Synchrotron based investigation of anisotropy and microstructure of wire arc additive manufactured Grade 91 steel
Not Available
Robin, Ishtiaque K. (ORCID:0000000244670861)↗
Engineering topics
Sridharan, Niyanth
Publications and source records attributed to Sridharan, Niyanth.
Repairing High γ’ Hot Section Gas Turbine Components Using Advanced Manufacturing
This article describes the ability to use laser-blown powder deposition to repair high γ' IN-100 superalloy gas turbine components. The influence of various process conditions on the ability to make crack-free IN-100 deposits over surrogate high γ' alloys was investigated to identify cracking mechanisms in the deposit and heat-affected zones (HAZs). The various crack formation mechanisms, such as solidification cracking and liquation cracking, were evaluated using multiscale characterization and numerical simulation. The cracking in the deposit region was predominantly solidification cracking, while those observed in the HAZ were liquation cracking. The results showed that controlling thermally induced residual stresses is the key to eliminating cracking, and the optimum preheat temperature was determined. In conclusion, the results were then contrasted with those in published literature and an approach to effectively repair hot section parts was presented.
36 MATERIALS SCIENCE↗
Additive manufacturing methods using aluminum-rare earth alloys and products made using such methods
Described herein are additive manufacturing methods and products made using such methods. The alloy compositions described herein are specifically selected for the additive manufacturing methods and provide products that exhibit superior mechanical properties as compared to their cast counterparts. Using the compositions and methods described herein, products that do not exhibit substantial coarsening, such as at elevated temperatures, can be obtained. The products further exhibit uniform microstructures along the print axis, thus contributing to improved strength and performance. Additives also can be used in the alloys described herein.
Plotkowski, Alex J.↗
A Comparative Tribo-Mechanical Behavior Analysis of Laser Cladded Nitronic 60 Coating Against Wrought Nitronic 60 Alloy
In this study the tribological and mechanical behavior of a laser cladded Nitronic 60 coating on maraging steel is compared to that of a wrought Nitronic 60 alloy. A multi-layer Nitronic 60 coating was deposited using laser directed energy deposition, and its microstructure, porosity, and microhardness were characterized. The microhardness of the coated region in the laser cladded Nitronic 60 varied between 270-300 HV whereas that for wrought form was 230 HV. Controlled tribological tests under motor oil lubricated conditions were conducted at both room and elevated temperatures. The laser cladded Nitronic coating exhibited poorer wear resistance at room temperature but higher wear resistance at elevated temperature as compared to the wrought Nitronic alloy. Severe plastic deformation and fracture was observed on the laser cladded coating after the wear tests at both temperatures. Wear mechanisms were investigated based on the morphological and compositional characterization of the wear tracks.
36 MATERIALS SCIENCE↗
Effect of N 2 - and CO 2 -containing shielding gases on composition modification and carbonitride precipitation in wire arc additive manufactured grade 91 steel
Additive manufacturing (AM) represents a promising technique to fabricate metallic alloys with greater control of the resulting material features as compared to traditional manufacturing routes. Recently, there is greater interest in AM research on 9 wt% Cr ferritic/martensitic (F/M) steels, which are commonly studied for use in the nuclear energy industry. This work aims to prove that wire arc AM can manufacture F/M steels with adequate mechanical properties in multiple processing atmospheres and aims to study how shielding gas composition can be leveraged during fabrication to induce specific precipitation pathways. The effect of shielding gas composition on MX (M=Nb and/or V, Xdouble bondC and/or N) carbonitride precipitation in a 9 wt% Cr ferritic/martensitic (F/M) steel alloy known as Grade 91 was studied using N 2 and CO 2 gas additions to an inert Ar shielding gas atmosphere during wire arc AM. The N and C atoms present in the processing atmospheres were absorbed into the melt pools during fabrication. Due to their differing affinities for precipitate-forming reactions, the varying levels of C and N between the samples contributed to differences in final carbonitride composition and morphologies. Such precipitate behavior is of interest as carbonitrides have been shown to contribute to increased mechanical performance. This increased performance was studied via electron microscopy and tested for strength, ductility, and fracture properties.
