Engineering Papers⌕ Search

Engineering topics

Shvarts, D

Publications and source records attributed to Shvarts, D.

Experimental observations of turbulent mixing due to Kelvin-Helmholtz instability on the OMEGA Laser Facility

Shear-flow, Kelvin-Helmholtz (KH) turbulent mixing experiments were performed on the OMEGA Laser Facility [Boehly et al., Opt. Commun. 133, 495 (1997)] in which laser-driven shock waves propagated through a low-density plastic foam placed on top of a higher-density plastic foil. The plastic foil was comprised a thin iodine-doped plastic tracer layer bonded on each side to an undoped density-matched polyamide-imide plastic. Behind the shock front, lower-density foam plasma flowed over the higher-density plastic plasma, such that the interface between the foam and plastic was KH unstable. The initial perturbations consisted of pre-imposed, sinusoidal 2D perturbations, and broadband 3D perturbations due to surface roughness at the interface between the plastic and foam. KH instability growth was measured using side-on radiography with a point-projection 5-keV vanadium backlighter. Time-integrated images were captured on D-8 x-ray film. Spatial density profiles of iodine-doped plastic mixed with foam were inferred using x-ray radiographs. The mixing layer ensuing from the KH instability with layer width up to {approx}100 {mu}m was observed at a location {approx}1 mm behind the shock front. The measured mixing layer width was in good agreement with predictions based on a simple self-similar model of KH instability growth using an estimate of the shear velocity obtained from numerical simulations of the experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shock-tuned cryogenic-deuterium-tritium implosion performance on Omega

Cryogenic-deuterium-tritium (DT) target compression experiments with low-adiabat (alpha), multiple-shock drive pulses have been performed on the Omega Laser Facility [T. R. Boehly, D. L. Brown, R. S. Craxton et al., Opt. Commun. 133, 495 (1997)] to demonstrate hydrodynamic-equivalent ignition performance. The multiple-shock drive pulse facilitates experimental shock tuning using an established cone-in-shell target platform [T. R. Boehly, R. Betti, T. R. Boehly et al., Phys. Plasmas 16, 056301 (2009)]. These shock-tuned drive pulses have been used to implode cryogenic-DT targets with peak implosion velocities of 3x10{sup 7} cm/s at peak drive intensities of 8x10{sup 14} W/cm{sup 2}. During a recent series of alphaapprox2 implosions, one of the two necessary conditions for initiating a thermonuclear burn wave in a DT plasma was achieved: an areal density of approximately 300 mg/cm{sup 2} was inferred using the magnetic recoil spectrometer [J. A. Frenje, C. K. Li, F. H. Seguin et al., Phys. Plasmas 16, 042704 (2009)]. The other condition--a burn-averaged ion temperature <T{sub i}>{sub n} of 8-10 keV--cannot be achieved on Omega because of the limited laser energy; the kinetic energy of the imploding shell is insufficient to heat the plasma to these temperatures. A <T{sub i}>{sub n} of approximately 3.4 keV would be required to demonstrate ignition hydrodynamic equivalence [Betti et al., Phys. Plasmas17, 058102 (2010)]. The <T{sub i}>{sub n} reached during the recent series of alphaapprox2 implosions was approximately 2 keV, limited primarily by laser-drive and target nonuniformities. Work is underway to improve drive and target symmetry for future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermonuclear ignition in inertial confinement fusion and comparison with magnetic confinement

