Engineering Papers⌕ Search

Engineering topics

Smith, Frances N.

Publications and source records attributed to Smith, Frances N..

At least 19 records

Calcium carbonate minerals as scavengers of metals and radionuclides: Their role in natural attenuation and remediation

Calcium carbonates (CaCO3) are ubiquitous naturally occurring minerals in subsurface sediments. Calcium carbonate coatings are common in many terrestrial environments and are known to coat a variety of reactive mineral surfaces in soils and sediments, altering their reactivity and chemical behavior. For these reasons, contaminant interactions with CaCO3 minerals are relevant to contaminant fate and transport. Significant advancements have been made recently toward identifying relevant contaminant (e.g., U, I, and Cr) attenuation mechanisms, which may also serve as a basis for in situ remediation strategies. Hence, the objective of this review paper is to 1) describe the state-of-knowledge of calcium carbonate minerals as universal scavengers of metals and radionuclides; 2) provide a state of the science of how calcium carbonate interactions affect contaminant fate and transport in the subsurface environmental systems; and 2) provide insights on the use of calcium carbonate natural attenuation mechanisms and their application to the remediation of complex sites. Knowledge gaps are also identified that, when closed, can advance the use of carbonate minerals for in situ remedy applications.

Qafoku, Nikolla↗

Thermal properties of U-Mo alloys irradiated under high fission power density

A variety of physical and thermal property measurements made on irradiated U-Mo alloy monolithic fuel samples with a Zr diffusion barrier and clad in Al alloy 6061 are reported. These properties form the basis for additional investigations in thermal behavior of U-Mo fuel under high performance research reactor irradiation conditions. Measurements were performed on samples harvested from fuel plates irradiated under high fission power density and surface heat flux and complement previous measurements on samples subjected to moderate fission power density and surface heat flux. Specific heat capacity of irradiated monolithic U-Mo increases with increasing temperature and fission density, but carries large uncertainties associated with thickness measurements used to determine the mass fraction of the layer constituents for extraction of the U-Mo specific heat capacity, specifically the very thin and nonuniform Zr diffusion barrier. Density of irradiated monolithic U-Mo decreases with increasing fission density resulting from fission gas swelling and porosity formation. Thermal diffusivity of irradiated monolithic U-Mo increased with increasing temperature and decreased with increasing fission density. Thermal conductivity of irradiated monolithic U-Mo increased with increasing temperature, and in general, appeared to decrease and become less sensitive to temperature with increasing fission density. Thermal conductivity measurements compared to a semi-empirical model agreed within ±30%. It is suspected that the main driver in deviation between model calculations and measurements is the fission gas swelling determination, which does not account for fission power density or irradiation temperature.

uranium (U), molybdenum, nuclear fuel, thermal con↗

A Workshop on the History of Plutonium Processing at Hanford Washington as the Foundation for Modern-day Plutonium Process Science

Numerous national laboratories in the United States have roots related to the Manhattan Project that contributed to the end of World War II. The pioneering science and engineering that took place over the decades that followed continues to influence modern-day actinide-related research at those institutions, leading to unique strengths and cutting-edge ideas and perspectives. These same national laboratories also face a challenge: figuring out how to capture the expertise of a retiring workforce who had first-hand experience in these pioneering nuclear efforts. Recently, at PNNL a “Train-the-Trainer” approach has been piloted where mentors and mentees are paired together to develop and deliver interactive workshops on historical topics that relate to modern-day research, such as Plutonium Processing or Environmental Management of Legacy Nuclear Waste. This approach was used to develop a workshop that beings with the Historic Hanford process plutonium chemistry and engineering, describes its influence on current plutonium separation and process science, and then details the chemistry of plutonium as it progresses from a minor constituent in irradiated fuel to purified solid product. This workshop is targeted to the practitioner of applied science and technology wishing to gain a better understanding of the history and process-related chemistry of element 94 so that they may better direct the tools of their specific craft toward the present and future needs of plutonium science.

