Realization of a Photoelectrochemical Cascade for the Generation of Methanol: A Liquid Solar Fuel
Not Available
3-terminal tandems↗
Engineering topics
Steiner, Myles A.
Publications and source records attributed to Steiner, Myles A..
Patterned dielectric back contact design for GaAs thermophotovoltaic devices
-Patterned-dielectric back contact structures in optoelectronic devices are designed to boost the reflectance of light from the device back surface while retaining a low-resistance pathway for electrical conductance. Their reduced light absorption at near- and sub-bandgap photon energies leads to improved luminescence in light-emitting diodes, greater photon recycling, voltage, and efficiency in photovoltaic cells, and greater recuperation of unabsorbed sub-bandgap light in thermophotovoltaic (TPV) systems. However, diffraction from the patterned features can deflect incident light in propagation directions that lead to light trapping and parasitic absorption in the cell. Here, in this article, we use rigorous coupled-wave analysis (RCWA) to study three-dimensional diffractive scattering of electromagnetic waves by periodic metal point-contact gratings on 1.42-eV GaAs TPV cells, to analyze their effect on unwanted sub-bandgap absorption in order to achieve higher TPV system efficiency. Solutions of Maxwell's equations calculated using RCWA are compared to measured sub-bandgap reflectance in experimental GaAs TPV devices with varying metal point-contact diameters and spacing. Modeling and experiments indicate decreased total reflectance due to these diffractive effects for a small point contact diameter of 1 μm, and this effect is much stronger at higher contact coverage fractions.
14 SOLAR ENERGY↗
Planarizing Spalled GaAs(100) Surfaces by MOVPE Growth
III-V photovoltaic devices have demonstrated exceptional performance across various applications, with controlled crystal fracturing, known as controlled spalling, emerging as a promising method to reduce costs by enabling substrate reuse. Spalling GaAs(100) substrates, a commonly used substrate in III-V photovoltaics, results in faceted ridges that must be planarized to grow high-quality photovoltaic devices. Here, in this study, we demonstrate that a GaAs(100) wafer offcut toward [$0\bar{11}$] and spalled toward [$011$] can be efficiently planarized by growing C:GaAs by metal-organic vapor phase epitaxy (MOVPE) on the surface, with up to 95% of the nominally deposited material used to fill the valleys between ridges. We find that reducing the offcut to 2° enhances the planarizing capability of C:GaAs. A surface morphology model indicates that the density of surface dangling bonds significantly influences the growth evolution of undoped GaAs surfaces. In contrast, the model suggests that the effectiveness of C:GaAs as a smoothing layer stems from modifying the atomic surface structure and, consequently, the associated sticking coefficients of the facets, which can alter the evolution of surface morphology. Our findings provide guidelines for the epitaxial planarization of semiconductor surfaces and improve the understanding of MOVPE growth on nonplanar surfaces.
14 SOLAR ENERGY↗
TiO 2 /TiN Interface Enables Integration of Ni 5 P 4 Electrocatalyst with a III–V Tandem Photoabsorber for Stable Unassisted Solar-Driven Water Splitting
H 2 production by direct photoelectrochemical (PEC) water splitting has remained unachievable commercially, mainly due to rapid failure at the interface between the photoabsorber(s) and catalyst(s). PEC devices made from multijunction III-V semiconductors with platinum group metal (PGM) catalysts have yielded impressive initial solar-to-H 2 (STH) efficiency >19%, which rapidly corrodes in aqueous electrolytes. Here, TiO 2 /TiN layers were fused to create a bifunctional interface between a GaInP 2 /GaAs III-V tandem photoabsorber and a polycrystalline Ni 5 P 4 HER catalyst. Here, the TiO 2 serves as a conducting corrosion barrier, while a thin layer of much denser TiN (1 nm) blocks interlayer diffusion during fabrication. This strategy allows the elevated temperatures needed to crystallize the Ni 5 P 4 nanoparticles and fuse to the TiO 2 /TiN junction to achieve minimal optical loss without damaging the sensitive photoasbsorber. The resulting photocathode exhibits an initial STH efficiency of 11.4%-13.2% in sodium phosphate electrolyte at neutral pH 7. It operated continuously for over 200 h without failure above 10% STH efficiency, exceeding all previous benchmarks. The earth-abundant Ni 5 P 4 catalyst replaces costly PGM catalysts at comparable HER activity in neutral, acidic, or basic pH electrolytes.
