Engineering Papers⌕ Search

Engineering topics

Sim, A. G.

Publications and source records attributed to Sim, A. G..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A comparison of Wortmann airfoil computer-generated lift and drag polars with flight and wind tunnel results

Computations of drag polars for a low-speed Wortmann sailplane airfoil are compared with both wind tunnel and flight test results. Excellent correlation was shown to exist between computations and flight results except when separated flow regimes were encountered. Smoothness of the input coordinates to the PROFILE computer program was found to be essential to obtain accurate comparisons of drag polars or transition location to either the flight or wind tunnel flight results.

Bowers, A. H.↗
NASA NTRS1984

In-flight total forces, moments and static aeroelastic characteristics of an oblique-wing research airplane

A low-speed flight investigation has provided total force and moment coefficients and aeroelastic effects for the AD-1 oblique-wing research airplane. The results were interpreted and compared with predictions that were based on wind tunnel data. An assessment has been made of the aeroelastic wing bending design criteria. Lateral-directional trim requirements caused by asymmetry were determined. At angles of attack near stall, flow visualization indicated viscous flow separation and spanwise vortex flow. These effects were also apparent in the force and moment data.

Curry, R. E.↗
NASA NTRS1984

Flight-determined aerodynamic derivatives of the AD-1 oblique-wing research airplane

The AD-1 is a variable-sweep oblique-wing research airplane that exhibits unconventional stability and control characteristics. In this report, flight-determined and predicted stability and control derivatives for the AD-1 airplane are compared. The predictions are based on both wind tunnel and computational results. A final best estimate of derivatives is presented.

Sim, A. G.↗
NASA NTRS1984

Flight characteristics of a manned, low-speed, controlled deep stall vehicle

A successful manned, low speed, controlled deep stall flight research program was conducted at NASA Ames Research Center's Dryden Flight Research Facility. Piloting techniques were established that enabled the pilot to attain and stabilize on an angle of attack in the 30 deg to 72 deg range. A flight determined aerodynamic data base was established for angles of attack as high as 72 deg. Poor lateral directional flying qualities were encountered at angles of attack above 60 deg. Insight into the high angle of attack lateral directional dynamics was gained through a basic root locus analysis.

Sim, A. G.↗
NASA NTRS1984

Flight characteristics of a manned, low-speed, controlled deep stall vehicle

A successful manned, low-speed, controlled deep stall flight research program was conducted at NASA Ames Research Center's Dryden Flight Research Facility. Piloting techniques were established that enabled the pilot to attain and stabilize on an angle of attack in the 30 to 72 deg range. A flight-determined aerodynamic data base was established for angles of attack as high as 72 deg. Poor lateral-directional flying qualities were encountered at angles of attack above 60 deg. Insight into the high angle-of-attack, lateral-directional dynamics was gained through a basic root-locus analysis.

Sim, A. G.↗
NASA NTRS1982

Unique flight characteristics of the AD-1 oblique-wing research airplane

Flight characteristics associated with an oblique-wing airplane have been studied with limited scope and complexity using the AD-1 research vehicle. The AD-1 is a low-speed, low-cost, manned airplane with an aeroelastically tailored wing that can be pivoted 0 to 60 deg asymmetrically. Results of the flight tests include aerodynamic parameter extraction, verification of the aeroelastic wing design criteria, trim requirements, stall characteristics, and an evaluation of the handling qualities and basic control system requirements. Some of the unique characteristics of these results that pertain to the oblique-wing design are presented.

Curry, R. E.↗
NASA NTRS1981

AD-1 oblique wing aircraft program

A NASA program for evaluation of the handling and flying characteristics of the AD-1 oblique wing aircraft is discussed. The vehicle was flown to compare wind tunnel predictions with aerodynamic data, explore the control system requirements, and obtain a preliminary assessment of the aeroelastic effects. The fiberglass sandwich skin aircraft is designed for 8 g positive and 4 g negative loading at 175 knots, while the wing pivot can withstand 25 g loading. Flight monitoring was accomplished with a 41 channel pulse code modulation system for telemetry and by averaging of pilot ratings. Maneuvering tests are outlined, noting that pilot ratings indicated acceptable handling at up to 50 deg sweep. It is concluded that acceptable flying qualities can be achieved with a 60 deg sweep, and that aeroelastic tailoring can be used to satisfy cruise design technology.

Mcmurtry, T. C.↗
NASA NTRS1980

AD-1 oblique wing aircraft program

The oblique wing concept for super- and subsonic transport was assessed by analysis and wind tunnel radio control model and remotely piloted vehicle testing. A one-sixth scale wind tunnel model and a low speed manned oblique wing research airplane (AD-1) were developed. Model wind tunnel test data on dynamic structural response characteristics were used in a simulator to develop the control system. The airplane is of simple design with fiber glass skin, weight of approximately 2100 lbs and speeds of up to 175 knots at altitudes up to 15,000 ft. Flight testing will investigate handling and flying qualities, oblique wing flight control characteristics, aeroelastic wing design and will compare actual with predicted aerodynamic characteristics. Nineteen flights were made at 12,000 to 13,000 feet with speeds of 100-160 knots. Flutter clearance as a function of wing sweep angle is now under investigation.

Andrews, W. H.↗
NASA NTRS1978

Flight-determined stability and control derivatives for the F-111 Tact research aircraft

A flight investigation was conducted to provide a stability and control derivative data base for the F-111 transonic aircraft technology research aircraft. Longitudinal and lateral-directional data were obtained as functions of Mach number, angle of attack, and wing sweep. For selected derivatives, the flight results were correlated with derivatives calculated based on vehicle geometry. The validity of the angle of attack measurement was independently verified at a Mach number of 0.70 for angles of attack between 3 and 10 degrees.

Sim, A. G.↗
NASA NTRS1975

Flight evaluation of the M2-F3 lifting body handling qualities at Mach numbers from 0.30 to 1.61

Percentage distributions of 423 pilot ratings obtained from 27 flights are used to indicate the general level of handling qualities of the M2-F3 lifting body. Percentage distributions are compared on the basis of longitudinal and lateral-directional handling qualities, control system, control system status, and piloting task. Ratings of longitudinal handling qualities at low speed were slightly better than those for transonic and supersonic speed. The ratings of lateral-directional handling qualities were unaffected by speed and configuration. Specific handling qualities problems are discussed in detail, and comparisons are made with pertinent handling qualities criteria.

Kempel, R. W.↗
NASA NTRS1973

Flight-determined stability and control characteristics of the M2-F3 lifting body vehicle

Flight data were obtained over a Mach number range from 0.4 to 1.55 and an angle-of-attack range from -2 deg to 16 deg. Lateral-directional and longitudinal derivatives, reaction control rocket effectiveness, and longitudinal trim information obtained from flight data and wind-tunnel predictions are compared. The effects of power, configuration change, and speed brake are discussed.

Sim, A. G.↗
NASA NTRS1973

Results of a feasibility study using the Newton-Raphson digital computer program to identify lifting body derivatives from flight data

A brief study was made to assess the applicability of the Newton-Raphson digital computer program as a routine technique for extracting aerodynamic derivatives from flight tests of lifting body types of vehicles. Lateral-direction flight data from flight tests of the HL-10 lifting body reserch vehicle were utilized. The results in general, show the computer program to be a reliable and expedient means for extracting derivatives for this class of vehicles as a standard procedure. This result was true even when stability augmentation was used. As a result of the study, a credible set of HL-10 lateral-directional derivatives was obtained from flight data. These derivatives are compared with results from wind-tunnel tests.

Sim, A. G.↗