Engineering Papers⌕ Search

Engineering topics

Solodov, A. A.

Publications and source records attributed to Solodov, A. A..

At least 19 records

Mitigation of hot-electron preheat from the two-plasmon-decay instability using silicon-doped plastic shells in direct-drive implosions on OMEGA

Hot electrons generated by the two-plasmon-decay (TPD) instability in laser-direct-drive implosions preheat the fuel and degrade performance. The mitigation of preheat using silicon-doped ablators (i.e., preheat is reduced by a factor of 1.40 ± 0.04) while decreasing the ratio of the laser spot diameter to the target diameter (⁠R b /R t⁠ ) to mitigate cross-beam energy transfer has been demonstrated on the OMEGA laser for quarter-critical laser intensities of 4.1 x 10 14 W/cm 2 ⁠, equivalent to an incident laser intensity of 8.3 x 10 14 W/cm 2 ⁠. The silicon dopant increases the electron temperature of the ablation plasma, which raises the intensity threshold for the onset of the TPD instability. These results show that implosion designs utilizing higher drive intensities can be used to achieve higher shell velocities, which are currently inaccessible with plastic ablators due to excessive preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pump depletion and the Raman gap in ignition-scale plasmas

Laser-plasma instabilities under ignition conditions for direct-drive inertial confinement fusion are studied using two-dimensional Particle-in-Cell simulations with a combination of in-plane (PP) and out-of-the-plane (SP) lasers. The results show that stimulated Raman side scattering can induce significant pump depletion and form a gap in the Raman scattered light spectra that have been observed in experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of a hydrodynamically equivalent burning plasma in direct-drive inertial confinement fusion

Focussing laser light onto the surface of a small target filled with deuterium and tritium implodes it and leads to the creation of a hot and dense plasma, in which thermonuclear fusion reactions occur. In order for the plasma to become self-sustaining, the heating of the plasma must be dominated by the energy provided by the fusion reactions—a condition known as a burning plasma. A metric for this is the generalized Lawson parameter, where values above around 0.8 imply a burning plasma. Here, we report on hydro-equivalent scaling of experimental results on the OMEGA laser system and show that these have achieved core conditions that reach a burning plasma when the central part of the plasma, the hotspot, is scaled in size by at least a factor of 3.9 ± 0.10, which would require a driver laser energy of at least 1.7 ± 0.13 MJ. In addition, we hydro-equivalently scale the results to the 2.15 MJ of laser energy available at the National Ignition Facility and find that these implosions reach 86% of the Lawson parameter required for ignition. Furthermore, our results support direct-drive inertial confinement fusion as a credible approach for achieving thermonuclear ignition and net energy in laser fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of overlapping laser beams and density scale length in laser-plasma instability experiments on OMEGA EP

Experiments have been conducted on the OMEGA EP laser facility to study the effect of density scale length and overlapping beam geometry on laser-plasma instabilities near and below the quarter-critical density. Experiments were conducted in both planar geometry (density scale length L n ~ 190 to 300 μm) and spherical geometry (L n ~ 150 μm) with up to four overlapping beams and were designed to have overlapped intensities and density scale lengths comparable to OMEGA spherical experiments, but with many fewer beams. In comparison with previous experiments on OMEGA and National Ignition Facility, it is confirmed that shorter density scale lengths favor the two-plasmon decay (TPD) instability, while longer density scale lengths favor stimulated Raman scattering (SRS). In addition, for experiments at the same scale length and overlapped laser intensity, higher single-beam intensities favor SRS, while a larger number of overlapping beams favor TPD.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hot-electron preheat and mitigation in polar-direct-drive experiments at the National Ignition Facility

Target preheat by superthermal electrons from laser–plasma instabilities is a major obstacle to achieving thermonuclear ignition via direct-drive inertial confinement fusion at the National Ignition Facility (NIF). Polar-direct-drive surrogate plastic implosion experiments were performed on the NIF to quantify preheat levels at ignition-relevant scale and develop mitigation strategies. Here, the experiments were used to infer the hot-electron temperature, energy fraction, divergence, and to directly measure the spatial hot-electron energy deposition profile inside the imploding shell. Silicon layers buried in the ablator are shown to mitigate the growth of laser–plasma instabilities and reduce preheat, providing a promising path forward for ignition designs at an on-target intensity of about 10 15 W/cm 2 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Role of hot electrons in shock ignition constrained by experiment at the National Ignition Facility

