Engineering Papers⌕ Search

Engineering topics

Song, Bo

Publications and source records attributed to Song, Bo.

At least 109 records · Page 6

Development of a New Method to Investigate Dynamic Friction Behavior of Metallic Materials Using a Kolsky Tension Bar

Understanding the interfacial behavior of two materials sliding relative to each other is import ant in computational modeling and simulating impact or shock response of components, subsystems, and even full-scale systems. Although often considered as a constant for different applications, the coefficient of friction may be dependent on a number of factors such as normal force, roughness, material type, temperature, and sliding velocity. In this study, a new method based on a Kolsky tension bar with a custom-made friction fixture was developed for measurement of the dynamic friction coefficient between two metallic materials at high sliding velocities. In this new method, polyvinylidene fluoride (PVDF) thin film force sensors were used to measure the normal force, while a strain gage on the transmission bar was used to measure the friction force. As such, the dynamic friction coefficient is calculated with the normal and friction forces. The impact velocity can be varied to investigate the dependency of friction coefficient on impact velocity. To evaluate the technique, friction coefficients between 4340 steel and 7075-T6 we re measured at three different sliding velocities of 4, 8 and 11 m/s. Effects of surface roughness, normal force, and impact speed were also explored . Decreased static and kinetic friction coefficient s were observed when the normal force was increased at constant sliding velocity. With increasing velocity, the friction coefficient remained fairly constant for the three velocities studied. Higher friction coefficients were measured when the specimen roughness was increased.

36 MATERIALS SCIENCE↗

Synergistic Phase and Disorder Engineering in 1T‐MoSe 2 Nanosheets for Enhanced Hydrogen‐Evolution Reaction

MoSe 2 is a promising earth‐abundant electrocatalyst for the hydrogen‐evolution reaction (HER), even though it has received much less attention among the layered dichalcogenide (MX 2 ) materials than MoS 2 so far. Here, a novel hydrothermal‐synthesis strategy is presented to achieve simultaneous and synergistic modulation of crystal phase and disorder in partially crystallized 1T‐MoSe 2 nanosheets to dramatically enhance their HER catalytic activity. Careful structural characterization and defect characterization using positron annihilation lifetime spectroscopy correlated with electrochemical measurements show that the formation of the 1T phase under a large excess of the NaBH 4 reductant during synthesis can effectively improve the intrinsic activity and conductivity, and the disordered structure from a lower reaction temperature can provide abundant unsaturated defects as active sites. Such synergistic effects lead to superior HER catalytic activity with an overpotential of 152 mV versus reversible hydrogen electrode (RHE) for the electrocatalytic current density of j = −10 mA cm −2 , and a Tafel slope of 52 mV dec −1 . This work paves a new pathway for improving the catalytic activity of MoSe 2 and generally MX 2 ‐based electrocatalysts via a synergistic modulation strategy.

Yin, Ying↗

Electron mobility in polarization-doped Al0-0.2GaN with a low concentration near 1017 cm−3

In this letter, carrier transport in graded AlxGa1-xN with a polarization-induced n-type doping as low as ∼1017 cm−3 is reported. The graded AlxGa1-xN is grown by metal organic chemical vapor deposition on a sapphire substrate, and a uniform n-type doping without any intentional doping is realized by linearly varying the Al composition from 0% to 20% over a thickness of 600 nm. A compensating center concentration of ∼1017 cm−3 was also estimated. A peak mobility of 900 cm2/V·s at room temperature is extracted at an Al composition of ∼7%, which represents the highest mobility achieved in n-Al0.07GaN with a carrier concentration of ∼1017 cm−3. A comparison between experimental data and theoretical models shows that, at this low doping concentration, both dislocation scattering and alloy scattering are significant in limiting electron mobility and that a dislocation density of <107 cm−2 is necessary to optimize mobility near 1016 cm−3. The findings in this study provide insights into key elements for achieving high mobility at low doping levels in GaN, a critical parameter in the design of novel power electronics taking advantage of polarization doping.