Smith, Frances N.↗

Incorporation Modes of Iodate in Calcite

Iodate incorporation in calcite is a potential sequestration pathway for environmental remediation of radioiodine-contaminated sites (e.g., Hanford Site, WA), but the mechanisms of iodate incorporation are still unknown. Molecular dynamics simulations were performed to determine the local coordination environment, the associated charge compensation schemes, and the tendency for iodate to segregate at calcite surfaces. Charge compensation by substitution of a calcium ion by either a sodium ion or a proton (i.e., the effect of pH), was considered. For charge compensation by sodium ions, a nearest-neighbor position was determined to be energetically favored, whereas for charge compensation by protons, the HIO3 molecule was found to be metastable and the formation of a bicarbonate ion was energetically favored. The iodate ion also showed a preference for the topmost atomic layer of the (104) calcite surface, which dominates the morphology of calcite crystals. Simulated trajectories were used to calculate iodine K-edge extended X-ray absorption fine structure spectra, which matched experimental data of iodate co-precipitated with calcite. The best-fit combination consisted of a significant proportion of surface-segregated iodate ions and included charge compensation by both sodium ions and protons. Therefore, an important implication is that the iodate accumulated at the surface regions of calcite crystals, may undergo mobilization under conditions that promote calcite dissolution. In addition, surface area and pH of the surrounding solution are both expected to strongly affect the extent of iodate incorporation in calcite. Hence, calcite-based iodate remediation strategies need to consider these impacts.

Kerisit, Sebastien N.↗

Importance of interlayer H bonding structure to the stability of layered minerals

Layered (oxy) hydroxide minerals often possess out-of-plane hydrogen atoms that form hydrogen bonding networks which stabilize the layered structure. However, less is known about how the ordering of these bonds affects the structural stability and solubility of these minerals. Here, we report a new strategy that uses the focused electron beam to probe the effect of differences in hydrogen bonding networks on mineral solubility. In this regard, the dissolution behavior of boehmite (γ-AlOOH) and gibbsite (γ-Al(OH)3) were compared and contrasted in real time via liquid cell electron microscopy. Under identical such conditions, 2D-nanosheets of boehmite (γ-AlOOH) exfoliated from the bulk and then rapidly dissolved, whereas gibbsite was stable. Further, substitution of only 1% Fe(III) for Al(III) in the structure of boehmite inhibited delamination and dissolution. Factors such as pH, radiolytic species, and knock on damage were systematically studied and eliminated as proximal causes for boehmite dissolution. Instead, the creation of electron/hole pairs was considered to be the mechanism that drove dissolution. The widely disparate behaviors of boehmite, gibbsite, and Fe-doped boehmite are discussed in the context of differences in the OH bond strengths, hydrogen bonding networks, and the presence or absence of electron/hole recombination centers.

58 GEOSCIENCES↗

Conceptual Model of Iodine Behavior in the Subsurface at the Hanford Site

Isotopes of iodine were generated during plutonium production within the nine production reactors at the U.S. Department of Energy Hanford Site. The short half-life 131I that was released from the fuel into the atmosphere during the dissolution process (when the fuel was dissolved) in the Hanford Site 200 Area is no longer present at concentrations of concern in the environment. The long half-life 129I generated at the Hanford Site during reactor operations was (1) stored in single-shell and double-shell tanks, (2) discharged to liquid disposal sites (e.g., cribs and trenches), (3) released to the atmosphere during fuel reprocessing operations, or (4) captured by off-gas absorbent devices (silver reactors) at chemical separations plants (PUREX, B-Plant, T-Plant, and REDOX). Releases of 129I to the subsurface have resulted in several large, though dilute, plumes in the groundwater. There is also 129I remaining in the vadose zone beneath disposal or leak locations. The fate and transport of 129I in the environment and potential remediation technologies are currently being studied as part of environmental remediation activities at the Hanford Site. A conceptual model describing the nature and extent of subsurface contamination, factors that control plume behavior, and factors relevant to potential remediation processes is needed to support environmental remedy decisions. Because 129I is an uncommon contaminant, relevant remediation experience and scientific literature are limited. In addition, its behavior in subsurface is different from that of other more common and important contaminants (e.g., U, Cr and Tc) in terms of sorption (adsorption and precipitation), and aqueous phase species transformation via redox reactions. Thus, the conceptual model also needs to both describe known contaminant and biogeochemical process information and identify aspects about which additional information is needed to effectively support remedy decisions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Developing methodologies for source attribution: glass phase separation in Trinitite using NF3

This study details thermal reactions between glasses, common minerals, and Trinitite post-detonation material with the fluorinating agent nitrogen trifluoride (NF3). The ultimate goal of our investigation is to develop a relatively rapid method for the effective separation of bomb components from complex matrices resulting from a nuclear explosion. Trinitite samples, silicate minerals (quartz; plagioclase and microcline), amorphous SiO2, calcite, a natural glass (obsidian), and two synthetic glasses were characterized extensively before and after the fluorination to fully understand the effects of the NF3 thermal treatment. Samples were reacted with NF3 using a combined thermogravimetric (TG) differential thermal analysis (DTA) unit, as well as in a stainless steel bomb reactor connected to a fluorination line. Subsequent to the NF3 treatment, samples were imaged by scanning electron microscopy in order to document changes in grain size and morphology.

