Engineering topics

Spong, Donald A.

Publications and source records attributed to Spong, Donald A..

11 records

DOE OSTI2024

Orbit-following simulations of fast-ion transport and losses due to the Alfvén eigenmode burst in the Large Helical Device

Orbit-following simulations of fast-ion transport and losses with time-dependent electromagnetic perturbations are performed to clarify the roles of Alfvén eigenmodes (AEs) and the low-frequency magnetohydrodynamic (MHD) mode observed in the kinetic-MHD hybrid simulation of AE bursts in the Large Helical Device. Fast-ion pressure profile flattening in the kinetic-MHD hybrid simulation can be reproduced by an orbit-following simulation with only the primary single AE of the time-dependent amplitude following the kinetic-MHD hybrid simulation result, while orbit-following simulations with constant AE amplitude of average level during AE burst cannot reproduce the fast-ion pressure profile flattening observed. The effects of other modes are negligible on the fast-ion pressure profile flattening. The fast-ion losses in kinetic-MHD hybrid simulation can be reproduced by an orbit-following simulation with time-dependent amplitude when the low-frequency MHD mode is considered in addition to multiple AEs. This indicates the synergetic effect of multiple AEs and the low-frequency MHD mode on fast-ion losses.

Seki, Ryohsuke↗

DOE OSTI2024

MHD stability trends and improved performance of LHD inward-shifted configurations: The role of the neutral beam current drive and thermal plasma density

The aim of the present study is to analyze the effect of the neutral beam current drive (NBCD), thermal plasma density, and NBI operational regime on the stability of pressure gradient-driven modes (PGDM) and Alfvén eigenmodes (AE) in LHD inward-shifted configurations. The stabilization of n/m = 1/2 PGDM (n toroidal mode and m poloidal mode) is observed in the discharge 167 800 during the co-NBCD phase. The iota profile evolution measured by motional stark effect diagnostic may indicate the iota profile up-shift caused by the co-NBCD can induce a non-resonant transition of the rational surface 1/2 before the mode stabilization. The evolution of the iota profile and continuum gaps in the discharge 167 805 during the ctr-NBCD phase leads to the stabilization of the AE, caused by the narrowing of the continuum gap as the iota profile down-shift. Opposite stability trends are identified for PGDM and AE stability with respect to the thermal plasma density. A larger thermal plasma density (larger thermal β) further enhances PGDM although the continuum gaps are narrower leading to configurations with stable AEs. The linear stability of AEs is analyzed using the gyro-fluid FAR3d code to reproduce the AE stability trends observed in the experiments with respect to the NBCD and thermal plasma density. The analysis of hypothetical scenarios dedicated to study different NBI operational regimes with respect to EP energy, and β and radial density profiles indicate off-axis NBI operation shows a higher EP β threshold to destabilize AEs compared to on-axis configuration. This is explained by the presence of a TAE gap in the inner plasma region, easily destabilized by an on-axis NBI injection. The control of the NBCD and thermal plasma in the discharge 167 800 shows a transitory stabilization of PGDM and AEs, as well as an improved discharge performance identified by an increment of the neutron fluxes.

Varela, Jacobo↗

DOE OSTI2024

Modeling of frequency-sweeping Alfvén modes in the TJ-II stellarator

Alfvénic activity has been observed in the TJ-II stellarator which resembles the frequency sweeping demonstrated by Alfvén cascade modes in tokamaks. A numerical validation study was conducted using a reduced magnetohydrodynamic (MHD) model to show that such modes could only have been observed in discharges where the rotational transform profile was non-monotonic. During experiments, coil current was varied which resulted in shifting of the minimum value of the rotational transform profile. To mimic this effect, we study the Alfvénic activity predicted by the reduced MHD model for a set of input rotational transform profiles with varying minima. A mode is found whose toroidal and poloidal mode numbers match those predicted in experiments which sweeps downward/upward in frequency as the minimum value of the rotational transform profile is increased/decreased. The results serve as a demonstration of the validity and utility of MHD spectroscopy.