Shock ignition is a scheme for direct drive inertial confinement fusion that offers the potential for high gain with the current generation of laser facility; however, the benefits are thought to be dependent on the use of low adiabat implosions without laser–plasma instabilities reducing drive and generating hot electrons. A National Ignition Facility direct drive solid target experiment was used to calibrate a 3D Monte Carlo hot-electron model for 2D radiation-hydrodynamic simulations of a shock ignition implosion. The α = 2.5 adiabat implosion was calculated to suffer a 35% peak areal density decrease when the hot electron population with temperature T ℎ = 55 keV and energy E ℎ = 13 kJ was added to the simulation. Optimizing the pulse shape can recover ~1/3 of the peak areal density lost due to a change in shock timing. Here, despite the harmful impact of laser–plasma instabilities, the simulations indicate shock ignition as a viable method to improve performance and broaden the design space of near ignition high adiabat implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct Measurements of DT Fuel Preheat from Hot Electrons in Direct-Drive Inertial Confinement Fusion

Hot electrons generated by laser-plasma instabilities degrade the performance of laser-fusion implosions by preheating the DT fuel and reducing core compression. The hot-electron energy deposition in the DT fuel has been directly measured for the first time by comparing the hard x-ray signals between DT-layered and mass-equivalent ablator-only implosions. The electron energy deposition profile in the fuel is inferred through dedicated experiments using Cu-doped payloads of varying thickness. The measured preheat energy accurately explains the areal-density degradation observed in many OMEGA implosions. This technique can be used to assess the viability of the direct-drive approach to laser fusion with respect to the scaling of hot-electron preheat with laser energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct Measurements of DT Fuel Preheat from Hot Electrons in Direct-Drive Inertial Confinement Fusion

Hot electrons generated by laser-plasma instabilities degrade the performance of laser-fusion implosions by preheating the DT fuel and reducing core compression. The hot-electron energy deposition in the DT fuel has been directly measured for the first time by comparing the hard x-ray signals between DT-layered and mass-equivalent ablator-only implosions. The electron energy deposition profile in the fuel is inferred through dedicated experiments using Cu-doped payloads of varying thickness. The measured preheat energy accurately explains the areal-density degradation observed in many OMEGA implosions. Furthermore, this technique can be used to assess the viability of the direct-drive approach to laser fusion with respect to the scaling of hot-electron preheat with laser energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct-drive laser fusion: status, plans and future

Laser-direct drive (LDD), along with laser indirect (X-ray) drive (LID) and magnetic drive with pulsed power, is one of the three viable inertial confinement fusion approaches to achieving fusion ignition and gain in the laboratory. The LDD programme is primarily being executed at both the Omega Laser Facility at the Laboratory for Laser Energetics and at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. LDD research at Omega includes cryogenic implosions, fundamental physics including material properties, hydrodynamics and laser–plasma interaction physics. LDD research on the NIF is focused on energy coupling and laser–plasma interactions physics at ignition-scale plasmas. Limited implosions on the NIF in the ‘polar-drive’ configuration, where the irradiation geometry is configured for LID, are also a feature of LDD research. The ability to conduct research over a large range of energy, power and scale size using both Omega and the NIF is a major positive aspect of LDD research that reduces the risk in scaling from OMEGA to megajoule-class lasers. Furthermore, the paper will summarize the present status of LDD research and plans for the future with the goal of ultimately achieving a burning plasma in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hot-electron generation at direct-drive ignition-relevant plasma conditions at the National Ignition Facility

