Engineering topics
Song, Bo
Publications and source records attributed to Song, Bo.
Mechanical Behavior of Additively Manufactured 304L Stainless Steel.
Abstract not provided.
Dynamic Compressive and Tensile Response of an Additively Manufactured 304L Stainless Steel.
Abstract not provided.
Dynamic High-Temperature Tensile Characterization of an Iridium Alloy with Kolsky Tension Bar Techniques
In this study, conventional Kolsky tension bar techniques were modified to characterize an iridium alloy in tension at elevated strain rates and temperatures. The specimen was heated to elevated temperatures with an induction coil heater before dynamic loading; whereas, a cooling system was applied to keep the bars at room temperature during heating. A preload system was developed to generate a small pretension load in the bar system during heating in order to compensate for the effect of thermal expansion generated in the high-temperature tensile specimen. A laser system was applied to directly measure the displacements at both ends of the tensile specimen in order to calculate the strain in the specimen. A pair of high-sensitivity semiconductor strain gages was used to measure the weak transmitted force due to the low flow stress in the thin specimen at elevated temperatures. The dynamic high-temperature tensile stress–strain curves of a DOP-26 iridium alloy were experimentally obtained at two different strain rates (~1000 and 3000 s -1 ) and temperatures (~750 and 1030°C). The effects of strain rate and temperature on the tensile stress–strain response of the iridium alloy were determined. Finally, the iridium alloy exhibited high ductility in stress–strain response that strongly depended on strain-rate and temperature.
Dynamic High-Temperature Tensile Characterization of an Iridium Alloy.
Abstract not provided.
Variability in Mechanical Properties of Laser Engineered Net Shaping Material.
Abstract not provided.
1.9 kV AlGaN/GaN Lateral Schottky Barrier Diodes on Silicon
In this letter, we present AlGaN/GaN lateral Schottky barrier diodes on silicon with recessed anodes and dual field plates. A low specific on-resistance R ON,SP (5.12 mΩ · cm 2 ), a low turn-on voltage (<0.7 V) and a high reverse breakdown voltage BV (>1.9 kV), were simultaneously achieved in devices with a 25 μm anode/cathode separation, resulting in a power figure-of-merit (FOM) BV2/R ON,SP of 727 MW·cm 2 . The record high breakdown voltage of 1.9 kV is attributed to the dual field plate structure.
Dynamic Compressive Response of Wrought and Additive Manufactured 304L Stainless Steels.
Abstract not provided.
High-Temperature Mechanical Properties of a DOP-26 Iridium Alloy under Impact Loading.
Abstract not provided.
Highly Stretchable Miniature Strain Sensor for Large Strain Measurement.
Abstract not provided.
Dual optical marker Raman characterization of strained GaN-channels on AlN using AlN/GaN/AlN quantum wells and {sup 15}N isotopes
This work shows that the combination of ultrathin highly strained GaN quantum wells embedded in an AlN matrix, with controlled isotopic concentrations of Nitrogen enables a dual marker method for Raman spectroscopy. By combining these techniques, we demonstrate the effectiveness in studying strain in the vertical direction. This technique will enable the precise probing of properties of buried active layers in heterostructures, and can be extended in the future to vertical devices such as those used for optical emitters and for power electronics.
Dynamic high-temperature Kolsky tension bar techniques
Kolsky tension bar techniques were modified for dynamic high-temperature tensile characterization of thin-sheet alloys. An induction coil heater was used to heat the specimen while a cooling system was applied to keep the bars at room temperature during heating. A preload system was developed to generate a small pretension load in the bar system during heating in order to compensate for the effect of thermal expansion generated in the high-temperature tensile specimen. A laser system was applied to directly measure the displacements at both ends of the tensile specimen in order to calculate the strain in the specimen. A pair of high-sensitivity semiconductor strain gages was used to measure the weak transmitted force due to the low flow stress in the thin specimen at elevated temperatures. As an example, the high-temperature Kolsky tension bar was used to characterize a DOP-26 iridium alloy in high-strain-rate tension at 860 s(-1)/1030 degrees C.
Origin of ferromagnetism in aluminum-doped TiO2 thin films: Theory and experiments
Not Available
A Novel Splitting-beam Laser Extensometer Technique for Kolsky Tension Bar Experiments.
Abstract not provided.
Mechanical Response of Additively Manufactured 304L Across a Wide Spectrum of Loading Conditions.
Abstract not provided.