Engineering Papers⌕ Search

Engineering topics

Smith, Kandler A

Publications and source records attributed to Smith, Kandler A.

At least 19 records

Field-Aging Test Bed for Behind-the-Meter PV + Energy Storage

Small DC-coupled battery test systems are deployed at the National Renewable Energy Laboratory to evaluate capacity fade models and report on performance parameters such as round-trip efficiency under indoor and outdoor deployment scenarios. Initial commercial battery products include LG Chem RESU lithium-ion (Li-ion) and Avalon vanadium redox flow batteries. Adapting indoor lab-scale test methods to outdoor systems has challenges, including maintaining constant temperature and fully controlling batteries through standard discharge curves. Initial measurements show the Li-ion battery systems performing within expectations, near 85% round-trip efficiency. Initial lifetime modeling and measurements indicate that battery capacity could degrade by 20%-35% over 10 years at current rates.

14 SOLAR ENERGY↗

Field Aging Testbed for Behind-the-Meter PV + Energy Storage

Small DC-coupled battery test systems are deployed at NREL to evaluate capacity fade models and report on performance parameters such as round-trip efficiency under indoor and outdoor deployment scenarios. Initial commercial battery products include LG Chem RESU Lithium-ion and Avalon vanadium-redox flow batteries. Adapting indoor lab-scale test methods to outdoor systems has challenges, including maintaining constant temperature and fully controlling batteries through standard discharge curves. Initial measurements show the Lithium Ion battery systems performing within expectation, near 85% round-trip efficiency. Initial lifetime modeling and measurements indicate battery capacity may degrade by 20%-35% over 10 years.

25 ENERGY STORAGE↗

Safer Batteries via Active Fault Tolerant Control

Safety remains a critical technological barrier for Lithium-ion batteries. Besides safer battery materials, intelligent battery management can be the key to safer batteries. Motivated by this scenario, we propose an active fault tolerant control scheme which can potentially improve battery safety. Essentially, we focus on battery internal thermal faults which may lead to thermal runaway, and design a control scheme to alleviate such fault effect at an early stage. The control scheme consists of a fault tolerant control algorithm coupled with a fault and state co-estimator. A multi-objective optimal control technique has been used to design the control algorithm whereas an unknown state-input co-estimation approach is used for the fault and state estimator. Finally, simulation studies illustrate the effectiveness of the proposed control scheme.

25 ENERGY STORAGE↗

Microstructure Characterization and Modeling for Improved Electrode Design

This presentation summarizes fiscal year 2018-2019 work under U.S. Department of Energy's Computer-Aided Engineering of Batteries (CAEBAT) program to develop computational tools for improved electrode design and to provide deeper fundamental understanding of the physics that limit the performance and cause degradation in lithium-ion batteries. Successes include (1) development of an electrode microstructure characterization tool box to be published open source later in 2019, (2) development of a large deformation electrochemical model capturing the volume expansion and performance limits of electrodes utilizing silicon and (3) development of a solid mechanics damage model describing the fracture of polycrystalline nickel-manganese-cobalt cathode materials with cycling.

30 DIRECT ENERGY CONVERSION↗

Understanding Impact of Local Heterogeneities During Fast Charge

Reducing battery charging time to 10 minutes would improve the market acceptance and utility of electric vehicles. Such a fast charge rate is difficult to achieve in energy-dense thick battery electrodes, however. In particular, fast charge can drive a lithium plating side reaction that is unsafe and degrades battery capacity. The onset of the lithium plating side reaction is accelerated due to non-uniformities, or heterogeneities that exist within the negative electrode active material particles, within the coating, and at larger battery length scales as well. This presentation summarizes fiscal year 2018-2019 work by NREL, Argonne National Laboratory and Purdue University in the atomistic modeling of Li transport within graphite and continuum modeling of electrochemical heterogeneities that cause early lithium plating onset. non-uniformities, or heterogeneities that exist within the negative electrode active material particles, within the coating, and at larger battery length scales as well. This presentation summarizes fiscal year 2018-2019 work by NREL, Argonne National Laboratory and Purdue University in the atomistic modeling of Li transport within graphite and continuum modeling of electrochemical heterogeneities that cause early lithium plating onset.

