Engineering topics

Stanton, P. H.

Publications and source records attributed to Stanton, P. H..

14 records

NASA NTRS1996

A prototype Ka-/Ka-band dichroic plate with stepped rectangular apertures

A prototype five-layer Ka-/Ka-band dichroic plate was fabricated and measured. This dichroic plate was designed to pass Ka-band uplink (34.2-34.7 GHz) and to reflect Ka-band downlink (31.8-32.3 GHz) for dual-frequency operation in the Deep Space Network to support the future Cassini mission. The theoretical calculation and the experimental measurement of the reflected resonant frequencies were within 0.24 percent for circular polarization. The computer program, which was used to design the dichroic plate with stepped apertures, was then verified.

Chen, J. C.↗

NASA NTRS1996

A Prototype Ka-/Ka-Band Dichroic Plate With Stepped Rectangular Apertures

Chen, J. C.↗

NASA NTRS1993

Performance of the X-/Ka/KABLE-band dichroic plate in the DSS-13 beam waveguide antenna

The first Ka-band downlink demonstration was recently carried out by the Ka-Band Link Experiment (KABLE) in association with the Mars Observer spacecraft. In order to support the mission, a dichroic plate was required in the DSS-13 beam waveguide antenna to allow simultaneous X- and Ka-band operation. An X-/ Ka-/ KABLE-band dichroic plate was designed to transmit Ka-band downlink (31.8-32.3 GHz), Ka-band uplink (34.2-34.7 GHz), and KABLE (33.6-33.8 GHz) frequencies, while reflecting X-band (8.4-8.5 GHz). A computer program was developed for the analysis of a dichroic plate with rectangular apertures by using the mode-matching method. The plate was then fabricated and tested. The reflection, group delay, and noise temperature in the antenna system due to the dichroic plate were measured. The experimental results show good agreement with theoretical prediction.

Chen, J. C.↗

NASA NTRS1993

HRMS sky survey wideband feed system design for DSS 24 beam waveguide antenna

The High-Resolution Microwave Survey (HRMS) Sky Survey project will be implemented on the DSS 24 beam waveguide (BWG) antenna over the frequency range of 2.86 to 10 GHz. Two wideband, ring-loaded, corrugated feed horns were designed to cover this range. The horns match the frequency-dependent gain requirements for the DSS 24 BWG system. The performance of the feed horns and the calculated system performance of DSS 24 are presented.

Stanton, P. H.↗

NASA NTRS1993

Experimental and modal verification of an integral equation solution for a thin-walled dichroic plate with cross-shaped holes

In order to add the capability of an X-band uplink onto the 70-m antenna, a new dichroic plate is needed to replace the Pyle-guide-shaped dichroic plate currently in use. The replacement dichroic plate must exhibit an additional passband at the new uplink frequency of 7.165 GHz, while still maintaining a passband at the existing downlink frequency of 8.425 GHz. Because of the wide frequency separation of these two passbands, conventional methods of designing air-filled dichroic plates exhibit grating lobe problems. A new method of solving this problem by using a dichroic plate with cross-shaped holes is presented and verified experimentally. Two checks of the integral equation solution are described. One is the comparison to a modal analysis for the limiting cross shape of a square hole. As a final check, a prototype dichroic plate with cross-shaped holes was built and measured.

Epp, L. W.↗

NASA NTRS1992

SETI low-frequency feed design study for DSS 24

The Search for Extraterrestrial Intelligence Sky Survey project requires operation from 1 to 10 GHz on the beam waveguide (BWG) antenna DSS 24. The BWG reflectors are undersized in the 1- to 3.02-GHz range, resulting in poor performance. Horn designs and a method for implementing 1- to 3.02-GHz operation on DSS 24 are presented. A combination of a horn and a shaped feed reflector placed above the main reflector is suggested. The horn and feed reflector could be hidden in the RF shadow of the subreflector and struts. Results from computer analysis of this design indicate that adequate performance could be achieved.

