-stabilized zirconia (ZrO2-12Y2O3, in wt. percent). Seven tests evaluated the system's thermal protection and durability. Five other tests determined thermal conductivity, vibratory fatigue characteristics, and corrosion resistance of the system. The information presented includes test results and photographs of the coated parts. Recommendations are made for improving the coating procedures.

Liebert, C. H.↗

NASA NTRS1979

Review and status of liquid-cooling technology for gas turbines

A review was conducted of liquid-cooled turbine technology. Selected liquid-cooled systems and methods are presented along with an assessment of the current technology status and requirements. A comprehensive bibliography is presented.

Vanfossen, G. J., Jr.↗

NASA NTRS1979

Turbomachinery technology

A technology assessment of turbomachinery is presented. The design of the fan, compressor, and turbine components for future advanced aircraft engines is discussed. Basic flow characteristics in compressors and turbines and the heat transfer phenomena in cooled turbines are also discussed.

Hauser, C. H.↗

NASA NTRS1978

NASA thermal barrier coatings - Summary and update

The work conducted at the NASA Lewis Research Center to evolve and evaluate a thermal-barrier coating system will be discussed. A durable, two-layer, plasma-sprayed coating consisting of a ceramic layer over a metallic layer was developed that has the potential of insulating hot engine parts and thereby reducing metal temperatures and coolant flow requirements and/or permitting use of less costly and complex cooling configurations and materials. The paper summarizes the results of analytical and experimental investigations of the coatings on flat metal specimens, turbine vanes and blades, and combustor liners. Discussed are results of investigations to determine coating adherence and durability, coating thermal, strength and fatigue properties, and chemical reactions of the coating with oxides and sulfates. Also presented are the effect of the coating on aerodynamic performance of a turbine vane, measured vane and combustor liner temperatures with and without the coating, and predicted turbine metal temperatures and coolant flow reductions potentially possible with the coating. Included also are summaries of some current research related to the coating and potential applications for the coating.

Stepka, F. S.↗

NASA NTRS1978

The NASA high pressure facility and turbine test rig

NASA Lewis Research Center is presently constructing a test facility for developing turbine-cooling and combustor technology for future-generation aircraft gas-turbine engines. Prototype engine hardware will be investigated in this facility at gas-stream conditions up to 2480 K average turbine inlet temperature and 4.14 million N/sq m turbine inlet pressure. The facility will have the unique features of fully automated control and data acquisition through the use of an integrated system of minicomputers and programmable controllers, which will result in more effective use of operating time and operators and will provide a built-in self-protection safety system. The facility, turbine rig, and turbine-cooling test program are described.

Stepka, F. S.↗

NASA NTRS1978

Liquid-cooling technology for gas turbines review and status

A review of research related to liquid cooling of gas turbines was conducted and an assessment of the state of the art was made. Various methods of liquid cooling turbines were reviewed. Examples and results with test and demonstrator turbines utilizing these methods along with the advantages and disadvantages of the various methods are discussed.

Vanfossen, G. J., Jr.↗

NASA NTRS1978

NASA thermal barrier coatings: Summary and update

A durable, two-layer, plasma-sprayed coating consisting of a ceramic layer over a metallic layer was developed that has the potential of insulating hot engine parts and thereby reducing metal temperatures and coolant flow requirements and/or permitting use of less costly and complex cooling configurations and materials. The results are summarized of analytical and experimental investigations of the coatings on flat metal specimens, turbine vanes and blades, and combustor liners. Discussed are results of investigations to determine coating adherence and durability, coating thermal, strength and fatigue properties, and chemical reactions of the coating with oxides and sulfates. Also presented are the effect of the coating on aerodynamic performance of a turbine vane, measured vane and combustor liner temperatures with and without the coating, and predicted turbine metal temperatures and coolant flow reductions potentially possible with the coating. Included also are summaries of some current research related to the coating and potential applications for the coating.

Stepka, F. S.↗