Alfvén cascades↗

DOE OSTI2023

Analysis of beam ion driven Alfvén eigenmode stability induced by Tungsten contamination in EAST

Alfvén eigenmodes (AE) activity is observed in the EAST high β N and low B T discharge 93910, operation scenario dedicated to explore the ITER baseline scenario. AEs are triggered after the plasma is contaminated by Tungsten that causes an abrupt variation of the thermal plasma and energetic particles (EPs) profiles. The aim of the present study is to analyze the AE stability in the 93910 discharge using the gyro-fluid code FAR3d, identifying the AE stability trends by comparing the plasma before and after the Tungsten contamination. Tungsten contamination causes the destabilization of Toroidal AEs (TAE) and Energetic particle modes (EPMs) in the same frequency range and radial location with respect to the experimental observation and M3D-K/GTAW code results. Next, a set of parametric studies are performed to analyze the effect of the thermal plasma and EP parameters on the AE stability. The analysis indicates a lower EP β threshold for the AEs destabilization if the EP energy increases, an improved AE stability of on-axis NBI configurations due to the stronger continuum damping in the inner plasma region as well as a large enhancement of the EP drive as the thermal ion density increases due to a higher ratio of the EP and Alfven velocities. Consequently, the simulations indicate the increment of the thermal ion density after the Tungsten contamination could be the main cause of the AE/EPM destabilization.

AE↗

DOE OSTI2023

Effect of the neutral beam injector operational regime on the Alfven eigenmode saturation phase in DIII-D plasma

The aim of this study is to analyze the effect of the neutral beam injector (NBI) operation regime on the saturation phase of the Alfven Eigenmodes (AEs) in DIII-D plasma. Here, the analysis is done using the linear and nonlinear versions of the gyro-fluid code FAR3d. A set of parametric analyses are performed modifying the nonlinear simulation EP $β$ (NBI injection power), EP energy (NBI voltage) and the radial location of the EP density profile gradient (NBI radial deposition). The analysis indicates a transition from the soft (local plasma relaxation) to the hard MHD (global plasma relaxation) limit if the simulation EP $β$ $\unicode{x2A7E}$ $0.02$, leading to bursting MHD activity caused by radial AEs overlapping. MHD bursts cause an enhancement of the EP transport showing ballistic-like features as avalanche-like events. Simulations in the soft MHD limit show an increment of the EP density gradient as the EP $β$ increases. On the other hand, there is a gradient upper limit in the hard MHD limit, consistent with the critical-gradient behavior. AEs induce shear flows and zonal current leading to the deformation of the flux surfaces and the safety factor profile, respectively, particularly strong for the simulation in the hard MHD limit. Simulations in the hard MHD regime show a decrease of the AE frequency in the saturation phase; this is caused by the destabilization of a transitional mode between a $9/3-10/3$ TAE and a $9/3$ RSAE that may explain the AE frequency down-sweeping observed in some DIII-D discharges. Reducing the EP energy in the nonlinear simulations leads to a weakening of the plasma perturbation. On the other hand, increasing the EP energy causes the opposite effect. Nonlinear simulations of off-axis NBI profiles indicate a lower plasma perturbation as the EP density gradient is located further away from the magnetic axis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Simulation of the TAEs’ saturation phase in the Large Helical Device: MHD burst

