Engineering topics

Smith, S. C.

Publications and source records attributed to Smith, S. C..

7 records

NASA NTRS1995

Pressure-sensitive paint measurements on a supersonic high-sweep oblique wing model

The pressure-sensitive paint method was used in the test of a high-sweep oblique wing model, conducted in the NASA Ames 9- by 7-ft Supersonic Wind Tunnel. Surface pressure data was acquired from both the luminescent paint and conventional pressure taps at Mach numbers between M = 1.6 and 2.0. In addition, schlieren photographs of the outer flow were used to determine the location of shock waves impinging on the model. The results show that the luminescent pressure-sensitive paint can capture both global and fine features of the static surface pressure field. Comparison with conventional pressure tap data shows good agreement between the two techniques, and that the luminescent paint data can be used to make quantitative measurements of the pressure changes over the model surface. The experiment also demonstrates the practical considerations and limitations that arise in the application of this technique under supersonic flow conditions in large-scale facilities, as well as the directions in which future research is necessary in order to make this technique a more practical wind-tunnel testing tool.

McLachlan, B. G.↗

NASA NTRS1993

Statistical modeling of capture, association, and exit-channel dynamics in the CH3(+)/CH3CN system

The ion-molecule CH3(+) + CH3CN reaction is presently modeled by means of a master equation treatment incorporating weak collisions. The parameter required for the Rice-Ramsberger-Kassel-Markus (RRKM) treatment is derived from an ab initio investigation of the energy surface in question, and a means of including the capture rate coefficients in the RRKM approach is developed in which only the hindered dipole rotation is coupled in the reaction coordinate at large separations. Unimolecular rate coefficients for the (CH3CNCH3+)-activated complex are calculated for all product channels in the 300-600 K temperature range.

Smith, S. C.↗

NASA NTRS1987

The design of a joined wing flight demonstrator aircraft

A joined-wing flight demonstrator aircraft has been developed at the NASA Ames Research Center in collaboration with ACA Industries. The aircraft is designed to utilize the fuselage, engines, and undercarriage of the existing NASA AD-1 flight demonstrator aircraft. The design objectives, methods, constraints, and the resulting aircraft design, called the JW-1, are presented. A wind-tunnel model of the JW-1 was tested in the NASA Ames 12-foot wind tunnel. The test results indicate that the JW-1 has satisfactory flying qualities for a flight demonstrator aircraft. Good agreement of test results with design predictions confirmed the validity of the design methods used for application to joined-wing configurations.

Smith, S. C.↗

NASA NTRS1985

Airflow calibration of a bellmouth inlet for measurement of compressor airflow in turbine-powered propulsion simulators

The development of turbine-powered propulsion simulators for high-speed wind tunnel models requires a bellmouth inlet which can accurately measure compressor-inlet airflow. A bellmouth inlet was instrumented with total pressure probes, static pressure probes, and thermocouples for airflow measurement. The bellmouth flowmeter against a critical venturi flowmeter was calibrated. The calibration was done at four inlet pressures ranging from 58 to 114 kPa. The bellmouth discharge coefficient varied as a function of bellmouth-throat Mach number. Over the range of Reynolds number and Mach number tested the Reynolds number was not a significant influence on the discharge coefficient. The overall accuracy of the bellmouth inlet as a flowmeter was estimated to be + or - 0.5% of the flowmeter reading.

Smith, S. C.↗

NASA NTRS1983

Determining compressor-inlet airflow in the compact multimission aircraft propulsion simulators in wind-tunnel applications

Test techniques are being developed to use the Compact Multimission Aircraft Propulsion Simulator (CMAPS) in wind-tunnel tests. The CMAPS allows simultaneous simulation of inlet and exhaust flow fields. Static tests have been conducted to acquire CMAPS performance data and to evaluate four methods of determining compressor inlet airflow during wind-tunnel tests. The first method measures airflow at the compressor face; the second measures airflow in the compressor discharge duct; the third deduces the compressor airflow from the calibrated nozzle, turbine supply, and turbine bleed airflows; and the fourth correlates compressor airflow with the mixer pressure. Test results and the advantages, disadvantages, and expected accuracy of each method are discussed.

Smith, S. C.↗

NASA NTRS1983

Propulsion simulation test technique for V/STOL configurations

Ames Research Center is developing the technology for turbine-powered jet engine simulators so that airframe/propulsion system interactions on V/STOL fighter aircraft and other highly integrated configurations can be studied. This paper describes the status of the compact multimission aircraft propulsion simulator (CMAPS) technology. Three CMAPS units have accumulated a total of 340 hr during approximately 1-1/2 yr of static and wind-tunnel testing. A wind-tunnel test of a twin-engine CMAPS-equipped close-coupled canard-wing V/STOL model configuration with nonaxisymmetric nozzles was recently completed. During this test approximately 140 total hours were logged on two CMAPS units, indicating that the rotating machinery is reliable and that the CMAPS and associated control system provide a usable test tool. However, additional development is required to correct a drive manifold O-ring problem that limits the engine-pressure-ratio (EPR) to approximately 3.5.

Bailey, R. O.↗

NASA NTRS1981

Lift-enhancing surfaces on several advanced V/STOL fighter/attack aircraft concepts

An analysis of the relative influences of forward lift-enhancing surfaces on the overall lift and drag characteristics of three wind-tunnel models representative of V/STOL fighter/attack aircraft is presented. Two of the models are canard-wing configurations and one has a wing leading-edge extension (LEX) as the forward lifting surface. Data are taken from wind-tunnel tests of each model covering Mach numbers from 0.4 to 1.4. Overall lift and drag characteristics of these models and the generally favorable interactions of the forward surfaces with the wings are highlighted. Results indicate that larger LEX's and canards generally give greater lift and drag improvements than ones that are smaller relative to the wings.

Durston, D. A.↗