36 MATERIALS SCIENCE↗
Benchmarking a 9Cr-2WVTa Reduced Activation Ferritic Martensitic Steel Fabricated via Additive Manufacturing
Reduced activation ferritic (RAF) martensitic steels are promising candidates for the first wall of fusion reactors. However, current manufacturing capabilities call for these components to be made by welding wrought plates. This limits design freedom and necessitates the use of post-weld heat treatments (PWHT) in accordance with the boiler and pressure vessel code. Additive manufacturing (AM) can offer a unique solution to solve this challenge by leveraging the layer-wise deposition strategy to come up with temper bead deposition techniques to eliminate post-processing heat treatments (PPHT). However, it is necessary to benchmark the properties of RAF steels fabricated by AM with their wrought counterparts to identify the process-structure-property correlation, which is the goal of this study. The study demonstrates that while tensile properties at room temperature and high temperatures are satisfactory, the as fabricated and samples after PPHT have significant heterogeneity in tensile elongation. This has been attributed to the presence of discontinuities in the build. The as-fabricated samples have an average tensile strength of 1190 + 12 MPa and an average elongation of 15 + 5% at room temperature and 658 ± 20 MPa ultimate tensile strength (UTS) and 14 ± 7% at 600 °C. After the post-weld heat treatment, mechanical properties decrease to around 600–650 MPa and an elongation between 20–25% at room temperature to 300 MPa UTS and 25–28% elongation at 600 °C. The characterization of microstructures at various length scales demonstrates that the as-fabricated structure has a significant fraction of delta ferrite in a lath martensitic matrix. No precipitates could be identified in the as-fabricated structure. PPHT led to a decrease in the area fraction of delta ferrite and precipitation of M 23 C 6 and MX. Detailed characterization clearly demonstrates that the lack of precipitates in the as-fabricated structure could be due to the slow tempering response of the alloy. Finally, the needs to develop new alloys to achieve the objectives stated above are articulated.
36 MATERIALS SCIENCE↗
Microchemical evolution of irradiated additive-manufactured HT9
The microstructural responses under 5 MeV Fe2 + single-ion-beam irradiation of three conditions of additive-manufactured (AM) HT9 steel using a powder-based directed energy deposition (DED) technique with and without postbuild heat treatments were investigated. Besides the observed dislocation loop formation and the absence of cavities at the irradiation condition of 50 dpa at 460 °C, Ni/Si/Mn-rich precipitates are found to form in all three conditions of AM-HT9, whereas Cu-rich clusters that arise from Cu uptake from the DED process are only observed in the heat-treated conditions, and not in the as-built (ASB) condition. Coprecipitation of the Cu- and Ni/Si/Mn-rich clusters occur near defect sinks such as line dislocations and grain boundaries in the heat-treated AM-HT9. The variation in microchemical evolution can be directly linked to the starting sink strength of the three AM-HT9 conditions, and the ASB condition with higher sink strength suppressed the responses observed in the postbuild heat-treated specimens.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Tailoring plasticity mechanisms in compositionally graded hierarchical steels fabricated using additive manufacturing
Abstract While there exists in nature abundant examples of materials with site-specific gradients in microstructures and properties, engineers and designers have traditionally used monolithic materials with discrete properties. Now, however, additive manufacturing (AM) offers the possibility of creating structures that mimic some aspects of nature. One example that has attracted attention in the recent years is the hierarchical structure in bamboo. The hierarchical architecture in bamboo is characterized by spatial gradients in properties and microstructures and is well suited to accommodate and survive complex stress states, severe mechanical forces, and large deformations. While AM has been used routinely to fabricate functionally graded materials, this study distinguishes itself by leveraging AM and physical metallurgy concepts to trigger cascading deformation in a single sample. Specifically, we have been successful in using AM to fabricate steel with unique spatial hierarchies in structure and property to emulate the structure and deformation mechanisms in natural materials. This study shows an improvement in the strength and ductility of the nature-inspired “hierarchical steel” compared with conventional cast stainless steels. In situ characterization proves that this improvement is due to the sequential activation of multiple deformation mechanisms namely twinning, transformation-induced plasticity, and dislocation-based plasticity. While significantly higher strengths can be achieved by refining the chemical and processing technique, this study sets the stage to achieve the paradigm of using AM to fabricate structures which emulate the flexibility in mechanical properties of natural materials and are able to adapt to in-service conditions.