Koeman, Elizabeth C.↗

Computational Investigation of Technetium(IV) Incorporation into Inverse Spinels: Magnetite (Fe 3 O 4 ) and Trevorite (NiFe 2 O 4 )

Iron oxides and oxyhydroxides play an important role in minimizing the mobility of redox-sensitive elements in engineered and natural environments. For the radionuclide technetium-99 (Tc), these phases hold promise as primary hosts for increasing Tc loading into glass waste form matrices, or as secondary sinks during the long-term storage of nuclear materials. Recent experiments show that the inverse spinel, magnetite [Fe(II)Fe(III)2O4], can incorporate Tc(IV) into its octahedral sub-lattice, and in that same class of materials, trevorite [Ni(II)Fe(III)2O4] is also being investigated for its ability to host Tc(IV). However, questions remain regarding the most energetically favorable charge-compensation mechanism for Tc(IV) incorporation in each structure, which will affect Tc behavior under changing waste processing or storage conditions. Here, quantum-mechanical methods were used to evaluate incorporation energies and optimized lattice bonding environments for three different, charge-balanced Tc(IV) incorporation mechanisms in magnetite and trevorite. In both cases, the removal of two octahedral Fe(II) or Ni(II) ions upon the addition of Tc(IV) to an octahedral site is the most stable mechanism, relative to the creation of octahedral Fe(III) defects or increasing octahedral Fe(II) content. Following hydration-energy corrections, Tc(IV) incorporation into magnetite is energetically favorable while an energy barrier exists for trevorite.

Environmental Molecular Sciences Laboratory↗

Can Cr( iii ) substitute for Al( iii ) in the structure of boehmite?

The dissolution of boehmite is a technical issue for the Al industry because of its recalcitrant nature. In fact, a similar problem exists with boehmite in nuclear waste sludge at the Hanford site in eastern Washington State, USA. Dissolution of Al phases is required to reduce the waste loadings in the final borosilicate glass waste form. Although not the most common Al-bearing species in the sludge, boehmite may become a rate limiting step in the processing of the wastes. Hanford boehmite is an order of magnitude more resistant to dissolution in hot caustic solutions than expected from surface-normalized rates. We are exploring potential intrinsic and extrinsic effects that may limit boehmite reactivity; one clue comes from microstructural analyses that indicate an association of Cr with Al in the Hanford nuclear waste. Hence, in this first paper, we investigated the potential role of chromium on the reactivity of boehmite in caustic solution. An important finding was that irrespective of the synthesis pathway, amount of Cr(III), or the resultant morphology, there was no evidence for Cr incorporation in the bulk structure, in agreement with QM calculations. In fact, electron microscopic (EM) and spectroscopic analyses showed that Cr was enriched at the (101) edges of the boehmite. However, Cr had no measurable effect on the morphology during the synthesis step. In contrast, comparison of the morphologies of the synthetic Cr-doped and pure boehmite samples after exposure to caustic solutions provided evidence that Cr inhibited the corrosion. TEM showed that Cr was not homogeneously distributed at the surface. Consequently, Cr may have partially passivated the surface by blocking discrete energetic sites on the lateral surfaces of boehmite.

1-Cra and 1-Crb↗

Technetium incorporation into goethite (α-FeOOH): An atomic-scale investigation

During the processing of low-activity radioactive waste to generate solid waste forms (e.g., glass), technetium-99 (Tc) is of concern because of its volatility. A variety of materials are under consideration to capture Tc from waste streams, including the iron oxyhydroxide, goethite (α-FeOOH), which was experimentally shown to sequester Tc(IV). This material could ultimately be incorporated into glass or other low-temperature waste form matrices. However, questions remain regarding the incorporation mechanism for Tc(IV) in goethite, which has implications for predicting the long-term stability of Tc in waste forms under changing conditions. Here, quantum-mechanical calculations were used to evaluate the energy of five different charge-compensated Tc(IV) incorporation scenarios in goethite. The two most stable incorporation mechanisms involve direct substitution of Tc(IV) onto Fe(III) lattice sites and charge balancing either by removing one nearby H+ (i.e., within 5 Å), or by creating an Fe(III) vacancy when substituting 3 Tc(IV) for 4 Fe(III), with the former being preferred over the latter relative to gas-phase ions. When corrections for hydrated references phases are applied, the Fe(III)-vacancy mechanism becomes more energetically competitive. Calculated incorporation energies and optimized bond-lengths are presented. Proton movement is observed to satisfy under-coordinated bonds surrounding vacancies in the goethite structure.