Laser–plasma interaction instabilities can be detrimental for direct-drive inertial confinement fusion by generating high-energy electrons that preheat the target. Moreover, an experimental platform has been developed and fielded on the National Ignition Facility to investigate hot-electron production from laser–plasma instabilities at direct-drive ignition-relevant conditions. The radiation-hydrodynamic code DRACO has been used to design planar-target experiments that generate plasma and interaction conditions comparable to direct-drive ignition designs: I L ~10 15 W/cm 2 , T e > 3 keV, and density-gradient scale lengths of L n ~ 600 μ m in the quarter-critical density region. The hot-electron properties were inferred by comparing the experimentally observed hard x-ray spectra to Monte Carlo simulations of hard x-ray emission from hot electrons depositing energy in the target. Hot-electron temperatures of ~40 keV to 60 keV and the fraction of laser energy converted to hot electrons of ~0.5% to 5% were inferred in plastic targets for laser intensities at the quarter-critical density surface of (~4 to 14) × 10 14 W/cm 2 . The use of silicon ablators was found to mitigate the hot-electron preheat by increasing the threshold laser intensity for hot-electron generation from ~3.5 × 10 14 W/cm 2 in plastic to ~6 × 10 14 W/cm 2 in silicon. The overall hot-electron production is further reduced in silicon ablators when the intensity threshold is exceeded.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stimulated Raman scattering mechanisms and scaling behavior in planar direct-drive experiments at the National Ignition Facility

Stimulated Raman scattering (SRS) has been investigated comprehensively in planar-geometry experiments at the National Ignition Facility at conditions relevant to the corona of inertial con finement fusion (ICF) ignition-scale direct-drive targets. These experiments at measured electron temperatures of 4 to 5 keV, simulated density scale lengths Ln of 400 to 700 um, and laser intensities at the quarter-critical density of up to 1.5 x 10 15 W/cm 2 have determined SRS thresholds and the scaling behavior of SRS for various beam geometries. Several SRS mechanisms, including saturated absolute SRS near the quarter-critical density and additional SRS, including near-backscatter or sidescatter at lower densities, have been identi fied. Correlation of time-dependent SRS at densities ~0.15 to 0.21 of the critical density with hot-electron signatures, as well as the magnitudes of these signatures across different experiments, is observed. Additional modeling work is needed to de nitively identify the density region in which hot electrons are generated, and will guide SRS and hot-electron preheat mitigation strategies for direct-drive-ignition designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Parameterizing hot electron energy distributions for tabular emissivities and opacities

Cold Kα and Kβ emission spectroscopy is a powerful diagnostic for plasma conditions and distributions of energetic electrons produced in short pulse laser experiments. SPECT3D post-processes hydrodynamics code output and simulates high-resolution spectra and images for plasmas containing arbitrary distributions of hot electrons, however these calculations can become prohibitively expensive for plasmas requiring complex atomic data and detailed computational grids. To significantly increase calculation speed, it is desirable to use pre-configured opacity tables that include information about hot electrons, rather than calculating emissivity and opacity for every grid point by solving collisional-radiative atomic kinetic rate equations. However, to tabulate such opacities, a general parameter-based description of hot electron energy distributions must be found. To be practical, hot electrons should be represented with an analytic function of just a few parameters which, in addition to temperature and density, can be used to define parameter space for opacity tables. In this paper, we present a method that allows for describing a set of arbitrary binned hot electron distributions with a simple analytic function, with only a modest impact on the accuracy of the simulations. Increased calculation speeds of 50–100x are demonstrated. In conclusion, we also discuss details of opacity calculations and present synthetic spectroscopy data based on post-processing of detailed particle-in-cell simulations relevant to the ongoing experimental campaign at the Omega EP laser facility.

74 ATOMIC AND MOLECULAR PHYSICS↗

Refining instrument response functions with 3-D Monte Carlo simulations of differential hard x-ray spectrometers

Three x-ray spectrometers – the hard x-ray detector (HXRD), the bremsstrahlung MeV x-ray spectrometer (BMXS), and the hard x-ray image plate (HXIP) – areused here to estimate hot-electron bremsstrahlung spectrum parameters for inertial confinement fusion experiments on OMEGA. Using 1-D deterministically calculated response functions, they show significantly different estimates of spectrum slope temperature. For all three detectors, 3-D Geant4 Monte Carlo simulations are developed and used to compute instrument response functions. Simulations explain features in raw image-plate data, but only significantly improve systematic errors in predicted detector channel signals for BMXS and do not entirely eliminate the discrepancy between estimates of slope temperature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Theory and measurements of convective Raman side scatter in inertial confinement fusion experiments

