Engineering Papers⌕ Search

Engineering topics

Shuart, M. J.

Publications and source records attributed to Shuart, M. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Effects of cutouts on the behavior of symmetric composite laminates subjected to bending and twisting loads

Composite structures are used for a wide variety of aerospace applications. Practical structures contain cutouts and these structures are subjected to in-plane and out-of-plane loading conditions. Structurally efficient designs for composite structures require a thorough understanding of the effects of cutouts on the response of composite plates subjected to inplane or out-of-plane loadings. Most investigations of the behavior of composite plates with cutouts have considered in-plane loadings only. Out-of-plane loadings suchas bending or twisting have received very limited attention. The response of homogeneous plates (e.g., isotropic or orthotropic plates) subjected to bending or twisting moments has been studied analytically. These analyses are for infinite plates and neglect finite-plate effects. Recently, analytical and experimental studies were conducted to determine the effects of cutouts on the response of laminated composite plates subjected to bending moments. No analytical or experimental results are currently available for the effects of cutouts on the response of composite laminates subjected to twisting moments.

Prasad, C. B.↗
NASA NTRS1993

Technology integration box beam failure study

Composite structures have the potential to be cost-effective, structurally efficient primary aircraft structures. The Advanced Composites Technology (ACT) Program has the goal to develop the technology to exploit this potential for heavily loaded aircraft structures. As part of the ACT Program, Lockheed Aeronautical Systems Company completed the design and fabrication of the Technology Integration Box Beam (TIBB). The TIBB is an advanced composite prototype structure for the center wing section of the C-130 aircraft. Lockheed subjected the TIBB to downbending, upbending, torsion and combined upbending and torsion load conditions to verify the design. The TIBB failed at 83 percent of design ultimate load for the combined upbending and torsion load condition. The objective of this paper is to describe the mechanisms that led to the failure of the TIBB. The results of a comprehensive analytical and experimental study are presented. Analytical results include strain and deflection results from both a global analysis of the TIBB and a local analysis of the failure region. These analytical results are validated by experimental results from the TIBB tests. The analytical and experimental results from the TIBB tests are used to determine a sequence of events that resulted in failure of the TIBB. A potential cause of failure is high stresses in a stiffener runout region. Analytical and experimental results are also presented for a stiffener runout specimen that was used to simulate the TIBB failure mechanisms.

Shuart, M. J.↗
NASA NTRS1992

Compression failure of angle-ply laminates

Test results from the compression loading of (+ or - Theta/ - or + Theta)(sub 6s) angle-ply IM7-8551-7a specimens, 0 less than or = Theta less than or = 90 degs, are presented. The observed failure strengths and modes are discussed, and typical stress-strain relations shown. Using classical lamination theory and the maximum stress criterion, an attempt is made to predict failure stress as a function of Theta. This attempt results in poor correlation with test results and thus a more advanced model is used. The model, which is based on a geometrically nonlinear theory, and which was taken from previous work, includes the influence of observed layer waviness. The waviness is described by the wave length and the wave amplitude. The theory is briefly described and results from the theory are correlated with test results. It is shown that by using levels of waviness observed in the specimens, the correlation between predictions and observations is good.

Peel, L. D.↗
NASA NTRS1992

Analysis of multifastener composite joints

A new numerical procedure for determining load proportioning in multiple-hole mechanical joints in composite plates is presented. The joints are loaded in double lap fashion in tension with pins through the holes. The commercial finite-element program ABAQUS is used to predict the load proportioning among holes using two independent plane stress finite-element models, one representing the composite inner lap and one representing the two steel outer laps, interacting through rigid circular surfaces. The circular surfaces effectively represent rigid pins. Load proportioning is predicted for a number of geometries. Excellent correlation with experimental data is obtained. Experimental and computed surface strains are also found to compare well. The assumption of a radial cosine distribution of contact stress between pin and hole is shown to be substantially in error for some holes.

Griffin, O. H., Jr.↗
NASA NTRS1991

Experimental behavior of graphite-epoxy Y-stiffened specimens loaded in compression

An experimental investigation of the behavior of graphite-epoxy Y-stiffened specimens loaded in compression is presented. Experimental results are presented for element specimens with a single stiffener and for panel specimens with three stiffeners. Response and failure characteristics of the specimens are described. Effects of impact damage on structural response for both specimen configurations are also presented. Results indicate that impact location may significantly affect the residual strength of the Y-stiffened specimens. The failure results indicate that the critical failure mode is buckling of the stiffener webs for Y-stiffened element specimens and buckling of both stiffener web and stiffener blade for the Y-stiffened panel specimens.

Sydow, P. D.↗
NASA NTRS1990

A Protection And Detection Surface (PADS) for damage tolerance

A protection and detection surface (PADS) concept was studied for application to composite primary aircraft structures. A Kevlar-epoxy woven face sheet with a Rohacell foam core was found to be the most effective PADS configuration among the configurations evaluated. The weight of the PADS configuration was estimated to be approximately 17 percent of the structural weight. The PADS configuration was bonded to graphite-epoxy base laminates, and up to a 70 percent improvement in compression-after-impact failure strains was observed.

Shuart, M. J.↗
NASA NTRS1990

Analysis and experiments for composite laminates with holes and subjected to 4-point bending

Analytical and experimental results are presented for composite laminates with a hole and subjected to four-point bending. A finite-plate analysis is used to predict moment and strain distributions for six-layer quasi-isotropic laminates and transverse-ply laminates. Experimental data are compared with the analytical results. Experimental and analytical strain results show good agreement for the quasi-isotropic laminates. Failure of the two types of composite laminates is described, and failure strain results are presented as a function of normalized hole diameter. The failure results suggest that the initial failure mechanism for laminates subjected to four-point bending are similar to the initial failure mechanisms for corresponding laminates subjected to uniaxial inplane loadings.