atomic-scale modeling↗

Development of On-Line Spectroscopic pH Monitoring for Nuclear Fuel Reprocessing Plants: Weak Acid Schemes

Knowledge of real-time solution properties and composition is a necessity for any spent nuclear fuel reprocessing method. Metal-ligand speciation in aqueous solutions derived from the dissolved commercial spent fuel is highly dependent upon the acid concentration/pH, which influences extraction efficiency and the resulting speciation in the organic phase. Spectroscopic process monitoring capabilities, incorporated in a counter current centrifugal contactor bank, provide a pathway for on-line real-time measurement of solution pH. The spectroscopic techniques are process-friendly and can be easily configured for on-line applications, while classic potentiometric pH measurements require frequent calibration/maintenance and have poor long-term stability in aggressive chemical and radiation environments. Our research is focused on developing a general method for on-line determination of pH of aqueous solutions through chemometric analysis of Raman spectra. Interpretive quantitative models have been developed and validated under the range of chemical composition and pH using a lactic acid/lactate buffer system. The developed model was applied to spectra obtained on-line during solvent extractions performed in a centrifugal contactor bank. The model predicted the pH within 11% for pH > 2, thus demonstrating that this technique could provide the capability of monitoring pH on-line in applications such as nuclear fuel reprocessing.

pH, spectroscopic monitoring, on-line monitoring, ↗

The Thermal Properties of Fresh and Spent U-Mo Fuels: An Overview

The evolution of the thermal conductivity of research reactor fuel during in-pile irradiation plays a significant role for the performance of the fuel element. To correctly simulate the heat fluxes and temperatures in the fuel meat during normal reactor operation and also off-normal scenarios, it is crucial to investigate the change in thermal properties, especially on the thermal conductivity, depending on the fission density and temperature. Two different U-Mo fuel types, dispersion and monolithic design, have to be considered. The thermal conductivity of fresh dispersion fuel lies between 40 and 80 W/mK depending on the particle shape, matrix material composition and U-loading. In contrast, the thermal conductivity of non-irradiated monolithic fuel is already below 15 W/mK due to the lack of the highly conductive aluminum matrix. The thermal conductivity is a composition of the thermal diffusivity, specific heat capacity and density. The specific heat capacity does not change significantly during irradiation. The density decreases slightly due to the formation of fission gas bubbles. The thermal diffusivity is strongly dependent on the materials structure. During irradiation this structure is destroyed by the fission products and fission gas bubbles. This decreases the thermal diffusivity of the irradiated material drastically down to 20% of the fresh material and has therefore the highest impact on the change of the thermal conductivity during irradiation. Therefore, during irradiation, the thermal conductivity of the dispersion fuel strongly deceases down to about 15% of the original value. The measurement of a dispersion segment from AFIP-1 with a burn-up of 6·1021f/cc yielded a thermal conductivity of 7 W/mK. The low thermal conductivity of monolithic fuel further decreases as well with increasing burn-up. At a burn-up of 3·1021f/cc, the thermal conductivity is already below 10 W/mK.

