Engineering topics

Srinivasan, S.

Publications and source records attributed to Srinivasan, S..

At least 19 records

NASA NTRS1992

Capacity retention in hydrogen storage alloys

Results of our examination of the properties of several candidate materials for hydrogen storage electrodes and their relation to the decrease in H-storage capacity upon open-circuit storage over time are reported. In some of the alloy samples examined to date, only about 10 percent of the hydrogen capacity was lost upon storage for 20 days, while in others, this number was as high as 30 percent for the same period of time. This loss in capacity is attributed to two separate mechanisms: (1) hydrogen desorbed from the electrode due to pressure differences between the cell and the electrode sample; and (2) chemical and/or electrochemical degradation of the alloy electrode upon exposure to the cell environment. The former process is a direct consequence of the equilibrium dissociation pressure of the hydride alloy phase and the partial pressure of hydrogen in the hydride phase in equilibrium with that in the electrolyte environment, while the latter is related to the stability of the alloy phase in the cell environment. Comparison of the equilibrium gas-phase dissociation pressures of these alloys indicate that reversible loss of hydrogen capacity is higher in alloys with P(eqm) greater than 1 atm than in those with P(eqm) less than 1 atm.

Anani, A.↗

NASA NTRS1991

Navier-Stokes calculations of transonic flows past cavities

Presented in this paper is a computational investigation of subsonic and transonic flows past three-dimensional deep and transitional cavities. Simulations of these self-induced oscillatory flows have been generated through time-accurate solutions of the Reynolds averaged, full Navier-Stokes equations, using the explicit MacCormack scheme. The Reynolds stresses have been included through the Baldwin-Lomax algebraic turbulence model with certain modifications. The computational results include instantaneous and time averaged flow properties. The results of an experimental investigation have been used not only to validate the time-averaged results, but also to investigate the effects of varying the Mach number and the incoming boundary-layer thickness. Time series analyses have been performed for the instantaneous pressure values on the cavity floor and compared with the results obtained by a predictive formula. While most of the comparisons have been favorable, some discrepancies have been observed, particularly on the rear face. The present results help understanding the three-dimensional and unsteady features of the separations, vortices, the shear layer, as well as some of the aeroacoustic phenomena of compressible cavity flows.

Baysal, O.↗

NASA NTRS1990

A numerical parametric study of a scramjet inlet in a Mach 6 arc heated test facility

A numerical study of the NASA Langley Arc Heated Scramjet Test Facility (AHSTF) is reported. The facility test flow through the Mach 6 quasi-two-dimensional nozzle was computed, and the flow through the Langley parametric inlet was calculated using different regions of the computed facility nozzle exit flow as inflow, exploring in more detail the effect of boundary layer ingestion on inlet performance. The potential advantage of using a quasi-two-dimensional nozzle in the Langley AHSTF versus the square cross-sectioned nozzle currently used for Scramujet engine tests is explored in terms of resulting inlet performance.

Sekar, B.↗

NASA NTRS1990

Novel approaches for fabrication of thin film layers for solid oxide electrolyte fuel cells

The main objectives of the SOFC (solid oxide fuel cell) project are to (1) identify viable and cost-effective techniques to prepare cell components for stable MSOFCs (monolithic SOFCs); (2) fabricate half and single cells; and (3) evaluate their performances. The approach used to fabricate stable MSOFCs is as follows: (1) the electrolyte layer is prepared in the form of a honeycomb structure by alloy oxidation and other cell components are deposited on it; (2) the electrolyte and anode layers are deposited on the cathode layer, which has a porous, honeycomb structure; and (3) the electrolyte and cathode layers are deposited on the anode layer. The current status of the project is reported.

Murugesamoorthi, K. A.↗

NASA NTRS1988

A flexible search strategy for production systems

Most problems considered to be solvable by expert systems have very large search space. It is imperative to use efficient search strategy in expert system tools. Thus, OPS5 uses a kind of hill climbing which is very efficient. However, hill climbing is inadequate for many problems because it is one of the least dependable search strategies. In order to make the search efficient and adequate one can: (1) adopt best-first search instead of hill climbing, or (2) modify hill climbing with intelligent backtracking. The second alternative is adopted. It is implemented in a production system called PRO2 embedded in C running on UNIX. It is called hill tracking. It is a general purpose tool for developing expert systems. This is a rule based production system with an effective, intelligent and flexible backtracking control mechanism, which makes the system more dependable. The advantages and disadvantages of PRO2 are discussed.

Dey, Pradip↗

NASA NTRS1988

Unsteady viscous calculations of supersonic flows past deep and shallow three-dimensional cavities

Computational simulations were performed for supersonic, turbulent flows over deep and shallow three-dimensional cavities. The width and the depth of these cavities were fixed at 2.5 in. and 0.5 in., respectively. Length-to-depth ratio of the deep cavity was 6 and that of the shallow cavity was 16. Freestream values of Mach number and Reynolds number were 1.50 and 2.0 x 10 to the 6th/ft., respectively, at a total temperature of 585 R. The thickness of the turbulent boundary layer at the front lip of the cavity was 0.2 in. Simulations of these oscillatory flows were generated through time-accurate solutions of Reynolds-averaged full Navier-Stokes equations using the explicit MacCormack scheme. The solutions are validated through comparisons with experimental data. The features of open and closed cavity flows and effects of the third dimension are illustrated through computational graphics.