08 HYDROGEN↗
Sub‐0.6 eV Inverted Metamorphic GaInAs Cells Grown on Inp and GaAs Substrates for Thermophotovoltaics and Laser Power Conversion
Abstract Inverted metamorphic Ga 0.3 In 0.7 As photovoltaic converters with sub‐0.60 eV bandgaps grown on InP and GaAs are presented. Threading dislocation densities are 1.3 ± 0.6 × 10 6 and 8.9 ± 1.7 × 10 6 cm −2 on InP and GaAs, respectively. The devices generate open‐circuit voltages of 0.386 and 0.383 V, respectively, under irradiance producing a short‐circuit current density of ≈10 A cm −2 , yielding bandgap‐voltage offsets of 0.20 and 0.21 V. Power and broadband reflectance measurements are used to estimate thermophotovoltaic (TPV) efficiency. The InP‐based cell is estimated to yield 1.09 W cm −2 at 1100 °C versus 0.92 W cm −2 for the GaAs‐based cell, with efficiencies of 16.8 versus 9.2%. The efficiencies of both devices are limited by sub‐bandgap absorption, with power weighted sub‐bandgap reflectances of 81% and 58%, respectively, the majority of which is assumed to occur in the graded buffers. The 1100 °C TPV efficiencies are estimated to increase to 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application to laser power conversion in the 2.0–2.3 µm atmospheric window. Peak laser power converter efficiencies of 36.8% and 32.5% are estimated under 2.0 µm irradiances of 1.86 and 2.81 W cm −2 , respectively.
14 SOLAR ENERGY↗
Doped GaInAs/GaP Quantum Well Superlattice Solar Cells With 27.5% Efficiency
Quantum wells can extend the absorption range of a solar cell and are typically placed in the intrinsic region of the device to enable efficient carrier collection via drift. Thick intrinsic regions are needed for significant absorption in the low bandgap quantum wells, resulting in a large depletion region recombination and ultimately a solar cell with a low fill factor (FF). However, in quantum well superlattice solar cells where tunneling plays a dominant role in carrier transport, collection by carrier diffusion may be possible, relieving the requirement for quantum wells to be placed in the intrinsic region. Here, we investigate doping in stress-balanced quantum well superlattice solar cells using thin 2 nm GaP barriers. Doping reduces J02 depletion region recombination and improves the solar cell FF up to 86.7%, but very high doping eventually reduces the carrier collection, leading to a tradeoff in efficiency. Finally, we show that the barrier thickness also plays an important role in carrier collection, and we demonstrate high efficiency 27.5% single-junction devices with a doped superlattice.
13 HYDRO ENERGY↗
Operando Temperature Measurements of Photovoltaic Laser Power Converter Devices Under Continuous High-Intensity Illumination
Photovoltaic devices that operate under extremely high irradiances, such as laser power converters (LPCs), may also operate at elevated temperatures, even under active cooling, as the result of large temperature gradients. We demonstrate the operation of GaAs LPC devices under orders of magnitude of irradiances up to 150 W/cm 2 in a monochromatic laser simulator with an active cooling stage. The steady-state open-circuit voltage (V OC ) as a function of irradiance is known to droop at high irradiance as the result of junction heating, but the junction temperature can be difficult to measure by conventional methods. Fast, transient V OC measurements under these extreme operating conditions are used here to determine the junction temperature. Empirical V OC temperature coefficients of the devices at each irradiance of interest are determined and used as an integral part of this technique. We show that the thermal design of different LPC devices strongly affects the operating temperature of the junctions. Knowledge of the operating temperature can be a strong tool for understanding the nature of loss mechanisms and improving the design for the operation of photovoltaic LPCs at high irradiances. Furthermore, this technique can be used for laboratory devices during initial design as well as to characterize mass-produced and packaged devices for quality control.
14 SOLAR ENERGY↗
Modeling and design of III-V heterojunction solar cells for enhanced performance
Heterojunctions can increase the efficiency of solar cell devices relative to homojunctions, but there is a large parameter space with significant tradeoffs that must be considered. Here, we present an experimental and computational study of III-V heterojunction solar cells and show how the emitter doping, emitter band gap, and heteroband offsets impact device efficiency. Efficiency is maximized by pushing the junction depletion region into the wider band gap material while minimizing the effects of heteroband offsets through optimized choice of emitter band gap, emitter electron affinity, and/or emitter doping density. We use these results to guide optimization of devices grown by halide vapor phase epitaxy, achieving 27% efficiency in a GaAs/GaInPAs heterojunction device. We also show that heterojunctions yield proportionally larger efficiency improvements in lower-quality materials. Although the modeling was developed and validated using III-V materials, the results are theoretically applicable to materials systems outside III-Vs.