Stanton, P. H.↗

NASA NTRS1991

The L-/C-band feed design for the DSS 14 70-meter antenna (Phobos mission)

A dual-frequency (1.668 and 5.01 GHz) feed was designed for the Deep Space Station (DSS) 14 70-m antenna to support the Soviet Phobos Mission. This antenna system was capable of supporting telemetry, two-way Doppler, and very long baseline interferometry (VLBI). VLBI and two-way Doppler information on the Phobos spacecraft was acquired with this antenna in 1989.

Stanton, P. H.↗

NASA NTRS1987

X-band phase calibration generator coupler

A new type of phase calibration generator (PCG) coupler was developed for the Deep Space Network (DSN) X-band antennas that can be located directly behind the feedhorn. The advantage of this is that the calibration includes more of the system. The disadvantage is that the overmoded waveguide at this location must be coupled in a mode-selective manner. Low-power and high-power PCG couplers have been successfully produced, and the RF test results from a PCG coupler are given.

Stanton, P. H.↗

NASA NTRS1987

Harmonic measurements of the Galileo spacecraft X-band transmitter system

Harmonics of X-band (8.4 GHz) spacecraft transmitter systems can be used to measure the performance characteristics of higher frequency deep space communication links. The Galileo X-band transmitter system was measured at the second, third, and fourth harmonics (16.8, 25.2, and 33.6 GHz, respectively). The effective isotropic radiated power was determined to be approximately 52 dBm at 16.8 GHz, 47 dBm at 25.2 GHz, and 25 dBm at 33.6 GHz. These values can be useful, depending upon the sensitivity of the Earth-based receiving system and the distance of the spacecraft from Earth.

Stanton, P. H.↗

NASA NTRS1985

Circularly-Polarized Microstrip Antenna

Microstrip construction compact for mobile applications. Circularly polarized microstrip antenna made of concentric cylindrical layers of conductive and dielectric materials. Coaxial cable feedlines connected to horizontal and vertical subelements from inside. Vertical subelement acts as ground for horizontal subelement.

Stanton, P. H.↗

NASA NTRS1979

Improved isolation in double-balanced mixers

Bypass circuit eliminates unwanted leakage in output RF signal. Correction circuit was developed for phase-shift-keyed transmitters. Principle can be adapted to correct leakage in other types of RF circuitry as well.

Stanton, P. H.↗

NASA NTRS1978

A bandwidth compressive modulation system using multi-amplitude minimum shift keying /MAMSK/

A bandwidth compressive modem making use of multi-amplitude minimum shift keying (MAMSK) has been designed and implemented in a laboratory environment at microwave frequencies. This system achieves a substantial bandwidth reduction over binary PSK and operates within 0.5 dB of theoretical performance. A number of easily implemented microwave transmitters have been designed to generate the required set of 16 signals. The receiver has been designed to work at 1 Mbit/s and contains the necessary phase tracking, AGC, and symbol synchronization loops as well as a lock detector, SNR estimator and provisions for differential decoding. This paper describes this entire system and presents the experimental results.

Weber, W. J., III↗

NASA NTRS1976

The effects of an ion-thruster exhaust plume on S-band carrier transmission

The study reported here was undertaken (1) to develop models of the effects of an ion-thruster exhaust plume on S-band signals, and (2) to measure the effects. The results show that an S-band signal passing through an ion-thruster plume is reduced in amplitude and advanced in phase. The mathematical models gave reasonable estimates of the average signal attenuation and phase shift. Negligible fluctuations in the signal amplitude and phase were measured during steady-state thruster operation. However, large jumps in phase occurred when changes were made in the thruster operating state. This study confirms that the thruster plume can have a significant effect on S-band communication link performance; hence the plume effects must be considered in S-band link calculations when electric thrusters are used for spacecraft propulsion.

Ackerknecht, W. E.↗

NASA NTRS1976

The effects of an ion-thruster exhaust plume on S-band carrier transmission

The magnitude of the effects of an ion thruster plume on S-band signals is measured. Modeling techniques are developed to predict the effects. Results show that the RF signal transmitted through an ion thruster plume is reduced in amplitude and shifted in phase. An increase in noise is also experienced.

Ackerknecht, W. E., III↗