Baysal, O.↗

NASA NTRS1988

Navier-Stokes calculations of transonic flows past open and transitional cavities

Computational simulations of deep and transitional cavities at transonic regimes were performed. The three-dimensional unsteady separation on the cavity floor was analyzed, and computational flow visualization inside the cavity was done. A parametric study was performed to investigate the effects of varying Mach number and the ratio delta/D, where delta is the instantaneous boundary layer thickness at the upstream lip and D is the depth. Both time-averaged and instantaneous solutions were obtained. Comparison of the solutions with experimental data were generally favorable; some discrepancies are explained.

Srinivasan, S.↗

NASA NTRS1987

Simplified curve fits for the transport properties of equilibrium air

New, improved curve fits for the transport properties of equilibruim air have been developed. The curve fits are for viscosity and Prandtl number as functions of temperature and density, and viscosity and thermal conductivity as functions of internal energy and density. The curve fits were constructed using grabau-type transition functions to model the tranport properties of Peng and Pindroh. The resulting curve fits are sufficiently accurate and self-contained so that they can be readily incorporated into new or existing computational fluid dynamics codes. The range of validity of the new curve fits are temperatures up to 15,000 K densities from 10 to the -5 to 10 amagats (rho/rho sub o).

Srinivasan, S.↗

NASA NTRS1987

Simplified curve fits for the thermodynamic properties of equilibrium air

New, improved curve fits for the thermodynamic properties of equilibrium air have been developed. The curve fits are for pressure, speed of sound, temperature, entropy, enthalpy, density, and internal energy. These curve fits can be readily incorporated into new or existing computational fluid dynamics codes if real gas effects are desired. The curve fits are constructed from Grabau-type transition functions to model the thermodynamic surfaces in a piecewise manner. The accuracies and continuity of these curve fits are substantially improved over those of previous curve fits. These improvements are due to the incorporation of a small number of additional terms in the approximating polynomials and careful choices of the transition functions. The ranges of validity of the new curve fits are temperatures up to 25 000 K and densities from 10 to the -7 to 10 to the 3d power amagats.

Srinivasan, S.↗

NASA NTRS1987

Structural elements and organization of the ancestral translational machinery

The molecular mechanisms of the primitive translational apparatus are discussed in the framework of present-day protein biosynthesis. The structural necessities of an early adaptor and the multipoint recognition properties of such an adaptor are investigated on the basis of structure/function relationships found in a contemporary system and a molecular model of the contemporary transpeptidation complex. A model of the tRNA(Tyr)-tyrosyl tRNA synthetase complex including the positioning of the disordered region is proposed; the model is used to illustrate the required recognition properties of the ancestor aminoacyl synthetase.

Rein, R.↗

NASA NTRS1987

Calculation of wall and free turbulent-shear flows at supersonic speeds

Supersonic turbulent flows are simulated numerically by solving the Reynolds-averaged full Navier-Stokes equations by an implicit finite-volume method. This flux-vector-split upwind scheme uses approximate factorization followed by line-Gauss-Seidel relaxations. The effects of turbulence are modeled by two eddy viscosity models. High-Reynolds-number form of the k-epsilon model is coupled with a wall-function to avoid excessive refinement of the grid in the low-Reynolds number regions. The k-epsilon equations are solved by the explicit-implicit MacCormack method. The algebraic Baldwin-Lomax model is also being used as an inexpensive alternative for the cases which do not experience massive separation. Several examples of two-dimensional solutions are given to illustrate both wall and free turbulent shear flows which include fluid dynamic phenomena, such as shocks, boundary layers, shear layers, wakes, separations and recirculations. The results compared with experimental data show good agreeent.

Baysal, O.↗

NASA NTRS1987

Multistep modeling of protein structure: application towards refinement of tyr-tRNA synthetase

The scope of multistep modeling (MSM) is expanding by adding a least-squares minimization step in the procedure to fit backbone reconstruction consistent with a set of C-alpha coordinates. The analytical solution of Phi and Psi angles, that fits a C-alpha x-ray coordinate is used for tyr-tRNA synthetase. Phi and Psi angles for the region where the above mentioned method fails, are obtained by minimizing the difference in C-alpha distances between the computed model and the crystal structure in a least-squares sense. We present a stepwise application of this part of MSM to the determination of the complete backbone geometry of the 321 N terminal residues of tyrosine tRNA synthetase to a root mean square deviation of 0.47 angstroms from the crystallographic C-alpha coordinates.