36 MATERIALS SCIENCE↗
Microstructure and mechanical properties of high Mn-containing ferritic-martensitic alloys exposed to cyclical thermal treatment
Substantial residual tensile stress tends to accumulate in currently available high-Cr ferritic martensitic steels that are subjected to cyclical heat treatment, which leads to premature brittle fracture. By tailoring the alloy composition, this thermal cycling can be exploited to induce a high number density of nanoprecipitates and phase transformations countering residual tensile stresses. In this work, three new variants of ferritic-martensitic steels have been designed with computational thermodynamics to meet the goals of mitigating residual tensile stresses by lowering martensite start temperatures and of enhancing mechanical strength and irradiation sink strength by increasing the number density of nanoprecipitates. Furthermore, ctenast materials were subjected to cyclical heat treatment. The thermally cycled samples were evaluated with mechanical testing and microstructural analysis to identify the optimal composition in which figures of merit include low residual stress and a high density of nanoscale MX (M = metal, X = C/N) precipitates, leading to high yield strength with reasonable ductility. The noticeably higher density of nanoprecipitates in the optimal alloy favor its higher yield strength, which is supported by the microstructure-derived yield strength calculation and precipitation kinetics simulation.
36 MATERIALS SCIENCE↗
Interdiffusion of Elements During Ultrasonic Additive Manufacturing
In this paper, we report evidence for enhanced elemental interdiffusion during ultrasonic additive manufacturing (UAM) across metal boundaries of copper-aluminum, nickel-gold, and nickel-gold-aluminum. The high solute interdiffusion measured by energy dispersive X-ray spectroscopy line scans is rationalized with calculated vacancy concentrations orders of magnitude larger than thermal equilibrium values. The above estimates are supported by existing knowledge related to defect physics and UAM thermal cycles. The observation of pronounced elemental mixing are evidence for the presence of enhanced non-equilibrium immiscible metal interdiffusion during UAM processing.
36 MATERIALS SCIENCE↗
Consumable development to tailor residual stress in parts fabricated using directed energy deposition processes
Distortion and residual stresses are major challenges that limit the ability to fabricate large scale structures using Additive Manufacturing (AM). Researchers worldwide are evaluating techniques to induce compressive residual stress in the parts via intermittent rolling. While reasonable success has been documented, the idea of lowering the martensite start temperature to induce compressive stresses has not been evaluated in the context of AM, despite demonstrated success by the welding community. This study validates the hypothesis that, by a proper selection of materials and process parameters, one may effectively reduce distortion and induce a compressive residual stress in AM parts. Using neutron diffraction to measure residual stresses in parts, we demonstrate that, in addition to selection of the correct materials, the inter pass temperature plays a major role in controlling the residual stress evolution. The observations relating to the residual stresses are rationalized based on a microstructural evolution in these samples. Based on this preliminary study, a strategy to fabricate large structures with minimal distortion and residual stress is outlined.