Here, the aim of the present study is to analyze the saturation regime of the toroidal Alfven eigenmodes (TAE) in the Large Helical Device plasma, particularly the MHD burst. The linear and nonlinear evolution of the TAEs are simulated by the FAR3d code that uses a reduced MHD model for the thermal plasma coupled with a gyrofluid model for the energetic particle (EP) species. The linear simulations indicate the overlapping of 1/2–1/1, 2/3–2/4 and 3/5–3/6 TAEs in the inner-middle plasma region and frequency range of 45–75 kHz, triggered by EPs with an energy of T f = 45 keV and EP β = 0.022. The nonlinear simulations show that 2/3–2/4 and 3/4–3/5 TAEs are further destabilized due to the energy transfer from the 1/1–1/2 TAE, leading to broad TAE radial overlapping and triggering of the MHD burst. The energy of the 1/1–1/2 TAE is also nonlinearly transferred to the thermal plasma destabilizing the 0/0 and 0/1 modes, inducing the generation of shear flows and zonal currents, as well as large deformations in the thermal pressure and EP density radial profiles. The nonlinear simulation reproduces the same succession of instabilities and the same frequency range with respect to the experiment. The instability propagates outward during the bursting phase, showing a large decrease of the EP density profile between the middle-outer plasma, indicating the loss of part of the EP population that explains the decrease in the plasma heating efficiency observed during the MHD burst.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Theoretical study of the Alfven eigenmode stability in CFETR steady state discharges

The aim of this study is to analyze the stability of Alfven eigenmodes (AE) in the China Fusion Engineering Test Reactor (CFETR) plasma for steady state operations. The analysis is done using the gyro-fluid code FAR3d including the effect of the acoustic modes, EP finite Larmor radius damping effects and multiple energetic particle populations. Two high poloidal β scenarios are studied with respect to the location of the internal transport barrier (ITB) at r/a ≈ 0.45 (case A) and r/a ≈ 0.6 (case B). Both operation scenarios show a narrow TAE gap between the inner-middle plasma region and a wide EAE gap all along the plasma radius. In this work, the AE stability of CFETR plasmas improves if the ITB is located inwards, case A, showing AEs with lower growth rates with respect to the case B. The AEs growth rate is smaller in the case A because the modes are located in the inner-middle plasma region where the stabilizing effect of the magnetic shear is stronger with respect to the case B. Multiple EP populations effects (NBI driven EP + alpha articles) are negligible for the case A, although the simulations for the case B show a stabilizing effect of the NBI EP on the n = 1 BAE caused by α particles during the thermalization process. If the FLR damping effects are included in the simulations, the growth rate of the EAE/NAE decreases up to 70%, particularly for n > 3 toroidal families. Low n AEs (n < 6) show the largest growth rates. On the other hand, high n modes (n = 6 to 15) are triggered in the frequency range of the NAE, strongly damped by the FLR effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Theoretical analysis of the saturation phase of the 1/1 energetic-ion-driven resistive interchange mode

The aim of the present study is to analyze the saturation regime of the energetic-ion-driven resistive interchange mode (EIC) in the LHD plasma. In this work, a set of nonlinear simulations are performed by the FAR3d code that uses a reduced MHD model for the thermal plasma coupled with a gyrofluid model for the energetic particle (EP) species. The hellically trapped EP component is introduced through a modification of the averaged drift velocity operator to include their precessional drift. The nonlinear simulation results show similar 1/1 EIC saturation phases with respect to the experimental observations, reproducing the enhancement of the n/m = 1/1 resistive interchange modes (RIC) amplitude and width as the EP β increases, the EP β threshold for the 1/1 EIC excitation, the further destabilization of the 1/1 EIC as the population of the helically trapped EP increases and the triggering of burst events. The frequency of the 1/1 EIC calculated during the burst event is 9.4 kHz and the 2/2 and 3/3 overtones are destabilized, consistent with the frequency range and the complex mode structure measured in the experiment. In addition, the simulation shows the inward propagation of the 1/1 EIC due to the nonlinear destabilization of the 3/4 and 2/3 energetic particle modes, leading to the partial overlapping between resonances during the burst event. Finally, the analysis of the 1/1 EIC stabilization phase shows the excitation of the 1/1 RIC as soon as the flattening induced by the 1/1 EIC in the pressure profile vanishes, leading to the retrieval of the pressure gradient at the plasma periphery and the overcoming of the RIC stability limit.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

A novel path to runaway electron mitigation via deuterium injection and current-driven MHD instability

