Engineering Papers⌕ Search

Engineering topics

Smith, Mark T

Publications and source records attributed to Smith, Mark T.

Electrohydraulic Forming of Near-Net Shape Automotive Panels - Final CRADA Report

This report provides the results of a Cooperative Research and Development Agreement (CRADA) project between Pacific Northwest National Laboratory and the Ford Motor Company intended to demonstrate the relevance of using the electrohydraulic forming (EHF) process as a near-net-shape automotive panel manufacturing technology to simultaneously reduce the energy embedded in vehicles and the energy consumed while producing automotive structures. The application of EHF by automotive manufacturers and their suppliers could significantly reduce the amount of tooling, manufacturing equipment, and material input compared to conventional stamping technologies, while at the same time producing superior, near-net-shape stampings and parts. EHF represents a highly viable manufacturing technology because of its ability to form all types of sheet materials. Furthermore, the EHF process has been used to produce prototype components for commercialization evaluations at Ford. Given the results of this project, including the tensile tests and modeling presented in this report and further work performed internally at Ford, Ford Motor Company will remain active in the development and commercialization of the EHF manufacturing method.

Soulami, Ayoub↗

Electro-Hydraulic Forming of Sheet Metals: Free-forming vs. Conical-die Forming

This work builds upon our recent advances in quantifying high-rate deformation behavior of sheet metals, during electro-hydraulic forming (EHF), using high-speed imaging and digital image correlation techniques. Following recent publication of an earlier manuscript, resulting from this project, in the Journal of Materials Processing Technology, this manuscript further details our results and compares forming behavior when the process is carried out inside an open-die or a conical die. It is anticipated that quantitative information of the sheet deformation history, made possible by the experimental technique developed in this work, will improve our understanding on the roles of strain-rate and sheet-die interactions in enhancing the sheet metal formability during high-rate forming. This knowledge will be beneficial to the automotive industry and enable them to fabricate light-weight sheet parts out of Al and advanced high strength steels.

36 MATERIALS SCIENCE↗

Experimental Characterization of Sheet Metal Deformation During Electro-Hydraulic Forming

This manuscripts reports results of the last 2-3 years work pertaining to DOE-OVT funded project on pulse-pressure forming of light-weight materials. We report experimental results of electrohydraulically formed sheets where data is determined using a pair of high-speed cameras and analyzed using a digital image correlation technique. These results are relevant to the formability of sheet materials and of importance to the automotive industry. To the authors’ knowledge, such results have not been published in the literature.

36 MATERIALS SCIENCE↗

Forming Limits of Weld Metal in Aluminum Alloys and Advanced High-Strength Steels

This work characterizes the mechanical properties of DP600 laser welded TWBs (1 mm-1.5 mm) near and in the weld, as well as their limits of formability. The approach uses simple uniaxial experiments to measure the variability in the forming limits of the weld region, and uses a theoretical forming limit diagram calculation to establish a probabilistic distribution of weld region imperfection using an M-K method approach

36 MATERIALS SCIENCE↗

Formability of Al 5xxx Sheet Metals Using Pulsed Current for Various Heat Treatments