Shuart, M. J.↗
NASA NTRS1989

Moment distributions around holes in symmetric composite laminates subjected to bending moments

An analytical investigation of the effects of holes on the moment distribution of symmetric composite laminates subjected to bending moments is described. A general, closed-form solution for the moment distribution of an infinite anisotropic plate is derived, and this solution is used to determine stress distributions both on the hole boundary and throughout the plate. Results are presented for several composite laminates that have holes and are subjected to either pure bending or cylindrical bending. Laminates with a circular hole or with an elliptical hole are studied. Laminate moment distributions are discussed, and ply stresses are described.

Prasad, C. B.↗
NASA NTRS1986

Compression-Failure Mechanisms in Composite Laminates

Failure mechanisms observed using transparent fiberglass/epoxy birefringent materials. Technique based on use of transparent fiberglass/epoxy birefringent material. Transparency allows visual observation of location of initial laminate failure and of subsequent failure propagation; birefringence allows laminate stress distribution to be observed during test and also after test if permanent residual stresses occur. Nondestructive technique developed to observe failure as it develops and as propagates within laminate.

Shuart, M. J.↗
NASA NTRS1985

Short-wavelength buckling and shear failures for compression-loaded composite laminates

The short-wavelength buckling (or the microbuckling) and the interlaminar and inplane shear failures of multi-directional composite laminates loaded in uniaxial compression are investigated. A laminate model is presented that idealizes each lamina. The fibers in the lamina are modeled as a plate, and the matrix in the lamina is modeled as an elastic foundation. The out-of-plane w displacement for each plate is expressed as a trigonometric series in the half-wavelength of the mode shape for laminate short-wavelength buckling. Nonlinear strain-displacement relations are used. The model is applied to symmetric laminates having linear material behavior. The laminates are loaded in uniform end shortening and are simply supported. A linear analysis is used to determine the laminate stress, strain, and mode shape when short-wavelength buckling occurs. The equations for the laminate compressive stress at short-wavelength buckling are dominated by matrix contributions.

Shuart, M. J.↗
NASA NTRS1984

Investigating compression failure mechanisms in composite laminates with a transient fiberglass-epoxy birefringent material

An experimental study is reported in which a nondestructive technique involving the use of a transparent fiberglass-epoxy composite birefringent material has been used to investigate compression failure mechanisms in graphite-epoxy laminates. It is shown that the birefringency and transparency of the fiberglass-epoxy material permits regions of high stress to be located and the mechanisms of local failure propagation to be identified within the laminate. The material may also be useful for studying stress fields and for identifying failure initiation and propagation mechanisms in a wide variety of composite-structure problems.

Shuart, M. J.↗
NASA NTRS1984

Hole interaction and load introduction effects for compression-loaded laminates with holes

The effects of hole interaction and load introduction for (+ or - 30/90) sub 8 (s) and (+ or - 45) sub 12 (s) laminates with holes was conducted. A hole interaction region was identified in some specimens, and this region was ineffective for carrying load. The membrane stiffness of a specimen with a hole interaction region is less than the membrane stiffness of a similar specimen without a hole interaction region. A load introduction effect that occurs on the sublaminate level was also observed. This effect can cause a nonuniform load diffusion into the interior of the specimen.

Shuart, M. J.↗
NASA NTRS1984

Investigating compression failure mechanisms in composite laminates with a transparent fiberglass-epoxy birefringent materials

The response and failure of a + or - 45s class laminate was studied by transparent fiberglass epoxy composite birefringent material. The birefringency property allows the laminate stress distribution to be observed during the test and also after the test if permanent residual stresses occur. The location of initial laminate failure and of the subsequent failure propagation are observed through its transparency characteristics. Experimental results are presented.

Shuart, M. J.↗
NASA NTRS1984

Compression failure characteristics of + or - 45-deg-dominated laminates with a circular hole or impact damage

An investigation of the compression failure characteristics of + or - 45-deg-dominated laminates with a circular hole or impact damage was conducted. Graphite-epoxy laminates consisting of all + or - 45-deg plies and of + or - 45-deg and 90-deg plies were evaluated. Inplane shearing between the fibers and matrix (i.e., matrix shearing) was found to be the primary compression failure mechanism for an all + or - 45-deg laminate with a hole. The failure mechanism for the + or 45-deg-dominated laminates with a hole appeared to be a combination of delamination and matrix shearing. The compression failure stresses and strains for both the all + or - 45-deg laminate and the + or - 45-deg-dominated laminates were unaffected by impact damage at an energy level of 5.5 J when compared to results for undamaged control specimens. The failure stresses and strains for all laminates with impact damage at an energy level of 17.0 J or of 34.3 J were significantly lower than the corresponding data for the undamaged control specimens. The failure stresses and strains for these impact-damaged specimens were independent of the percentage of 90-deg plies in the laminate.

Shuart, M. J.↗
NASA NTRS1983

Buckling and failure characteristics of graphite-polyimide shear panels

The buckling and failure characteristics of unstiffened, blade stiffened, and hat stiffened graphite-polyimide shear panels are described. The picture frame shear test is used to obtain shear stress-strain data at room temperature and at 316 deg C. The experimental results are compared with a linear buckling analysis, and the specimen failure modes are described. The effect of the 316 deg C test temperature on panel behavior are discussed.

Shuart, M. J.↗