Engineering Papers⌕ Search

Engineering topics

Srinivasan, R.

Publications and source records attributed to Srinivasan, R..

46 records · Page 3

Aerothermal modeling program, phase 1

The combustor performance submodels for complex flows are evaluated. The benchmark test cases for complex nonswirling flows are identified and analyzed. The introduction of swirl into the flow creates much faster mixing, caused by radial pressure gradients and increase in turbulence generation. These phenomena are more difficult to predict than the effects due to geometrical streamline curvatures, like the curved duct, and sudden expansion. Flow fields with swirl, both confined and unconfined are studied. The role of the dilution zone to achieve the turbine inlet radial profile plays an important part, therefore temperature field measurements were made in several idealized dilution zone configurations.

Srinivasan, R.↗

Experiments in dilution jet mixing

Experimental results are given on the mixing of a single row of jets with an isothermal mainstream in a straight duct, to include flow and geometric variations typical of combustion chambers in gas turbine engines. The principal conclusions reached from these experiments were: at constant momentum ratio, variations in density ratio have only a second-order effect on the profiles; a first-order approximation to the mixing of jets with a variable temperature mainstream can be obtained by superimposing the jets-in-an isothermal-crossflow and mainstream profiles; flow area convergence, especially injection-wall convergence, significantly improves the mixing; for opposed rows of jets, with the orifice centerlines in-line, the optimum ratio of orifice spacing to duct height is one half of the optimum value for single side injection at the same momentum ratio; and for opposed rows of jets, with the orifice centerlines staggered, the optimum ratio of orifice spacing to duct height is twice the optimum value for single side injection at the same momentum ratio.

Holdeman, J. D.↗

Experiments in dilution jet mixing

Experimental results are presented on the mixing of a single row of jets with an isothermal mainstream in a straight duct, with flow and geometric variations typical of combustion chambers in gas turbine engines included. It is found that at a constant momentum ratio, variations in the density ratio have only a second-order effect on the profiles. A first-order approximation to the mixing of jets with a variable temperature mainstream can, it is found, be obtained by superimposing the jets-in-an-isothermal-crossflow and mainstream profiles. Another finding is that the flow area convergence, especially injection-wall convergence, significantly improves the mixing. For opposed rows of jets with the orifice cone centerlines in-line, the optimum ratio of orifice spacing to duct height is determined to be 1/2 of the optimum value for single injection at the same momentum ratio. For opposed rows of jets with the orifice centerlines staggered, the optimum ratio of orifice spacing to duct height is found to be twice the optimum value for single side injection at the same momentum ratio.

Holdeman, J. D.↗

Simulation of cardiovascular response to acceleration stress following weightless exposure

Physiological adjustments taking place during space flight tend to reduce the tolerance of the crew to headward (+Gz) acceleration experienced during the reentry phase of the flight. This reduced tolerance to acceleration stress apparently arises from an adaptation to the microgravity environment of space, including a decrease in the total circulating blood volume. Countermeasures such as anti-g garments have long been known to improve the tolerance to headward g-force, but their effectiveness in space flight has not been fully evaluated. The simulation study presented in this paper is concerned with the response of the cardiovascular system to g-stress following cardiovascular deconditioning, resulting from exposure to weightlessness, or any of its ground-based experimental analogs. The results serve to demonstrate the utility of mathematical modeling and computer simulation for studying the causes of orthostatic intolerance and the remedial measures to lessen it.

Srinivasan, R.↗

Dilution Jet Mixing Program, phase 1

The effect of jet to mainstream density ratio, flow area convergence as encounted in transition sections, and nonuniform mainstream profile upstream of dilution orifices on the mixing of a row of jets with a confined cross flow was quantified. It is found that: (1) jet spreading rate in transverse direction is increased with increasing J, H/D and with decreasing S/D; (2) the density ratio has only a second order effect on the jet mixing characteristics for a constant momentum ratio; (3) the temperature distributions in the jet mixing region are strongly influenced by the undisturbed mainstream profile; (4) flow area convergence enhances mixing in radial and transverse directions. An asymmetric convergent duct with flat wall injection has the same jet mixing characteristics as a symmetric convergent duct. An asymmetric convergent duct with slant wall injection has a faster jet spreading rate in the transverse direction.

Srinivasan, R.↗

Numerical computations of swirling recirculating flow

Swirling, recirculating, nonreacting flows were computed using a 2D elliptic program consisting of three tasks. The computations in Task 1 and 2 were made using an independent analysis for the two coaxial swirling flows. The Task 2 computations were made using the measured profiles of the mixing region. In Task 3, a modified 2D elliptic program was employed to include the effects of interaction between the inner and outer streams.

Srinivasan, R.↗

Turbulent plane Couette flow using probability distribution functions

A numerical scheme employing a combination of the discrete ordinate method and finite differences is developed for solving the one-dimensional form of Lundgren's (1967) model equation for turbulent plane Couette flow. The approach used requires no a priori assumption about the form of the turbulent distribution function, and the numerical solution is obtained directly from the governing differential equations. Two different types of boundary conditions (zero-gradient and Chapman-Enskog) for the distribution function are evaluated by comparing the numerical results with experimental data. It is found that: (1) the present approach gives convergent and stable results over a wide range of Reynolds numbers; (2) Lundgren's equation yields results that compare well with experimental data for mean velocity and skin friction in the case of simple Couette flow; (3) the zero-gradient boundary condition leads to a logarithmic flow profile; and (4) the Chapman-Enskog boundary condition provides very good agreement with experimental data when applied within the near-wall region.

Srinivasan, R.↗

A study of turbulent flow between parallel plates by a statistical method

Turbulent Couette flow between parallel plates was studied from a statistical mechanics approach utilizing a model equation, similar to the Boltzmann equation of kinetic theory, which was proposed by Lundgren from the velocity distribution of fluid elements. Solutions to this equation are obtained numerically, employing the discrete ordinate method and finite differences. Two types of boundary conditions on the distribution function are considered, and the results of the calculations are compared to available experimental data. The research establishes that Lundgren's equation provides a very good description of turbulence for the flow situation considered and that it offers an analytical tool for further study of more complex turbulent flows. The present work also indicates that modelling of the boundary conditions is an area where further study is required.

Srinivasan, R.↗

High-speed leading edge problem.

The sharp leading edge problem has been studied for both monatomic and diatomic gases using the Boltzmann equation with the Bhatnagar-Gross-Krook type models as the governing equation and the discrete ordinate method with a closed-boundary value approach as a tool. Plate length relative to the freestream mean free path is taken to be 52. The gas-surface interaction law is assumed to be diffuse reflection. The local distribution functions of molecular velocities and internal energies (for the diatomic gas) for the entire flowfield have been calculated for a freestream Mach number of 6.1. Comparisons are made between the calculated results and experimental data.

Huang, A. B.↗