Engineering Papers⌕ Search

Engineering topics

Smith, D. M.

Publications and source records attributed to Smith, D. M..

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Analysis of gap heating due to stepped tiles in the shuttle thermal protection system

Analytical methods used to investigate entry gap heating in the Shuttle orbiter thermal protection system are described. Analytical results are given for a fuselage lower-surface location and a wing lower-surface location. These are locations where excessive gap heating occurred on the first flight of the Shuttle. The results of a study to determine the effectiveness of a half-height ceramic fiber gap filler in preventing hot-gas flow in the tile gaps are also given.

Petley, D. H.↗
NASA NTRS1983

An investigation of gap heating due to stepped tiles in zero pressure gradient regions of the Shuttle Orbiter Thermal Protection System

An analytical study is presented which investigates the cause of the excessive heating in the tile-to-tile gaps of the Shuttle Orbiter Thermal Protection System, as evidenced by the visible discoloration and charring of the filler bar and strain isolation pad used in the attachment of tiles to the aluminum substrate. Techniques are developed to estimate the pressure disturbances due to a stepped tile and to calculate the disturbance-induced mass flow rates in the tile-to-tile gaps, filler bar, strain isolation pad, and the tile itself. A thermal analysis in the tile-to-tile gap is then performed in order to determine the temperature response to the hot gas flow. Calculations are performed at locations on the fuselage and the left wing where damaged filler bars were observed on the first flight of the Shuttle. It is concluded that the steps and gaps must be controlled within tight tolerances during tile installation and the tolerances must be maintained in flight. If the tolerances cannot be maintained, tile-to-tile gap filler may be an alternative.

Smith, D. M.↗
NASA NTRS1980

Analysis and design of a ceramic nozzle insert for the Langley 8-foot high temperature structures tunnel

An analysis is presented of various ceramic design concepts intended to improve nozzle throat life and tunnel performance in the hypersonic Langley 8-Foot High-Temperature Structures Tunnel, which uses methane-air combustion products as the wind-tunnel test medium. Calculations of the axial pressure distribution and heating rates in the air-cooled nozzle throat are presented, and desirable characteristics of a ceramic material to be used in the nozzle throat are outlined, including high-temperature strength, thermal shock and erosion resistance, low conductivity and low thermal expansion. Ceramic nozzle throat design concepts are then examined, with attention given to monolithic and layered constructions of cast ceramics, reaction-bonded materials and a fiber-reinforced silica-silica ceramic. Results of a finite element analysis of the temperatures and stresses characteristic of the various concepts are then presented which indicate the monolithic silica-silica and the layered silica-silica/reaction bonded silicon nitride concepts to be the most promising of those investigated.

Robinson, J. C.↗
NASA NTRS1977

Optimization guide for programs compiled under IBM FORTRAN H (OPT=2)

Guidelines are given to provide the programmer with various techniques for optimizing programs when the FORTRAN IV H compiler is used with OPT=2. Subroutines and programs are described in the appendices along with a timing summary of all the examples given in the manual.

Smith, D. M.↗
NASA NTRS1973

Bibliography of information on mechanics of structural failure

A bibliography of approximately 1500 reference citations related to six problem areas in the mechanics of failure in aerospace structures is presented. The bibliography represents a search of the literature published in the ten year period 1962-1972 and is largely limited to documents published in the United States. Listings are subdivided into the six problem areas: (1) life prediction of structural materials; (2) fracture toughness data; (3) fracture mechanics analysis; (4) hydrogen embrittlement; (5) protective coatings; and (6) composite materials. An author index is included.

Carpenter, J. L., Jr.↗
NASA NTRS1971

Analog tree-organized multiplexer

An analog tree-organized multiplexer (ATOM) which is intended for use in the telemetry system of an interplanetary spacecraft is designed. The ATOM will be fabricated by a monolithic, dielectric isolation process, and will contain silicon junction field effect transistors (JFET) as the active elements. The effect of the radiation environment on the performance of the ATOM is analyzed. The result indicates that the expected radiation environment will cause only minor changes in the preradiation characteristics of ATOM. The JFET in the ATOM is designed to meet the electrical requirements when fabricated by either the double poly-dielectric isolation process or the raised dielectric isolation process. The effect of the heat treatment required for the dielectric isolation process on the diffusion profile of the JFET is described. The layout of the ATOM circuit for fabrication by either the double poly or raised dielectric isolation process is also given.

Crabbe, J. S.↗