Engineering Papers⌕ Search

Engineering topics

Sorensen, N. E.

Publications and source records attributed to Sorensen, N. E..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Aircraft engine nozzle

A variable area exit nozzle arrangement for an aircraft engine was a substantially reduced length and weight which comprises a number of longitudinally movable radial vanes and a number of fixed radial vanes. The movable radial vanes are alternately disposed with respect to the fixed radial vanes. A means is provided for displacing the movable vanes along the longitudinal axis of the engine relative to the fixed radial vanes which extend across the main exhaust flow of the engine.

Sorensen, N. E.↗
NASA NTRS1977

Jet engine air intake system

An axisymmetric air intake system for a jet aircraft engine comprising a fixed cowl extending outwardly from the face of the engine, a centerbody coaxially disposed within the cowl, and an actuator for axially displacing the centerbody within the cowl was developed. The cowl and centerbody define a main airflow passageway therebetween, the configuration of which is changed by displacement of the centerbody. The centerbody includes a forwardly-located closeable air inlet which communicates with a centerbody auxiliary airflow passageway to provide auxiliary airflow to the engine. In one embodiment, a system for opening and closing the centerbody air inlet is provided by a dual-member centerbody, the forward member of which may be displaced axially with respect to the aft member.

Sorensen, N. E.↗
NASA NTRS1977

Transonic performance of an auxiliary airflow system for axisymmetric inlets

A large-scale model of an axisymmetric inlet with a centerbody auxiliary airflow system has been tested in the wind tunnel at transonic speeds. The auxiliary system allows additional airflow (other than in the main duct formed by the cowl and translating centerbody) to pass through the centerbody of the inlet and combine with the main duct airflow on its way to the engine face. The results of the tests are presented, and the inlet performance is compared to a closely related alternative inlet with a 'traveling' boundary-layer bleed system which precludes the use of a centerbody auxiliary airflow system. The comparison shows that the auxiliary airflow inlet can supply 7.7% more engine face airflow at Mach number 1.0 and is 26% shorter than the traveling bleed inlet. Even though maximum transonic airflow was not achieved at a comparable engine face mass-flow ratio of 0.580, a total-pressure distortion of 0.10 and a total-pressure recovery of 0.985 were achieved for the auxiliary airflow inlet while a recovery of only 0.965 was achieved for the traveling bleed inlet.

Sorensen, N. E.↗
NASA NTRS1976

Advanced porous transonic wind-tunnel nozzles

Advances in the design and control of the porous bleed flow distribution along the nozzle walls solves the problem of nonuniform flow at off-design conditions. This is accomplished in a two dimensional nozzle with porous parallel sidewalls backed with a single plenum chamber and employing a sliding compartment wall or backed with multiple plenum chambers within which the pressure can be controlled.

Sorensen, N. E.↗
NASA NTRS1976

Study of two axisymmetric inlets designed for Mach 3.5

Results from wind-tunnel tests of two large-scale models of axisymmetric mixed-compression inlet systems designed for Mach number 3.5 are compared. One inlet incorporated a 'traveling'-bleed system in an effort to achieve maximum transonic engine airflow supply. The other inlet required only a 'fixed'-bleed system, but had 21 percent less transonic airflow supply. The inlet with fixed bleed appears more attractive, if auxiliary airflow systems are used to increase the transonic airflow supply, because it can be 45 percent shorter and would be considerably lighter than the traveling-bleed inlet. In addition, the fixed-bleed inlet offers more operating-control margin at supersonic Mach numbers when the inlet is started. Further, its off-design performance is higher because separation of the flow in the subsonic diffuser can be avoided - something that apparently cannot be done with a traveling-bleed inlet without reducing the transonic airflow supply. Finally, it appears that the management and efficiency of bleed airflow for the fixed-bleed inlet can be improved using analytical methods verified by the tests.

Sorensen, N. E.↗
NASA NTRS1975

Supersonic inlet contour interpolation

A method for designing supersonic inlet contours is described which consists in the interpolation of the contours of two known inlets designed for different Mach numbers, thereby determining the contours for a third inlet at an intermediate design Mach number. Several similar axisymmetric inlet contours were interpolated from known inlets with design Mach numbers ranging from 2.16 to 4.0 and with design Mach numbers differing by as much as 1.0. The flowfields were calculated according to Sorensen's (1965) computer program. Shockwave structure and pressure distribution characteristics are shown for the interpolated inlets. The validity of the interpolation is demonstrated by comparing the plots of the flowfield properties across the throat station of the interpolated inlet with the known inlets which were designed iteratively. It seems possible to write a computer program so that a matrix of known inlet contours can be interpolated.

Sorensen, N. E.↗
NASA NTRS1974

Wind tunnel flow generation section

A flow generation section for a wind tunnel test facility is described which provides a uniform flow for the wind tunnel test section over a range of different flow velocities. The throat of the flow generation section includes a pair of opposed boundary walls which are porous to the flowing medium in order to provide an increase of velocity by expansion. A plenum chamber is associated with the exterior side of each of such porous walls to separate the same from ambient pressure. A suction manifold is connected by suction lines with each one of the chambers. Valves are positioned in each of the lines to enable the suction manifold to be independently varied.