The physics of thermonuclear ignition in inertial confinement fusion (ICF) is presented in the familiar frame of a Lawson-type criterion. The product of the plasma pressure and confinement time Ptau for ICF is cast in terms of measurable parameters and its value is estimated for cryogenic implosions. An overall ignition parameter chi including pressure, confinement time, and temperature is derived to complement the product Ptau. A metric for performance assessment should include both chi and Ptau. The ignition parameter and the product Ptau are compared between inertial and magnetic-confinement fusion. It is found that cryogenic implosions on OMEGA[T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have achieved Ptauapprox1.5 atm s comparable to large tokamaks such as the Joint European Torus [P. H. Rebut and B. E. Keen, Fusion Technol. 11, 13 (1987)] where Ptauapprox1 atm s. Since OMEGA implosions are relatively cold (Tapprox2 keV), their overall ignition parameter chiapprox0.02-0.03 is approx5x lower than in JET (chiapprox0.13), where the average temperature is about 10 keV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tgermonuclear Ignition in Inertial Confinement Fusion and Comparison with Magnetic Confinement

The physics of thermonuclear ignition in inertial confinement fusion (ICF) is presented in the familiar frame of a Lawson-type criterion. The product of the plasma pressure and confinement time Ptau for ICF is cast in terms of measurable parameters and its value is estimated for cryogenic implosions. An overall ignition parameter chi including pressure, confinement time, and temperature is derived to complement the product Ptau. A metric for performance assessment should include both chi and Ptau. The ignition parameter and the product Ptau are compared between inertial and magnetic-confinement fusion. It is found that cryogenic implosions on OMEGA [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have achieved Ptau ~ 1.5 atm s comparable to large tokamaks such as the Joint European Torus [P. H. Rebut and B. E. Keen, Fusion Technol. 11, 13 (1987)] where Ptau ~ 1 atm s. Since OMEGA implosions are relatively cold (T ~ 2 keV), their overall ignition parameter chi ~ 0.02–0.03 is ~5X lower than in JET (chi ~ 0.13), where the average temperature is about 10 keV.

Betti, R↗

Generalized Measurable Ignition Criterion for Inertial Confinement Fusion

A multidimensional measurable criterion for central ignition of inertial-confinement-fusion capsules is derived. The criterion accounts for the effects of implosion nonuniformities and depends on three measurable parameters: the neutron-averaged total areal density (pRn^tot), the ion temperature (Tn), and the yield over clean (YOC = ratio of the measured neutron yield to the predicted one-dimensional yield). The YOC measures the implosion uniformity. The criterion can be approximated by chi = (pRn^tot)^0.8 x (Tn/4.7)^1.7 YOC^u > 1 (where pR is in g cm^-2, T in keV, and u ~~0.4–0.5) and can be used to assess the performance of cryogenic implosions on the NIF and OMEGA. Cryogenic implosions on OMEGA have achieved chi ~ 0.02–0.03.

Chang, P Y↗

Neutron Yield Study of Direct-Drive, Low-Adiabat Cryogenic D2 Implosions on OMEGA Laser System

Neutron yields of direct-drive, low-adiabat (alpha ~~ 2 to 3) cryogenic D2 target implosions on the OMEGA laser system [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have been systematically investigated using the two-dimensional (2D) radiation hydrodynamics code DRACO [P. B. Radha et al., Phys. Plasmas 12, 056307 (2005)]. Low-mode (ell <- 12) perturbations, including initial target offset, ice-layer roughness, and laser-beam power imbalance, were found to be the primary source of yield reduction for thin-shell (5 um), low-alpha, cryogenic targets. The 2D simulations of thin-shell implosions track experimental measurements for different target conditions and peak laser intensities ranging from 2.5 x 10^14–6 x 10^14 W/cm^2. Simulations indicate that the fusion yield is sensitive to the relative phases between the target offset and the ice-layer perturbations. The results provide a reasonable good guide to understanding the yield degradation in direct-drive, low-adiabat, cryogenic, thin-shell-target implosions. Thick-shell (10 um) implosions generally give lower yield over clean than low-ell-mode DRACO simulation predictions. Simulations including the effect of laser-beam nonuniformities indicate that high-ell-mode perturbations caused by laser imprinting further degrade the neutron yield of thick-shell implosions. To study ICF compression physics, these results suggest a target specification with a <-30 um offset and ice-roughness of sigma_rms < 3 um are required.