14 SOLAR ENERGY↗
GaAs solar cells grown on acoustically spalled GaAs substrates with 27% efficiency
Acoustic spalling presents a potentially low-cost reuse pathway for III–V epitaxial growth substrates via exfoliation of device layers with recovery and reuse of the substrate. However, surface features formed during spalling can reduce the performance of subsequently grown devices. Here, we develop an understanding of how the surface morphology of acoustically spalled substrates affects GaAs solar cell performance and develop strategies to mitigate these impacts. We demonstrate that minor planarization of the surface by wet chemical etching and/or epitaxial growth, or the redesign of the device structure to thicken critical layers, prevents performance degradation. Using these strategies, we demonstrate a 0.25 cm 2 single-junction GaAs device with 26.9% ± 0.2% photovoltaic conversion efficiency under the AM1.5G spectrum grown on an acoustically spalled substrate. These results enable the growth of high-performance III–V devices on non-traditional substrates with the potential for significantly reduced device costs.
14 SOLAR ENERGY↗
Pulsed laser ejection of single-crystalline III-V solar cells from GaAs substrates
The best III-V solar cells start out as single-crystalline multilayers on GaAs substrates. Separating these multilayers from their growth substrate enables higher performance and wafer reuse, which are both critical for terrestrial III-V solar cell viability. Here, we remove rigidly bonded, 16 mm 2 x 3.5μm thick devices from a GaAs substrate using an unfocused Nd:YAG laser pulse. The pulse is absorbed by a low-bandgap, lattice-matched layer below the device, driving an ablation event that ejected the crystalline multilayer from the substrate. Minutes of selective wet-chemical etching and device finishing yield a 0.1 cm 2 device with a 17.4% power conversion efficiency and open-circuit voltage of 1.07 V, using AM1.5 direct with no anti-reflection coating. We show that the performance is comparable to similar cells produced via conventional processes. We discuss unique process characteristics, such as the potential to separate wafer-sized solar cells per laser pulse.
14 SOLAR ENERGY↗
A framework for understanding efficient diurnal CO 2 reduction using Si and GaAs photocathodes
Integrated solar fuels and photoelectrochemical (PEC) CO 2 reduction (CO 2 R) are promising pathways toward producing value-added chemicals from CO 2 . However, improvements are needed in activity and selectivity as well as in fundamental understanding of device behavior to engender wide deployment. Here, we report two single-junction, integrated photocathodes for PEC CO 2 R based on TOPCon Si and GaAs substrates, which achieve -10 mA cm -2 at -0.33 V vs. RHE with 41% selectivity to C 2+ products and at -0.03 V vs. RHE with 27% selectivity to C 2+ products, respectively. We investigated the viability of a light-mediated strategy to direct selectivity in buried-junction PEC devices and confirmed that these devices could be optimized independently and described by the physics-based models of the individual components. Finally, we designed a framework to assess operational modes for PEC CO 2 R devices and demonstrated this framework under continuous galvanostatic control and variable illumination conditions.
14 SOLAR ENERGY↗
Analysis of Crystalline Defects Caused by Growth on Partially Planarized Spalled (100) GaAs Substrates
We analyze the effect of growth on non-(100) surfaces resulting from incomplete planarization of spalled GaAs wafers on the defect structure of GaAs solar cell layers grown by hydride vapor phase epitaxy (HVPE). Controlled spalling of (100)-oriented GaAs has the potential to reduce substrate costs for III-V epitaxy; however, it creates regularly faceted surfaces that may complicate the growth of high-quality III-V optoelectronic devices. We leverage the anisotropic growth rate of HVPE to planarize these faceted GaAs substrates, reducing the surface roughness and degree of faceting. We observe degraded solar cell performance and material quality in sample areas where facets are not completely removed. We used dark lock-in thermography and photoluminescence to identify recombination in areas that were not fully planarized. We used cathodoluminescence to identify the presence of extended defects in these regions, which are correlated with bandgap fluctuations in the material. We hypothesize that these defects were created by strain from compositional fluctuations in ternary alloys grown on the faceted surfaces. This work elucidates the potential issues of solar cells grown on faceted surfaces and builds understanding toward realizing high performance III-V photovoltaics with the cost-reduction potential of controlled spalling.