Sorensen, N. E.↗
NASA NTRS1974

Variable geometry for supersonic mixed-compression inlets

Study of two-dimensional and axisymmetric supersonic mixed-compression inlet systems has shown that the geometry of both systems can be varied to provide adequate transonic airflow to satisfy the airflow demand of most jet engines. Collapsing geometry systems for both types of inlet systems provide a generous amount of transonic airflow for any design Mach number inlet system. However, the mechanical practicality of collapsing centerbodies for axisymmetric inlet systems is doubtful. Therefore, translating centerbody axisymmetric inlets with auxiliary airflow systems to augment the transonic airflow capability are an attractive alternative. Estimates show that the capture mass-flow ratio at Mach number 1.0 can be increased approximately 0.20 for a very short axisymmetric inlet system designed for Mach number 2.37. With this increase in mass-flow ratio, even variable-cycle engine transonic airflow demand can be matched without oversizing the inlet at the design Mach number.

Sorensen, N. E.↗
NASA NTRS1973

Possibilities for improved supersonic inlet performance

The results from detailed large-scale inlet tests were examined to assess the penalties, in terms of vehicle cruise range, for boundary-layer bleed, less than ideal engine-face pressure recovery, inlet weight, and external cowl drag. The assessment suggested specific improvements in the design of the inlet system that may increase the range of a typical supersonic transport approximately 6.9%. While no single design improvement can account for a large increase in range, careful attention to each design detail can yield a substantial total improvement. Because of noise considerations, future engines for advanced supersonic transports may be approximately 50% larger than used for the present study, making the effects of improved inlet performance even more important.

Sorensen, N. E.↗
NASA NTRS1973

Analytic and experimental performance of two isentropic mixed compression axisymmetric inlets at Mach numbers 0.8 to 2.65

A mixed compression axisymmetric inlet model with a capture diameter of 50 cm was tested at Mach numbers ranging from 0.8 to 2.65 at 0 deg angle of attack and a constant total pressure of approximately 1 atm. Analytical methods accounting for the effects of both viscous and inviscid flows and incorporating empirical bleed discharge coefficients were used in the procedure for designing the inlet contours and the bleed system. Experimental results are compared with analytic predictions and are also compared with results from earlier tests of an inlet with the same internal contours but with a bleed system developed by cut and try methods in the wind tunnel. With the bleed configuration predicted by the design procedure, maximum total pressure recovery at the engine face at the design Mach number of 2.65 was 93 percent, with a total pressure distortion less than 10 percent. Corresponding bleed mass flow was approximately 7.5 percent, which was about 1.3 percent less than predicted. At lower supersonic Mach numbers, pressure recovery and bleed were generally lower and distortion generally higher.

Smeltzer, D. B.↗
NASA NTRS1973

Advanced supersonic inlet technology.

Recently, relatively new analytical procedures have been successfully used to design bleed systems for mixed-compression inlets designed to operate efficiently up to Mach number 2.65. The procedures used constitute a major advance in inlet technology by offering a promising approach to attain high internal and external performance for mixed-compression inlets that operate over a large supersonic Mach number range. Unfortunately, there is a lack of data describing bleed hole performance characteristics to verify these procedures at high Mach numbers. This paper briefly discusses the analytical procedures for designing advanced inlet systems and suggests facility modifications wherein the procedures can be verified on large-scale inlet models up to approximately Mach number 4.5.

Sorensen, N. E.↗
NASA NTRS1972

Tests of a mixed compression axisymmetric inlet with large transonic mass flow at Mach numbers 0.6 to 2.65

A 38.8-cm (15.28-in.) capture diameter model of a mixed-compression axisymmetric inlet system with a translating cowl was designed and tested. The internal contours, designed for Mach number 2.65, provided a throat area of 59 percent of the capture area when the cowl was retracted for transonic operation. Other model features included a boundary-layer removal system, vortex generators, an engine airflow bypass system, cowl support struts, and rotating rakes at the engine face. All tunnel testing was conducted at a tunnel total pressure of about 1 atm (a unit Reynolds number of about 8.53 million/m at Mach number 2.65) at angles of attack from 0 deg to 4 deg. Results for the following were obtained: total-pressure recovery and distortion at the engine face as a function of bleed mass-flow ratio, the effect of bleed and vortex generator configurations on pressure recovery and distortion, inlet tolerance to unstart due to changes in angle of attack or Mach number, surface pressure distributions, boundary-layer profiles, and transonic additive drag. At Mach number 2.65 and with the best bleed configurations, maximum total pressure recovery at the engine face ranged from 91 to 94.5 percent with bleed mass-flow ratios from 4 to 9 percent, respectively, and total-pressure distortion was less than 10 percent. At off-design supersonic Mach numbers above 1.70, maximum total-pressure recoveries and corresponding bleed mass flows were about the same as at Mach number 2.65, with about 10 to 15 percent distortion. In the transonic Mach number range, total pressure recovery was high (above 96 percent) and distortion was low (less than 15 percent) only when the inlet mass-flow ration was reduced 0.02 to 0.06 from the maximum theoretical value (0.590 at Mach number 1.0).

Smeltzer, D. B.↗
NASA NTRS1972

Performance estimates for a supersonic axisymmetric inlet system.

Results of recent tests of a large-scale axisymmetric mixed-compression inlet system designed for Mach number 2.65 indicate that the performance of the supersonic diffuser and required boundary-layer bleed system can be accurately estimated with relatively new analytic methods. Thus, many wind tunnel testing hours can be saved by avoiding much of the usual ?cut and try' wind tunnel development.

Sorensen, N. E.↗