Uranium-Molybdenum, Thermal Properties, Nuclear Fu↗

Fuel Thermo-physical Characterization Project. Fiscal Year 2014 Final Report

The Office of Material Management and Minimization (M3) Reactor Conversion Fuel Thermo-Physical Characterization Project at Pacific Northwest National Laboratory (PNNL) was tasked with using PNNL facilities and processes to receive irradiated low enriched uranium–molybdenum (LEU-Mo) fuel plate samples and perform analysis in support of the M3 Reactor Conversion Program. This work is in support of the M3 Reactor Conversion Fuel Development Pillar that is managed by Idaho National Laboratory. The primary research scope was to determine the thermo-physical properties as a function of temperature and burnup. Work conducted in Fiscal Year (FY) 2014 complemented measurements performed in FY 2013 on four additional irradiated LEU-Mo fuel plate samples. Specifically, the work in FY 2014 investigated the influence of different processing methods on thermal property behavior, the absence of aluminum alloy cladding on thermal property behavior for additional model validation, and the influence of higher operating surface heat flux / more aggressive irradiation conditions on thermal property behavior. The model developed in FY 2013 and refined in FY 2014 to extract thermal properties of the U-Mo alloy from the measurements conducted on an integral fuel plate sample (i.e., U-Mo alloy with a thin Zr coating and clad in AA6061) continues to perform very well. Measurements conducted in FY 2014 on samples irradiated under similar conditions compare well to measurements performed in FY 2013. In general, there is no gross influence of fabrication method on thermal property behavior, although the difference in LEU-Mo foil microstructure does have a noticeable influence on recrystallization of grains during irradiation. Samples irradiated under more aggressive irradiation conditions, e.g., higher surface heat flux, revealed lower thermal conductivity when compared to samples irradiated at moderate surface heat fluxes, with the exception of one sample. This report documents thermal property measurements conducted in FY 2014 and compares results to values obtained from literature and measurements performed in FY 2013, where applicable, along with appropriate discussion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Conditions for critical effects in the mass action kinetics equations for water radiolysis

We report on a subtle global feature of the mass action kinetics equations for water radiolysis that results in predictions of a critical behavior in H2O2 and associated radical concentrations. While radiolysis kinetics has been studied extensively in the past, it is only in recent years that high speed computing has allowed the rapid exploration of the solution over widely varying dose and compositional conditions. We explore the radiolytic production of H2O2 under various externally fixed conditions of molecular H2 and O2 that have been regarded as problematic in the literature – specifically, “jumps” in predicted concentrations, and inconsistencies between predictions and experiments have been reported for alpha radiolysis. We computationally map-out a critical concentration behavior for alpha radiolysis kinetics using a comprehensive set of reactions. We then show that all features of interest are accurately reproduced with 15 reactions. An analytical solution for steady-state concentrations of the 15 reactions reveals regions in [H2] and [O2] where the H2O2 concentration is not unique – both stable and unstable concentrations exist. The boundary of this region can be characterized analytically as a function of G-values and rate constants independent of dose rate. Physically, the boundary can be understood as separating a region where a steady-state H2O2 concentration exists, from one where it does not exist without a direct decomposition reaction. We show that this behavior is consistent with reported alpha radiolysis data and that no such behavior should occur for gamma radiolysis. We suggest experiments that could verify or discredit a critical concentration behavior for alpha radiolysis and could place more restrictive ranges on G-values from derived relationships between them.

Wittman, Richard S.↗

LEU-Mo Fuel Out-of-Pile Characterization for TUM (Final Report)

The Technische Universität München (TUM) located in Germany requested that Pacific Northwest National Laboratory (PNNL) perform thermal-physical property measurement services for determining the thermal conductivities of irradiated U-Mo dispersion fuel samples. Two dispersion fuel segments containing U-7Mo dispersion fuel in an Al-2wt% Si matrix harvested from the AFIP-1 irradiation experiment were provided to PNNL for this effort. The segments were sectioned into samples for pycnometry (density) and laser flash analysis (thermal diffusivity), differential scanning calorimetry (specific heat capacity), and optical metallography (thickness, image analysis). This report summarizes the findings of the analysis performed at TUM’s request.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and validation of capabilities to measure thermal properties of layered monolithic U-Mo alloy plate-type fuel

The uranium-molybdenum (U-Mo) alloy in a monolithic form has been proposed as one fuel design capable of converting some of the world’s highest power research reactors from the use of high enriched uranium (HEU) to low enriched uranium (LEU). One aspect of the fuel development and qualification process is to demonstrate appropriate understanding of thermal conductivity behavior of the fuel system as a function of temperature and expected irradiation conditions. The purpose of this paper is to verify and validate the functionality of equipment methods installed in hot cells for eventual measurements on irradiated uranium-molybdenum (U-Mo) monolithic fuel specimens, procedures to operate the equipment, and models to extract the desired thermal properties. The results presented here demonstrate the adequacy of the equipment, procedures and models that have been developed for this purpose based on measurements conducted on surrogate depleted uranium-molybdenum (DU-Mo) alloy samples containing a zirconium diffusion barrier and clad in aluminum alloy 6061 (AA6061). The results are in excellent agreement with thermal property data reported in the literature for similar U-Mo alloys as a function of temperature.

multi-layer↗