30 DIRECT ENERGY CONVERSION↗

Numerical investigation of thermal runaway mitigation through a passive thermal management system

Prevention of thermal runaway and its propagation remains a technical barrier to the application of lithium-ion batteries. To mitigate thermal runaway in lithium-ion battery packs, heat sinks have been designed using various materials, such as phase-change materials or metal plates. In this study, aluminum plates were assembled into battery modules as heat sinks and the effect of plate thickness on thermal runaway mitigation was numerically investigated. A three-dimensional integrated multiphysics model was validated and calibrated with experimental data. It identified the mechanism and sequence of thermal runaway propagation in detail. Thermal mass and contact resistance are found to be the key design parameters for preventing thermal runaway propagation for the studied battery module configuration. In addition, this study provides further insights into the design of aluminum heat sinks for lithium-ion battery packs.

25 ENERGY STORAGE↗

Determining Electrode Tortuosity and Rate Limitations from Experiments and Modeling

CAE models efficiently address 3D large battery performance and safety design. Further work is needed to increase electrochemical model fidelity, reduce expense of parameter ID, and integrate degradation mechanisms, enabling optimization of designs for lifetime. Microstructure models provide deeper insight into predict effective properties of macro-homogeneous models and heterogeneous utilization of electrode degradation. Enabling 10-minute fast charge of BEV200+ requires electrolytes with enhanced transport and low electrode tortuosity.

30 DIRECT ENERGY CONVERSION↗

Microstructure Characterization and Modeling for Improved Electrode Design

As part of DOE's Computer-Aided Engineering of Batteries Program, the National Renewable Energy Laboratory is developing detailed models capturing the influence of lithium-ion battery electrode design, recipe and processing on the electrode's microstructure and relating that microstructure to device-level performance. Given the difficulty in obtaining 3D microstructural images of the electrode's inert components, team member Purdue University developed an algorithm to computationally generate the so-called carbon-binder domain (CBD) for any given recipe. Mesoscale models explore the device-level impact of the CBD phase on multiple idealized and actual electrode geometries. With the inclusion of this CBD phase, microstructure models are used to predict the tortuosity of 14 different graphite and NMC electrode designs. Tortuosity predictions are shown in good agreement with experimental direct measurement and electrochemical rate studies.

25 ENERGY STORAGE↗

Micro/Macro-Scale Modeling for Battery Fast Charge Applications

In conjunction with experiments at Argonne and Idaho National Laboratories, the National Renewable Energy Laboratory is applying physics-based electrochemical models at several length-scales to understand limitations and guide design of future battery electrodes for extreme fast charge of electric vehicles. Macro-homogeneous models show that today's battery technologies must use thin electrodes to avoid electrolyte depletion and lithium plating at a 6C (10-minute) charge rate. This compromises cost and energy density however. Goals are provided for next generation electrode tortuosity and electrolyte transport requirements to achieve 6C charge in a thick electrode system. Microstructure models provide quantitative understanding of tortuosity for several graphite electrodes and further predict heterogeneous utilization of the electrodes due to their morphology.

25 ENERGY STORAGE↗

Performance and Health Test Procedure for Grid Energy Storage Systems

A test procedure to evaluate the performance and health of field installations of grid-connected battery energy storage systems (BESS) is described. Performance and health metrics captured in the procedures are: round-trip efficiency, standby losses, response time/accuracy, and useable energy/state of charge at different discharge/charge rates over the system's lifetime. The procedures are divided into reference performance tests, which require the system to be put in a test mode and are to be conducted in intervals, and real-time monitoring tests, which collect data during normal operation without interruption. The procedures can be applied on a wide array of BESS with little modification and can thus support BESS operators in the management of BESS field installations with minimal interruption and expenditure. Simulated results based on a detailed system simulation of a prototype system are provided as guideline.