14 SOLAR ENERGY↗
III-V PV Cell Core Capability (Final Technical Report)
This Core project developed III-V photovoltaics for terrestrial applications, focusing on high efficiency architectures and on cost-reduction. III-V cells have demonstrated the highest efficiencies of any photovoltaic materials system, reaching over 30% for two- junction tandems and over 47% for more complex concentrator cells. III-Vs have other characteristics that make them attractive to a range of terrestrial and near-terrestrial energy applications, such as being direct absorbers, lightweight and potentially flexible, having good thermal coefficient, good radiation hardness, and being very stable and durable. Cost is a key challenge with III-Vs, however, because of the high cost of epitaxy and processing.
14 SOLAR ENERGY↗
Optically thick GaInAs/GaAsP strain-balanced quantum-well tandem solar cells with 29.2% efficiency under the AM0 space spectrum
GaAs is often used as a multijunction subcell due to its high material quality on GaAs substrates, despite having a non-optimal bandgap. The bandgap can be beneficially reduced using many layers of thin, strain-balanced GaInAs in a superlattice or quantum well device, but achieving excellent carrier collection without increased recombination has proven challenging. Here, we develop and demonstrate high performance, optically thick GaInAs/GaAsP strain-balanced solar cells. Excellent material quality is achieved in thick superlattices by using growth conditions that limit progressive thickness and composition fluctuations. Bandgap-voltage offsets as low as 0.31V are shown in superlattice cells using thin, highly strained GaP barriers. Optically thick superlattice cells with over 2500 nm of total GaInAs in the depletion region are developed, enabling 3.8 mA/cm 2 of extra photocurrent beyond the GaAs band edge under the AM0 space spectrum. Optimized superlattice solar cells are incorporated into two-junction devices that achieve 29.2% efficiency under the AM0 space spectrum due to their improved bandgap combination and high subcell voltages.
14 SOLAR ENERGY↗
Fabrication methods for high reflectance dielectric-metal point contact rear mirror for optoelectronic devices
The patterned dielectric back contact (PDBC) structure can be used to form a point-contact architecture that features a dielectric spacer with spatially distributed, reduced-area metal point contacts between the semiconductor back not recognized contact layer and the metal back contact. In this structure, the dielectric-metal region provides higher reflectance and is electrically insulating. Reduced-area metal point contacts provide electrical conduction for the back contact but typically have lower reflectance. The fabrication methods discussed in this article were developed for thermophotovoltaic cells, but they apply to any III-V optoelectronic device requiring the use of a conductive and highly reflective back contact. Patterned dielectric back contacts may be used for enhanced sub-bandgap reflectance, for enhanced photon recycling near the bandgap energy, or both depending on the optoelectronic application. The following fabrication methods are discussed in the article: PDBC fabrication procedures for spin-on dielectrics and commonly evaporated dielectrics to form the spacer layer; methods to selectively etch a parasitically absorbing back contact layer using metal point contacts as an etch mask; methods incorporating a dielectric etch through different process techniques such as reactive ion and wet etching.
14 SOLAR ENERGY↗
Efficient and scalable GaInAs thermophotovoltaic devices
We report thermophotovoltaics are promising solid-state energy converters for a variety of applications such as grid-scale energy storage, concentrating solar-thermal power, and waste-heat recovery. Here, we report the design, fabrication, and testing of large area (0.8 cm 2 ), scalable, single-junction 0.75-eV GaInAs thermophotovoltaic devices reaching an efficiency of 38.8% +/- 2.0% and an electrical power density of 3.78 W/cm 2 at an emitter temperature of 1,850 °C. Reaching such a high emitter temperature and power density without sacrificing efficiency is a direct result of combining good spectral management with an optimized cell architecture, excellent material quality, and low series resistance. Importantly, fabrication of 12 high-performing devices on a 2-in wafer is shown to be repeatable, and the cell design can be readily transferred to commercial epitaxy on even larger wafers. Further improvements in efficiency can be obtained by using a multijunction architecture, illustrated by early results for a two-junction 0.84-eV GaInPAs/0.75-eV GaInAs device.
14 SOLAR ENERGY↗