Hu, S X↗

Spherical Rayleigh-Taylor growth of three-dimensional broadband perturbations on OMEGA

Spherical Rayleigh-Taylor (RT) growth experiments of three-dimensional (3D) broadband nonuniformities were conducted in the acceleration phase of spherical implosions on OMEGA [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. The targets consisted of 20- and 24-{mu}m-thick plastic spherical shells having diagnostic openings for backlighter x rays to image shell modulations. Experiments were conducted with square laser pulses at a low drive intensity of {approx}2x10{sup 14} W/cm{sup 2}, high drive intensity of {approx}1x10{sup 15} W/cm{sup 2}, and a shaped pulse consisting of a low-intensity foot and high-intensity drive part (peak intensity of {approx}1x10{sup 15} W/cm{sup 2}). In low-intensity experiments, large RT growth was measured, resulting in shells being broken up by 3D modulations at the end of the drive. In the high-intensity experiments, no RT growth of the 3D modulations was detected. In the shaped-pulse experiments, perturbations grew during the low-intensity part of the drive and were stabilized later during the high-intensity part of the drive. The measured RT growth stabilization with the high-intensity drive was similar to previous observations in planar geometry [V. A. Smalyuk et al., Phys. Rev. Lett. 101, 025002 (2008)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rayleigh-Taylor Growth Measurements in the Acceleration Phase of Spherical Implosions on OMEGA

The Rayleigh-Taylor (RT) growth of 3D broadband nonuniformities was measured using x-ray radiography in spherical plastic shells accelerated by laser light at an intensity of ~2 x 10^14 W/cm^2. The 20- and 24-um-thick spherical shells were imploded with 54 beams on the OMEGA laser system. The shells contained diagnostic openings for backlighter x rays used to image shell modulations. The measured shell trajectories and modulation RT growth were in fair agreement with 2D hydro simulations during the acceleration phase of the implosions with convergence ratios of up to ~2:2. Since the ignition designs rely on these simulations, improvements in the numerical codes will be implemented to achieve better agreement with experiments.

Smalyuk, V A↗

Proton radiography of dynamic electric and magnetic fields in laser-produced high-energy-density plasmas

Time-gated, monoenergetic-proton radiography provides unique measurements of the electric (E) and magnetic (B) fields produced in laser-foil interactions and during the implosion of inertial-confinement-fusion capsules. These experiments resulted in the first observations of several new and important features: (1) observations of the generation, decay dynamics, and instabilities of megagauss B fields in laser-driven planar plastic foils, (2) the observation of radial E fields inside an imploding capsule, which are initially directed inward, reverse direction during deceleration, and are likely related to the evolution of the electron pressure gradient, and (3) the observation of many radial filaments with complex electromagnetic field striations in the expanding coronal plasmas surrounding the capsule. The physics behind and implications of such observed fields are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cryogneic-Target Performance and Implosion Physics Studies on OMEGA

Recent progress in direct-drive cryogenic implosions on the OMEGA Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reviewed. Ignition-relevant areal densities of ~200 mg/cm^2 in cryogenic D2 implosions with peak laser-drive intensities of ~5 x 10^14 W/cm^2 were previously reported [T. C. Sangster et al., Phys. Rev. Lett. 100, 185006 (2008)]. The laser intensity is increased to ~10^15 W/cm^2 to demonstrate ignition-relevant implosion velocities of 3–4 x 10^7 cm/ s, providing an understanding of the relevant target physics. Planar-target acceleration experiments show the importance of the nonlocal electron-thermal-transport effects for modeling the laser drive. Nonlocal and hot-electron preheat is observed to stabilize the Rayleigh–Taylor growth at a peak drive intensity of ~10^15 W/cm^2. The shell preheat caused by hot electrons generated by two-plasmon-decay instability was reduced by using Si-doped ablators. The measured compressibility of planar plastic targets driven with high-compression shaped pulses agrees well with one-dimensional simulations at these intensities. Shock mistiming has contributed to compression degradation of recent cryogenic implosions driven with continuous pulses. Multiple-picket (shock-wave) target designs make it possible for a more robust tuning of the shock-wave arrival times. Cryogenic implosions driven with double-picket pulses demonstrate somewhat improved compression performance at a peak drive intensity of ~10^15 W/cm^2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Validation of Thermal-Transport Modeling with Direct-Drive, Planar-Foil Acceleration Experiments on OMEGA

