Engineering Papers⌕ Search

Engineering topics

Sperber, B. R.

Publications and source records attributed to Sperber, B. R..

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

SPS large array simulation

Three types of computer simulations were developed to study the SPS microwave power transmission system (MPTS). The radially symmetric array simulation is low cost and is utilized to investigate general overall characteristics of the spacetenna at the array level only. "Tiltmain", a subarray level simulation program, is used to study the effects of system errors which modify the far-field pattern. The most recently designed program, "Modmain," takes the detail of simulation down to the RF module level and so to date is the closest numerical model of the reference design.

Rathjen, S.↗
NASA NTRS1980

SPS phase control studies

To properly point and form the satellite microwave power beam, the outputs of the power amplifiers in the transmitting array must be phased in a specific and coherent fashion. A retrodirective CW phase conjugating system using a spread spectrum uplink signal and a reference phase signal that is distributed via fiber optics, was selected as the control system for SPS. The design details are presented and applications of the system are discussed.

Lund, W. W.↗
NASA NTRS1980

Modified Reference SPS with Solid State Transmitting Antenna

The development of solid state microwave power amplifiers for a solar power satellite transmitting antenna is discussed. State-of-the-art power-added efficiency, gain, and single device power of various microwave solid state devices are compared. The GaAs field effect transistors and the Si-bipolar transistors appear potentially feasible for solar power satellite use. The integration of solid state devices into antenna array elements is examined and issues concerning antenna integration and consequent satellite configurations are examined.

Woodcock, G. R.↗
NASA NTRS1980

Prototype solar power satellite options

The choice of options for the prototype solar power satellite is addressed relative to risk and cost. Emphasis is placed on the reduction of the risk of failure. Risk is the program cost multiplied by the reduction in probability of program success due to the risky action. Four classes of risk are identified. It is suggested that prototyping would reduce the technical risk as well as reduce the effects of the other three types of risk by allowing them to be quantified earlier. Prototype demonstration requirements addressed include electromagnetic power link feasibility demonstration, component integration verification, construction technology verification, and cost performance verification. Specific prototype requirements are listed and prototyping options are given in tabular form.

Sperber, B. R.↗
NASA NTRS1980

High-power microwave optics for flexible power transmission systems

A large concave microwave mirror near the transmitter can magnify the apparent size of the Earth as seen from a phased array, and vice versa, permitting a small phased array to be coupled to a small rectenna while preserving the transmission efficiency (the reflection loss is slight) and peak power densities characteristic of the reference system. This augmentation of the phased array aperture with a large mirror gives the system greater resolution (in the optical sense), and opens new degrees of freedom in SPS design. The consequences of such an approach for a prototype satellite were explored. Its consequences for a mature SPS are discussed.

Drexler, K. E.↗
NASA NTRS1980

Characterization of reflected light from the space power system

Sunlight reflected off large space structures is examined. To assure that this illumination does not exceed the irradiance tolerances of the eye, reflections from these satellites must be controlled by vehicle orientation and surface specifications. The components of various space power system vehicles to determine the reflectances which will significantly contribute to the ground illumination are evaluated. Calculations of reflected solar intensity from various satellite system elements requires description of the elements and of the geometry potential reflectance paths. Surface intensity and the conditions under which it will illuminate a portion of the Earth are also determined.

Liemohn, H. B.↗
NASA NTRS1980

SPS large array simulation

The computer programming efforts were directed primarily to beam pattern analysis. The computer programs used for simulation provide: verification of the reference design; definition of feasible departures such as quantized distributions; the study of far-out sidelobe roll-off characteristics; the analysis of errors and failures; illumination function analysis to develop beam patterns for efficient collection; and beam shaping synthesis to meet environmental constraints.

Rathjen, S.↗
NASA NTRS1980

SPS phase control studies

To properly point and form the SPS microwave power beam, the outputs of the power amplifiers in the transmitting array must be phased in a specific and coherent fashion. The purpose of the SPB phase control system is to bring this about reliably. A number of different phase control schemes were studied. The one selected for the SPS baseline system is a retrodirective CW phase that is distributed via fiber optics. The basis of this selection is relative technical simplicity and requisite assurance of success.

Lund, W. W.↗
NASA NTRS1980

Modified reference SPS with solid state transmitting antenna

The motivations for considering solid state microwave power amplifiers for the solar power satellite transmitting antenna are the possibilities of greatly increased system reliability due to elimination of electron tube cathodes, a lower mass per unit power and transmitting array area due to the high power densities obtainable in semiconductors, and, probably, cost savings due to development of small hardware items that can be handled by individuals instead of organizations. In order to provide a fair assessment where we stand today with regard to solid state SPS technology, the design described here is close to that of the NASA/DOE reference and is implemented using today's solid state technology with only a small "push". The small push is raising the efficiency of DC-RF conversion from the .68 obtained by RCA in 1975 to somewhat over .8 of the solid state SPS. This is generally considered feasible by semiconductor industry representatives. Other solid state SPS configurations can yield somewhat better performance. However, these generally do not provide as fair a vehicle for comparison with the reference and usually also incorporate somewhat more advanced technologies.

Woodcock, G. R.↗
NASA NTRS1979

Applicability of solid state microwave technology to solar power satellites

A potential SPS design using antenna mounted GaAs FET's as the basic dc-RF converter is described, together with the rationale of why such a design may represent a viable cost effective complement to current SPS designs using tube type dc-RF converters such as klystrons or crossed field amplifiers. An initial description of a microwave antenna array module is given, together with a concept of how such a module is to be integrated into the SPS overall design. A comparison is made of several such designs using either antenna mounted or solar cell mounted dc-RF converters.

Nalos, E. J.↗