36 MATERIALS SCIENCE↗
Microstructures and mechanical properties of a modified 9Cr ferritic-martensitic steel in the as-built condition after additive manufacturing
A newly developed nano-structured high-Mn 9Cr ferritic-martensitic (FM) steel designed for additive manufacturing (Additive-manufactured Nanostructured Alloy, ANA) was fabricated via the direct energy deposition method. The as-printed ANA2 showed tensile properties (strength and elongation) and Charpy impact toughness (upper-shelf energy and ductile-brittle transition temperature) comparable to oxide-dispersion-strengthened (ODS) Eurofer and PM2000. Compared with wrought P91, the as-built ANA2 showed significantly higher yield strength but inferior Charpy impact toughness and ductility. Microstructural characterization revealed uniformly distributed sub-micron pores, an extremely high dislocation density, and a high density of ultrafine nano-structured precipitates in the matrix. The microstructures indicated the dislocations as the dominant strengthening element and the ultrafine precipitates as the primary contribution to estimated irradiation sink density. This work demonstrates the ability to exploit the unique consolidation properties of additive manufacturing to fabricate steels which marry the benefits of both ODS alloys and conventionally processed FM steels.
36 MATERIALS SCIENCE↗
Mitigating Scatter in Mechanical Properties in AISI 410 Fabricated via Arc-Based Additive Manufacturing Process
Wire-based metal additive manufacturing utilizes the ability of additive manufacturing to fabricate complex geometries with high deposition rates (above 7 kg/h), thus finding applications in the fabrication of large-scale components, such as stamping dies. Traditionally, the workhorse materials for stamping dies have been martensitic steels. However, the complex thermal gyrations induced during additive manufacturing can cause the evolution of an inhomogeneous microstructure, which leads to a significant scatter in the mechanical properties, especially the toughness. Therefore, to understand these phenomena, arc-based additive AISI 410 samples were fabricated using robotic gas metal arc welding (GMAW) and were subjected to a detailed characterization campaign. The results show significant scatter in the tensile properties as well as Charpy V-notch impact toughness data, which was then correlated to the microstructural heterogeneity and delta (δ) ferrite formation. Post-processing (austenitizing and tempering) treatments were developed and an ~70% reduction in the scatter of tensile data and a four-times improvement in the toughness were obtained. The changes in mechanical properties were rationalized based on the microstructure evolution during additive manufacturing. Based on these, an outline to tailor the composition of “printable” steels for tooling with isotropic and uniform mechanical properties is presented and discussed.
36 MATERIALS SCIENCE↗
In situ measurement of phase transformations and residual stress evolution during welding using spatially distributed fiber-optic strain sensors
Welding of high-strength steels can result in large tensile strains as the base metal and filler material cool from their molten state. To combat these large tensile strains, low-transformation-temperature (LTT) metal fillers have been proposed. These fillers undergo a martensitic phase transformation at a lower temperature which can ultimately reduce the tensile strain or can even introduce compressive strain adjacent to the weld metal. However, the process for optimizing the composition of the LTT material, as well as various weld parameters for each unique weld geometry, can be quite expensive, especially if the acceptance criterion requires using neutrons, x-ray beams, or destructive techniques to characterize residual stresses. This work describes a simple, low-cost method for quantifying residual stresses and phase transformations in situ during welding. Spatially distributed fiber-optic sensors were bonded to a cast iron plate, along with tack-welded thermocouples, to measure temperature and strain during multiple passes with LTT filler metals. Results show that the fiber-optic sensors can successfully resolve compressive strain adjacent to the weld region caused by the martensitic phase transformations in the LTT filler material.
47 OTHER INSTRUMENTATION↗
Additive manufacturing methods using aluminum-rare earth alloys and products made using such methods
Described herein are additive manufacturing methods and products made using such methods. The alloy compositions described herein are specifically selected for the additive manufacturing methods and provide products that exhibit superior mechanical properties as compared to their cast counterparts. Using the compositions and methods described herein, products that do not exhibit substantial coarsening, such as at elevated temperatures, can be obtained. The products further exhibit uniform microstructures along the print axis, thus contributing to improved strength and performance. Additives also can be used in the alloys described herein.
36 MATERIALS SCIENCE↗