Engineering Papers⌕ Search

Engineering topics

Stan, Mark A.

Publications and source records attributed to Stan, Mark A..

5 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

High-Efficiency Multi-Junction Space Solar Development Utilizing Lattice Grading

Progress towards achieving a high one-sun air mass 0 (AM0) efficiency in a monolithic dual junction solar cell comprised of a 1.62 eV InGaP top cell and a 1.1 eV InGaAs bottom cell grown on buffered GaAs is reported. The performance of stand-alone 1.62 eV InGaP and 1.1 eV InGaAs cells is compared to that of the dual junction cell. Projected AM0 efficiencies of 15.7% and 16.5% are expected for the 1.62 eV InGaP and 1.1 eV InGaAs cells grown on buffered GaAs. The dual junction cell has a projected one-sun AM0 conversion efficiency of 17%. The projected efficiencies are based upon the application of an optimized anti-reflective coating (ARC) to the as-grown cells. Quantum efficiency (QE) data obtained from the dual junction cell indicate that is is bottom cell current limited with the top cell generating 50% more current than the bottom cell. A comparison of the QE data for the stand-alone 1.1 eV InGaAs cell to that of the 1.1 eV InGaAs bottom cell in the tandem configuration indicates a degradation of the bottom cell conversion efficiency in the tandem configuration. The origin of this performance degradation is at present unknown. If the present limitation can be overcome, then a one-sun AM0 efficiency of 26% is achievable with the 1.62 eV/1.1 eV dual junction cell grown lattice-mismatched to GaAs.

Stan, Mark A.↗
NASA NTRS1998

Spray Chemical Vapor Deposition of CulnS2 Thin Films for Application in Solar Cell Devices

Chalcopyrite CuInS2 is a direct band gap semiconductor (1.5 eV) that has potential applications in photovoltaic thin film and photoelectrochemical devices. We have successfully employed spray chemical vapor deposition using the previously known, single-source, metalorganic precursor, (Ph3P)2CuIn(SEt)4, to deposit CuInS2 thin films. Stoichiometric, polycrystalline films were deposited onto fused silica over a range of temperatures (300-400 C). Morphology was observed to vary with temperature: spheroidal features were obtained at lower temperatures and angular features at 400 C. At even higher temperatures (500 C), a Cu-deficient phase, CuIn5S8, was obtained as a single phase. The CuInS2 films were determined to have a direct band gap of ca. 1.4 eV.

Hollingsworth, Jennifer A.↗
NASA NTRS1992

Conductor-backed coplanar waveguide resonators of YBa2Cu3O(7-delta) on LaAlO3

Conductor-backed coplanar waveguide (CBCPW) resonators operating at 10.8 GHz have been fabricated from laser ablated and off-axis magnetron sputtered YBa2Cu3O(7-delta) (YBCO) high-temperature superconducting (HTS) thin films on LaAlO3. These resonators were tested in the temperature range from 14 to 92 K. The unloaded quality factor at 77 K of the HTS CBCPW resonators was 3 to 4 times that of a similar gold resonator. To the authors' knowledge, these results represent the first reported measurements of HTS-based CBCPW resonators.

Miranda, Felix A.↗
NASA NTRS1991

Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

ErBa2Cu3O(7-x) films have been produced by simultaneous deposition of Er, Ba, and Cu from three ionized cluster beam (ICB) sources at acceleration voltages of 0.3 to 0.5 kV. Combining ozone oxidation with ICB deposition at 650 C eliminated any need of post annealing processing. The substrates were rotated at 10 rotations per minute during the deposition which took place at a rate of about 3 to 4 nm. Films with areas up to 70 mm in diameter have been made by ICB deposition. These films, 100 nm thick, were deposited on SrTiO3 (100) substrates at 650 C in a mixture of six percent O3 in O2 at a total pressure of 4 x 10(exp -4) Torr. They had T(sub c) ranging from 84.3 K to 86.8 K over a 70 mm diameter and J(sub c) above 10(exp 6) A/sq cm at 77 K. X ray diffraction measurements of the three samples showed preferential c-axis orientation normal to the substrate surface. Scanning electron micrographs (SEM) of the three samples also show some texture dependence on sample position. For the three samples, there is a correlation between SEM texture, full width at half-maximum of rocking curves and J(sub c) versus temperature curves.

Levenson, L. L.↗