25 ENERGY STORAGE↗

Quantitative Microstructure Characterization of a NMC Electrode

Performance of lithium-ion batteries (LIBs) is strongly influenced by the porous microstructure of their electrodes. In this work, 3D microstructures of calendared and un-calendared positive electrode LiNi1/3Mn1/3Co1/3O2 (NMC) have been investigated in order to extract relevant properties useful for battery modeling. Transport (volume fraction, connectivity, particle size and tortuosity) and electrochemical (specific surface area) properties have been calculated for the pore and the active material. Special attention has been paid to determine the size of the so-called representative volume element (RVE) required to be statistically representative of the heterogeneous medium. Several parameters have been calculated using a panel of different numerical methods in order to compare their results. Besides, the image level of detail has been evaluated (using original criteria based upon edge detection) to assess the overall data quality available for the study.

30 DIRECT ENERGY CONVERSION↗

Life Prediction Model for Grid-Connected Li-ion Battery Energy Storage System

Lithium-ion (Li-ion) batteries are being deployed on the electrical grid for a variety of purposes, such as to smooth fluctuations in solar renewable power generation. The lifetime of these batteries will vary depending on their thermal environment and how they are charged and discharged. To optimal utilization of a battery over its lifetime requires characterization of its performance degradation under different storage and cycling conditions. Aging tests were conducted on commercial graphite/nickel-manganese-cobalt (NMC) Li-ion cells. A general lifetime prognostic model framework is applied to model changes in capacity and resistance as the battery degrades. Across 9 aging test conditions from 0oC to 55oC, the model predicts capacity fade with 1.4% RMS error and resistance growth with 15% RMS error. The model, recast in state variable form with 8 states representing separate fade mechanisms, is used to extrapolate lifetime for example applications of the energy storage system integrated with renewable photovoltaic (PV) power generation.

25 ENERGY STORAGE↗

Efficient Simulation and Abuse Modeling of Mechanical-Electrochemical-Thermal Phenomena in Lithium-Ion Batteries

NREL's Energy Storage team is exploring the effect of mechanical crush of lithium ion cells on their thermal and electrical safety. PHEV cells, fresh as well as ones aged over 8 months under different temperatures, voltage windows, and charging rates, were subjected to destructive physical analysis. Constitutive relationship and failure criteria were developed for the electrodes, separator as well as packaging material. The mechanical models capture well, the various modes of failure across different cell components. Cell level validation is being conducted by Sandia National Laboratories.

25 ENERGY STORAGE↗

Microstructure Characterization and Modeling for Improved Electrode Design

This presentation describes research work led by NREL with team members from Argonne National Laboratory and Texas A&M University in microstructure analysis, modeling and validation under DOE's Computer-Aided Engineering of Batteries (CAEBAT) program. The goal of the project is to close the gaps between CAEBAT models and materials research by creating predictive models that can be used for electrode design.

33 ADVANCED PROPULSION SYSTEMS↗

Performance and Health Test Procedure for Grid Energy Storage Systems: Preprint

A test procedure to evaluate the performance and health of field installations of grid-connected battery energy storage systems (BESS) is described. Performance and health metrics captured in the procedures are: Round-trip efficiency, Standby losses, Response time/accuracy, and Useable Energy/ State of Charge at different discharge/charge rates over the system's lifetime. The procedures are divided into Reference Performance Tests, which require the system to be put in a test mode and are to be conducted in intervals, and Real-time Monitoring tests, which collect data during normal operation without interruption. The procedures can be applied on a wide array of BESS with little modifications and can thus support BESS operators in the management of BESS field installations with minimal interruption and expenditures.can be applied on a wide array of BESS with little modifications and can thus support BESS operators in the management of BESS field installations with minimal interruption and expenditures.

25 ENERGY STORAGE↗