Raman side-scatter, whereby scattered light is resonant while propagating perpendicular to a density gradient in a plasma, was identi ed experimentally in planar-target experiments at the National Ignition Facility (NIF) at intensities orders of magnitudes below the threshold for absolute instability. We have derived a new theoretical description of convective Raman side-scatter below the absolute threshold, validated by numerical simulations. We show that ICF experiments at full ignition-scale, i.e. with mm-scale spot sizes and density scale lengths, are prone to increased coupling losses from Raman side-scatter as the instability can extend from the absolute regime near the quarter-critical density to the convective regime at lower electron densities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tripled yield in direct-drive laser fusion through statistical modelling

Accurate predictive models are essential to the design of high-performance, laser-fusion experiments. Here, we report the development of a promising statistical approach that has been used to quantitatively predict and design several cryogenic deuterium-tritium (DT) implosions on the OMEGA Laser System, leading to the tripling of the fusion yield to its highest value for direct-drive laser fusion of DT-layered targets. When scaled to National Ignition Facility laser energies of 1.9 MJ, these targets are predicted to produce a fusion energy output of ~500 kJ—several times larger than current fusion yields achieved at that facility. Future applications of this approach will guide the exploration of the vast parameter space for the conditions required for thermonuclear ignition and expose gaps in our understanding of laser-fusion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tripled yield in direct-drive laser fusion through statistical modelling [Tripling the yield in direct-drive laser fusion via predictive statistical modeling]

Focusing laser light onto a very small target can produce the conditions for laboratory-scale nuclear fusion of hydrogen isotopes. The lack of accurate predictive models, which are essential for the design of high-performance laser-fusion experiments, is a major obstacle to achieving thermonuclear ignition. Here we report a statistical approach that was used to design and quantitatively predict the results of implosions of solid deuterium–tritium targets carried out with the 30-kilojoule OMEGA laser system, leading to tripling of the fusion yield to its highest value so far for direct-drive laser fusion. When scaled to the laser energies of the National Ignition Facility (1.9 megajoules), these targets are predicted to produce a fusion energy output of about 500 kilojoules—several times larger than the fusion yields currently achieved at that facility. As a result, this approach could guide the exploration of the vast parameter space of thermonuclear ignition conditions and enhance our understanding of laser-fusion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

X-ray spectroscopy of planar laser-plasma interaction experiments at the National Ignition Facility

X-ray spectroscopy has been newly used to diagnose electron temperatures in planar-geometry experiments at the National Ignition Facility (NIF) designed to study laser-plasma interactions at plasma conditions relevant to direct-drive ignition. These experiments used a buried co-mixed Mn/Co microstrip in a CH ablator in experiments that generated long scale-length plasmas susceptible to stimulated Raman scattering (SRS). Time-resolved Mn and Co K-shell spectra, diagnosed using the NIF x-ray spectrometer, were analyzed by fi tting to synthetic spectra based on a detailed atomic model of emission from the microstrip. The electron temperature at the time when the microstrip passes through the quarter-critical density surface, the key region for the development of SRS, was inferred to be around 2 to 3 keV. These measurements constrain 2-D DRACO radiation-hydrodynamics modeling of the planar experiments, important for determining plasma conditions pertinent to SRS, and demonstrate that this platform approaches direct-drive ignition-relevant conditions. The modeling is also assessed by a direct comparison of measured spectra to modeled spectra generated by DRACO in conjunction with the atomic physics postprocessor code SPECT3D.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The National Direct-Drive Inertial Confinement Fusion Program

The National Direct-Drive Inertial Confinement Fusion Program consists of the 100-Gbar Campaign on the 30-kJ, 351-nm, 60-beam OMEGA Laser System and the Megajoule Direct-Drive (MJDD) Campaign on the 1.8-MJ, 351-nm, 192-beam National Ignition Facility (NIF). The main goals of the 100-Gbar Campaign are to demonstrate and understand the physics for hot-spot conditions and formation relevant for ignition at the MJ scale, while the MJDD Campaign seeks to understand the laser-plasma interactions, energy coupling, and laser imprint for ignition-scale direct-drive coronal plasmas. An overview of the multi-year, systematic effort that is underway for the National Direct-Drive Inertial Confinement Fusion Program (including laser, target, and diagnostic improvements in progress), as well as recent results from the 100-Gbar Campaign on OMEGA and the MJDD Campaign on NIF is presented in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