Zhu, Mingda↗

Particle size effect in porous film electrodes of ligand-modified graphene for enhanced supercapacitor performance

Graphene-based electrodes for high performance supercapacitors are developed by taking advantage of particle size control, large mass loading, and surface functionalization of reduced graphene oxide (rGO) sheets. Two controlled sizes of graphene sheets (100 nm vs. 45 μm average lateral dimensions) were prepared to study two-electrode system performance. The nano-size graphenes led to the formation of mesoporous films, resulting in higher capacitance, better capacitance retension and lower equivalent series resistance (ESR), indicating better surface usability for diffusion and accessibility of electrolyte ions by shortening transport paths (compared with horizontally stacked films from micro-sized graphenes). For studies using an aqueous electrolyte, the maximum specific capacitance of nano-rGO film was 302 F/g (at 1 A/g with 4.3 mg/cm 2 of mass loading), which was ~2.4 times higher than micro-rGO film, and achieved a ~67% reduced ESR. With an organic electrolyte, the nano-rGO delivered ~4.2 times higher capacitance (115 F/g at 2 A/g with 4.3 mg/cm 2 ), 4.0 times lower IR drops, and an order-of-magnitude lower charge-transfer resistance with an energy density of 18.7 Wh/kg. Finally, the results of this work indicate that the size control of graphene sheet particles for film deposit electrodes can be a simple but effective approach to improve supercapacitor performance.

36 MATERIALS SCIENCE↗

Experimental evaluation of low-pass shock isolation performance of elastomers using frequency-based Kolsky bar analyses

Elastomeric materials are used as shock isolation materials in a variety of environments to dampen vibrations and/or absorb energy from external impact to minimize energy transfer between two objects or bodies. Some applications require the shock isolation materials to behave as a low-pass mechanical filter to mitigate the shock/impact at high frequencies but transmit the energy at low frequencies with minimal attenuation. To fulfill this requirement, a shock isolation material needs to be carefully evaluated and selected with proper experimental design, procedures, and analyses. In this study, a Kolsky bar was modified with precompression (up to 15.5 kN) and confinement capabilities to evaluate low-pass shock isolation performance in terms of acceleration attenuation through a variety of elastomers. Also investigated were the effects of preload and specimen geometry on the low-pass shock isolation response.

36 MATERIALS SCIENCE↗

Wave transmission through silicone foam pads in a compression Kolsky bar apparatus. Comparisons between simulations and measurements.

This memo concerns the transmission of mechanical signals through silicone foam pads in a compression Kolsky bar set-up. The results of numerical simulations for four levels of pad pre-compression and two striker velocities were compared directly to test measurements to assess the delity of the simulations. The nite element model simulated the Kolsky tests in their entirety and used the hyperelastic `hyperfoam' model for the silicone foam pads. Calibration of the hyperfoam model was deduced from quasi-static compression data. It was necessary, however, to augment the material model by adding sti ness proportional damping in order to generate results that resembled the experimental measurements. Based on the results presented here, it is important to account for the dynamic behavior of polymeric foams in numerical simulations that involve high loading rates.

47 OTHER INSTRUMENTATION↗

Microscopic vertical orientation of nano-interspaced graphene architectures in deposit films as electrodes for enhanced supercapacitor performance

This paper reported a novel two-step process to fabricate high-performance supercapacitor films that contain microscale domains of nano-interspaced, re-stacked graphene sheets oriented perpendicular to the surface of current collector substrate, i.e., carbon fiber paper. In the two-step process, we first used ligand molecules to modify the surface of graphene oxide (GO) sheets and manipulate the interspacing between the re-stacked GO sheets. The ligand-modified GOs, i.e., m-GOs, were then reduced to obtain more conductive graphene (m-rGO), where X-ray diffraction measurement results indicated well-controlled interlayer spacing between the restacked m-rGO sheets up to 1 nm. The typical lateral dimension of the restacked m-rGO sheets were ~40 µm. Then, electrical field was introduced during m-rGO slurry deposition process to induce the vertical orientation of the m-rGO sheets/stacks in the film deposit. The direct current electrical field induced the orientation of the domains of m-rGO stacks along the direction perpendicular to the surface of deposit film, i.e., direction of electric field. Also, the applied electric field increased the interlayer spacing further, which should enhance the diffusion and accessibility of electrolyte ions. As compared with the traditionally deposited “control” films, the field-processed film deposits that contain oriented structure of graphene sheets/stacks have shown up to ~1.6 times higher values in capacitance (430 F/g at 0.5 A/g) and ~67% reduction in equivalent series resistance. Finally, the approach of using electric field to tailor the microscopic architecture of graphene-based deposit films is effective to fabricate film electrodes for high performance supercapacitors.

36 MATERIALS SCIENCE↗