NASA Discipline Exobiology↗

NASA NTRS1986

Simplified curve fits for the thermodynamic properties of equilibrium air

New improved curve fits for the thermodynamic properties of equilibrium air were developed. The curve fits are for p = p(e,rho), a = a(e,rho), T = T(e,rho), s = s(e,rho), T = T(p,rho), h = h(p,rho), rho = rho(p,s), e = e(p,s) and a = a(p,s). These curve fits can be readily incorporated into new or existing Computational Fluid Dynamics (CFD) codes if real-gas effects are desired. The curve fits were constructed using Grabau-type transition functions to model the thermodynamic surfaces in a piecewise manner. The accuracies and continuity of these curve fits are substantially improved over those of previous curve fits appearing in NASA CR-2470. These improvements were due to the incorporation of a small number of additional terms in the approximating polynomials and careful choices of the transition functions. The ranges of validity of the new curve fits are temperatures up to 25,000 K and densities from 10 to the minus 7th to 100 amagats (rho/rho sub 0).

Srinivasan, S.↗

NASA NTRS1986

A comparative study of prebiotic and present day translational models

It is generally recognized that the understanding of the molecular basis of primitive translation is a fundamental step in developing a theory of the origin of life. However, even in modern molecular biology, the mechanism for the decoding of messenger RNA triplet codons into an amino acid sequence of a protein on the ribosome is understood incompletely. Most of the proposed models for prebiotic translation lack, not only experimental support, but also a careful theoretical scrutiny of their compatibility with well understood stereochemical and energetic principles of nucleic acid structure, molecular recognition principles, and the chemistry of peptide bond formation. Present studies are concerned with comparative structural modelling and mechanistic simulation of the decoding apparatus ranging from those proposed for prebiotic conditions to the ones involved in modern biology. Any primitive decoding machinery based on nucleic acids and proteins, and most likely the modern day system, has to satisfy certain geometrical constraints. The charged amino acyl and the peptidyl termini of successive adaptors have to be adjacent in space in order to satisfy the stereochemical requirements for amide bond formation. Simultaneously, the same adaptors have to recognize successive codons on the messenger. This translational complex has to be realized by components that obey nucleic acid conformational principles, stabilities, and specificities. This generalized condition greatly restricts the number of acceptable adaptor structures.

Rein, R.↗

NASA NTRS1986

Multistep modeling (MSM) of biomolecular structure application to the A-G mispair in the B-DNA environment

A multistep modeling procedure has been evolved to study the structural changes introduced by lesions in DNA. We report here the change in the structure of regular B-DNA geometry due to the incorporation of Ganti-Aanti mispair in place of a regular G-C pair, preserving the helix continuity. The energetics of the structure so obtained is compared with the Ganti-Asyn configuration under similar constrained conditions. We present the methodology adopted and discuss the results.

Non-NASA Center↗

NASA NTRS1986

Multistep modeling of protein structure: application to bungarotoxin

Modelling of bungarotoxin in atomic details is presented in this article. The model-building procedure utilizes the low-resolution crystal coordinates of the c-alpha atoms of bungarotoxin, sequence homology within the neurotoxin family, as well as high-resolution x-ray diffraction data of cobratoxin and erabutoxin. Our model-building procedure involves: (a) principles of comparative modelling, (b) embedding procedures of distance geometry, and (c) use of molecular mechanics for optimizing packing. The model is not only consistent with the c-alpha coordinates of crystal structure, but also agrees with solution conformational features of the triple-stranded beta sheet as observed by NOE measurements.

NASA Discipline Exobiology↗

NASA NTRS1983

On long-wavelength magnetic anomalies over Indian region

A data set composed of vector magnetic measurements obtained by MAGSAT and very accurate altitude determinations made using Sun sensors and star cameras was used to obtain data for very quiet days over the Indian region at 10 S to 40 N and 60 E to 110 E in an effort to determine the validity of quantitative estimates made from aeromagnetic data obtained by removing the core field. To further account for the external effects, the ring current contributions estimated using both X and Z variations were subtracted from the observed values. Before this, the core contribution was eliminated through a spherical harmonic expansion with terms up to N=13. Analysis of the residual measurements using Fast Fourier techniques indicates that the anomalies contain substantial power for wavelengths of about 1500 kms. Because the ring current effect has a spatial structure of this dimension over India, efforts are being made to exactly eliminate these two interfering effects from the data.

Srinivasan, S.↗

NASA NTRS1983

Electrode kinetics of oxygen reduction - A theoretical and experimental analysis of the rotating ring-disc electrode method

In order to calculate most of the rate constants for the intermediate formation of H2O2 in the electroreduction of O2 to H2O, the theoretical treatments of the rotating ring-disc electrode method by Damjanovic et al. (1966, 1967), Bagotskii et al. (1968, 1969), and Wroblowa et al. (1976) are modified. Rotating ring-disc electrode experimental data obtained for O2 reduction in Pt in 0.55 M H2SO4 are used to illustrate the calculations of rate constants according to the above theoretical treatments. A simple reaction model as proposed by the first author is consistent with the experimental data. The results indicate that O2 (97 percent) reduces to H2O in a direct four-electron transfer reaction. The adsorption of O2 is probably the rate-determining step in the potential region more negative than 0.5 V vs. reversible hydrogen electrode.

Hsueh, K.-L.↗