Relativistic electron (RE) beams at high current density (low safety factor, qa) yet very low free-electron density accessed with D2 secondary injection in the DIII-D and JET tokamak are found to exhibit large-scale MHD instabilities that benignly terminate the RE beam. In JET, this technique has enabled termination of MA-level RE currents without measurable first-wall heating. This scenario thus offers an unexpected alternate pathway to achieve RE mitigation without collisional dissipation. Benign termination is explained by two synergistic effects. First, during the MHD-driven RE loss events both experiment and MHD orbit-loss modeling supports a significant increase in the wetted area of the RE loss. Second, as previously identified at JET and DIII-D, the fast kink loss timescale precludes RE beam regeneration and the resulting dangerous conversion of magnetic to RE kinetic energy. During the termination, the RE kinetic energy is lost to the wall, but the current fully transfers to the cold bulk thus enabling benign Ohmic dissipation of the magnetic energy on longer timescales via a conventional current quench. Hydrogenic (D2) secondary injection is found to be the only injected species that enables access to the benign termination. D2 injection: 1) facilitates access to low qa in existing devices (via reduced collisionality & resistivity), 2) minimizes the RE avalanche by ‘purging’ the high-Z atoms from the RE beam, 3) drives recombination of the background plasma, reducing the density and Alfven time, thus accelerating the MHD growth. Furthermore, this phenomenon is found to be accessible when crossing the low qa stability boundary with rising current, falling toroidal field, or contracting minor radius - the latter being the expected scenario for vertically unstable RE beams in ITER. While unexpected, this path scales favorably to fusion-grade tokamaks and offers a novel RE mitigation scenario in principle accessible with the day-one disruption mitigation system (DMS) of ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Isotope dependence of beta-induced Alfvén eigenmode (BAE) and low frequency mode (LFM) stability in DIII-D

The stability of beta-induced Alfvén eigenmodes (BAE) and the low frequency modes (LFMs) that were formerly called beta-induced Alfvén-acoustic eigenmodes is discussed. Here, after a brief summary of previous publications on the stability in DIII-D beam-heated, reversed-shear, deuterium plasmas with deuterium neutral beam injection (NBI), new observations in mixed hydrogen and deuterium plasmas are reported. With deuterium NBI, BAEs are at least as unstable in mixed-species plasmas as in deuterium plasmas; however, with hydrogen NBI, the BAEs are stable. In contrast, the LFMs are unaffected by changes in beam species, consistent with the previous observation that LFMs are not driven by high-energy beam ions. As predicted by theory, the LFMs appear more unstable in mixed species plasmas than in pure deuterium discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

"BAAE" instabilities observed without fast ion drive

The instability that was previously identified as a fast-ion driven beta-induced Alfv´en-acoustic eigenmode (BAAE) in DIII-D was misidentified. In a dedicated experiment, low frequency modes (LFM) with characteristic “Christmas light” patterns of brief instability linked to the safety factor evolution occur in plasmas with electron temperature T e ≳ 2.1 keV but modest beta. To isolate the importance of different driving gradients on these modes, the electron cyclotron heating power and 80 keV, sub-Alfv´enic neutral beams are altered for 50-100 ms durations in reproducible discharges. Although beta-induced Alfv´en eigenmodes and reversed-shear Alfv´en eigenmodes stabilize when beam injection ceases (as expected for a fast-ion driven instability), the low frequency modes that were called BAAEs persist. Data mining reveals that characteristic LFM instabilities can occur in discharges with no beam heating but strong electron cyclotron heating. A large database of over 1000 discharges shows that LFMs are only unstable in plasmas with hot electrons but modest overall beta. The experimental LFMs have low frequencies (comparable to diamagnetic drift frequencies) in the plasma frame, occur near the minimum of the safety factor q min , and appear when q min is close to rational values. In conclusion, theoretical analysis suggests that the LFMs are a low frequency reactive instability of predominately Alfv´enic polarization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