We present for the first time the experimental validation of the nonlocal thermal-transport model for a National Ignition Facility relevant laser intensity of ~10^15 W/cm^2 on OMEGA. The measured thin target trajectories are in good agreement with predictions based on the nonlocal model over the full range of laser intensities from 2 x 10^14 to 10^15 W/cm^2. The standard local thermal-transport model with a constant flux limiter of 0.06 disagrees with experimental measurements at a high intensity of ~10^15 W/cm^2 but agrees at lower intensities. These results show the significance of nonlocal effects for direct-drive ignition designs.

Hu, S X↗

Shock Ignition of Thermonuclear Fuel with High Areal Densities

In thick shell implosions, most of the kinetic energy is used to assemble the cold fuel rather than to heat the hot spot. A significant increase in the hot-spot compression and reduction of the driver energy required for ignition can be accomplished by launching a shock during the final stage of the implosion. In direct-drive inertial confinement fusion (ICF), the “ignitor” shock can be launched by a power spike at the end of the laser pulse. For targets with the same adiabat and implosion velocities, the laser energy required for ignition is significantly lower for shock-ignition ICF than for standard ICF.

Betti, R↗

Rayleigh-Taylor Growth Stabilization in Direct-Drive Plastic Targets at Laser Intensities of ~1 x 10^15 W/cm^2

Direct-drive, planar-target Rayleigh-Taylor growth experiments were performed for the first time to test fundamental physics in hydrocodes at peak drive intensities of ignition designs. The unstable modulation growth at a drive intensity of ~1 X 10^15 W/cm^2 was strongly stabilized compared to the growth at an intensity of ~5 x 10^14 W/cm^2. The experiments demonstrate that standard simulations based on a local model of electron thermal transport break down at peak intensities of ignition designs (although they work well at lower intensities). The preheating effects by nonlocal electron transport and hot electrons were identified as some of the stabilizing mechanisms.

Smalyuk, V A↗

The Role of Fast-Electron Preheating in Low-Adiabat Cryogenic Implosions on OMEGA

The compression in direct-drive, low-adiabat spherical implosions was studied using cryogenic D2 targets on the 60-beam, 351-nm OMEGA laser in the range of laser intensities from ~3 x 10^14 to ~1.5 x 10^15 W/cm^2. The neutron-burn–averaged areal densities decreased as the laser intensity increased. This decrease in areal density is highly correlated with the increased hard-x-ray signals, caused by hot electrons generated by the two-plasmon-decay instability. The areal-density reduction up to ~2, observed in the experiments, requires a preheat energy of ~60 J (~0.3% of total laser energy), which is consistent with the estimated preheat levels inferred from the hard-x-ray signal levels. Mitigating the generation of fast-electrons results in high areal densities which are close to the 1D predictions.

Shvarts, D↗

Modeling High-Compression, Direct-Drive, ICF Experiments

The success of direct-drive-ignition target designs depends on two issues: the ability to maintain the main fuel entropy at a low level and the control of the nonuniformity growth during the implosion. Modelling the ICF experiments requires an accurate account for all sources of shell heating, including the shock heating, radiation and suprathermal electrons preheat, and small-scale perturbation growth. To increase calculation accuracy, a new heat-transport model has been developed and implemented in the 1-D hydrocode LILAC. This model includes both the effect of the resonance absorption and the nonlocal thermal transport. The OMEGA experiments designed with the help of the new model have achieved high-areal-density pR > 200 mg/cm^2) fuel assembly in the low-adiabat cryogenic shell implosions.

Goncharov, V N↗