Previous studies have shown that the presence of a pulsed electrical current, applied during the deformation process of an aluminum specimen, can significantly improve the formability of the aluminum without heating the metal above its maximum operating temperature range. The research herein extends these findings by examining the effect of electrical pulsing on 5052 and 5083 Aluminum Alloys. Two different parameter sets were used while pulsing three different heat treatments (As Is, 398°C, and 510°C) for each of the two aluminum alloys. For this research, the electrical pulsing is applied to the aluminum while the specimens are deformed, without halting the deformation process (a manufacturing technique known as Electrically-Assisted Manufacturing). The analysis focuses on establishing the effect the electrical pulsing has on the aluminum alloy’s various heat treatments by examining the displacement of the material throughout the testing region of dogbone-shaped specimens. The results from this research show that pulsing significantly increases the maximum achievable elongation of the aluminum (when compared to baseline tests conducted without electrical pulsing). Another beneficial effect produced by electrical pulsing is that the engineering flow stress within the material is considerably reduced. The electrical pulses also cause the aluminum to deform non-uniformly, such that the material exhibits a diffuse neck where the minimum deformation occurs near the ends of the specimen (near the clamps) and the maximum deformation occurs near the center of the specimen (where fracture ultimately occurs). This diffuse necking effect is similar to what can be experienced during superplastic deformation. However, when comparing the presence of a diffuse neck in this research, electrical pulsing does not create as significant of a diffuse neck as superplastic deformation. Electrical pulsing has the potential to be more efficient than traditional methods of incremental forming since the deformation process is never interrupted. Overall, with the greater elongation and lower stress, the aluminum can be deformed quicker, easier, and to a greater extent than is currently possible.

36 MATERIALS SCIENCE↗

High-Strain-Rate Forming of Aluminum and Steel Sheets for Automotive Applications

The formability of aluminum alloy AA5182-O and DP600 steel sheets at high-strain-rates was investigated using an electrohydraulic forming (EHF) setup. Test sheets, ~150 mm diameter x 1 mm thick, were clamped around their circumference and subjected to a pressure-pulse (several 100's duration) generated by a high-energy (up to ~34 kJ) under-water electrical discharge. The real-time strain and strain-rate of the deforming sheets were quantified by the digital image correlation (DIC) technique using a pair of high-speed cameras (~15's per frame). Strain-rate amplification was observed when the sheets were deformed into a conical die, with the maximum in-plane strain-rate and strain for aluminum measured as ~1200 /s and ~0.2, respectively. The deformation behavior of the sheets was modeled using ABAQUS/finite element explicit code and better correlation, between the predicted and the experimental sheet deformation behavior, was observed when an alternate pressure-profile was used instead of the one available from the literature.

36 MATERIALS SCIENCE↗

Implementation of New Process Models for Tailored Polymer Composite Structures into Processing Software Packages

This report describes the work conducted under the Cooperative Research and Development Agreement (CRADA) (Nr. 260) between the Pacific Northwest National Laboratory (PNNL) and Autodesk, Inc. to develop and implement process models for injection-molded long-fiber thermoplastics (LFTs) in processing software packages. The structure of this report is organized as follows. After the Introduction Section (Section 1), Section 2 summarizes the current fiber orientation models developed for injection-molded short-fiber thermoplastics (SFTs). Section 3 provides an assessment of these models to determine their capabilities and limitations, and the developments needed for injection-molded LFTs. Section 4 then focuses on the development of a new fiber orientation model for LFTs. This model is termed the anisotropic rotary diffusion - reduced strain closure (ARD-RSC) model as it explores the concept of anisotropic rotary diffusion to capture the fiber-fiber interaction in long-fiber suspensions and uses the reduced strain closure method of Wang et al. to slow down the orientation kinetics in concentrated suspensions. In contrast to fiber orientation modeling, before this project, no standard model was developed to predict the fiber length distribution in molded fiber composites. Section 5 is therefore devoted to the development of a fiber length attrition model in the mold. Sections 6 and 7 address the implementations of the models in AMI, and the conclusions drawn from this work is presented in Section 8.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Magnesium Research and Technology Development

The Magnesium Research and Technical Development (MR&TD) project supports efforts to increase using magnesium in automotive applications, including improving technology, lowering costs and increasing the knowledge needed to enable alloy and manufacturing process optimization. MR&TD supports the U.S. Department of Energy (DOE)/United States Automotive Materials Partnership (USAMP) Magnesium Front End Research and Development (MFERD) project in collaboration with China and Canada. The MR&TD projects also maintains the magnesium bibliographic database at magnesium.pnl.gov.

36 MATERIALS SCIENCE↗

Engineering Property Prediction Tools for Tailored Polymer Composite Structures

This report summarizes our FY 2009 research activities for the project titled:"Engineering Property Prediction Tools for Tailored Polymer Composite Structures." These activities include (i) the completion of the development of a fiber length attrition model for injection-molded long-fiber thermoplastics (LFTs), (ii) development of the a fatigue damage model for LFTs and its implementation in ABAQUS, (iii) development of an impact damage model for LFTs and its implementation in ABAQUS, (iv) development of characterization methods for fatigue testing, (v) characterization of creep and fatigue responses of glass-fiber/polyamide (PA6,6) and glass-fiber/polypropylene (PP), (vi) characterization of fiber length distribution along the flow length of glass/PA6,6 and glass-fiber/PP, and (vii) characterization of impact responses of glass-fiber/PA6,6. The fiber length attrition model accurately captures the fiber length distribution along the flow length of the studied glass-fiber/PP material. The fatigue damage model is able to predict the S-N and stiffness reduction data which are valuable to the fatigue design of LFTs. The impact damage model correctly captures damage accumulation observed in experiments of glass-fiber/PA6,6 plaques.Further work includes validations of these models for representative LFT materials and a complex LFT part.

36 MATERIALS SCIENCE↗

Overview of Lightweighting Materials Research & Development in the United States FreedomCAR and Fuel Partnership

The United States of America’s (USA’s) transportation system is strongly dependent on petroleum as an energy source. Petroleum is used to satisfy 95 percent of the USA’s transportation energy needs, consuming two-thirds of all the petroleum used in the USA. Since roughly 60 percent of the petroleum is imported, the implications of this dependency on the environment and energy security are readily apparent. Since 2002, the United States Department of Energy (USDOE) and the United States Council for Automotive Research (USCAR) have worked cooperatively through the FreedomCAR and Fuel Partnership (FC&FP) to fund high-risk, high-payoff research and development (R&D) into advanced automotive technologies with the potential for lowering this dependence. The FC&FP succeeded and built upon the Partnership for a New Generation of Vehicles (PNGV) initiative that ran from 1993 to 2001.

02 PETROLEUM↗

An Integrated Approach Linking Process to Structural Modeling With Microstructural Characterization for Injections-Molded Long-Fiber Thermoplastics

The objective of our work is to enable the optimum design of lightweight automotive structural components using injection-molded long fiber thermoplastics (LFTs). To this end, an integrated approach that links process modeling to structural analysis with experimental microstructural characterization and validation is developed. First, process models for LFTs are developed and implemented into processing codes (e.g. ORIENT, Moldflow) to predict the microstructure of the as-formed composite (i.e. fiber length and orientation distributions). In parallel, characterization and testing methods are developed to obtain necessary microstructural data to validate process modeling predictions. Second, the predicted LFT composite microstructure is imported into a structural finite element analysis by ABAQUS to determine the response of the as-formed composite to given boundary conditions. At this stage, constitutive models accounting for the composite microstructure are developed to predict various types of behaviors (i.e. thermoelastic, viscoelastic, elastic-plastic, damage, fatigue, and impact) of LFTs. Experimental methods are also developed to determine material parameters and to validate constitutive models. Such a process-linked-structural modeling approach allows an LFT composite structure to be designed with confidence through numerical simulations. Some recent results of our collaborative research will be illustrated to show the usefulness and applications of this integrated approach.

36 MATERIALS SCIENCE↗

THE EFFECT OF LASER SHOCK PEENING ON THE LIFE AND FAILURE MODE OF A COLD PILGER DIE

The laser shock peening process was used to increase fatigue life of pilger dies made of A2 tool steel by imparting compressive residual stresses to fatigue prone areas of the dies. The result of X-Ray diffraction analysis indicated that deep, high- magnitude compressive residual stresses were generated by the laser shock peening process, and the peened dies exhibited a significant increase of in-service life. Fractography of the failed dies indicates that the fracture mechanism was altered by the peening process.

36 MATERIALS SCIENCE↗