Engineering Papers⌕ Search

Engineering topics

Shirvan, Koroush

Publications and source records attributed to Shirvan, Koroush.

48 records · Page 3

Assessment of the Subchannel Code CTF for Single- and Two-Phase Flows

As part of the Consortium for Advanced Simulation of Light Water Reactors, the subchannel code CTF is being used for single-phase and two-phase flow analysis under light water reactor operating conditions. Accurate determination of flow distribution, pressure drop, and void content is crucial for predicting margins to thermal crisis and ensuring more efficient plant performance. In preparation for the intended applications, CTF has been validated against data from experimental facilities comprising the General Electric (GE) 3 × 3 bundle, the boiling water reactor full-size fine-mesh bundle tests (BFBTs), the Risø tube, and the pressurized water reactor subchannel and bundle tests (PSBTs). Meanwhile, the licensed, well-recognized subchannel code VIPRE-01 was used to generate a baseline set of simulations for the targeted tests and solution parameters were compared to the CTF results.The flow split verification problem and single-phase GE 3 × 3 results are essentially in perfect agreement between the two codes. For the two-phase GE 3 × 3 cases, flow and quality discrepancies arise in the annular-mist flow regime, yet significant improvement is observed in CTF when void drift and two-phase turbulent mixing enhancement are considered. The BFBT pressure drop benchmark shows close agreement between predicted and measured results in general, although considerable overprediction by CTF is observed at relatively high void locations of the facility. This overestimation tendency is confirmed by the Risø cases. While overall statistics are satisfactory, both BFBT and PSBT bubbly-to-churn flow void contents are markedly overpredicted by CTF.The issues with two-phase closures such as turbulent mixing, interfacial and wall friction, and subcooled boiling heat transfer need to be addressed. As a result, preliminary sensitivity studies are presented herein, but more advanced models and code stability analysis require further investigation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Modeling of Cr 2 O 3 -doped UO 2 as a near-term accident tolerant fuel for LWRs using the BISON code

The near-term Accident Tolerant Fuel (ATF) concepts consist of minor modifications of the standard UO 2 -Zr fuel rod materials to provide enhanced accident tolerance. Uranium dioxide fuel with chromia dopant, developed by AREVA, is of interest in view of its enhanced fission gas retention. The predictive capability of the BISON fuel performance code for chromia-doped UO 2 fuel is assessed through simulation of the Halden IFA-677.1 fuel rod experiment. A sensitivity analysis is conducted to interpret the deviation of code’s predictions from the experimental data. A power ramp test is also modeled with BISON and calculations are compared to the experimental database. Finally, a large-break LOCA (LBLOCA) case is simulated with BISON, leading to an initial assessment of the enhanced safety associated with chromia-doped fuel compared to the standard UO 2 fuel in LWRs

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel performance of chromium-coated zirconium alloy and silicon carbide accident tolerant fuel claddings

The U.S. Department of Energy’s Accident Tolerant Fuel program is focused on extending the time for fuel failure during postulated severe accidents compared to the standard UO2-Zr alloy fuel system. This research investigates the feasibility of two different chromium-coated cladding concepts, one of which is zirconium-alloy based and the other is composite-SiC based. Both claddings had 50µm coatings, deducted from the base layer thicknesses. The claddings were reported on, using the multi- physics fuel performance tool BISON, under steady-state PWR operating conditions as well as two transients: power ramp and a loss-of-coolant accident (LOCA). The chromium-coated claddings showed comparable thermo-mechanical performance to the reference Zircaloy-4 cladding. As chromium is reported to provide an order of magnitude improvement in oxidation resistance, it is expected to be a better alternative in accident scenarios. Simulation results for both concepts call for further experimental investigation as well as modeling of beyond design-basis accidents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modeling physical vapor deposition of energetic materials

Morphology and microstructure of organic explosive films formed using physical vapor deposition (PVD) processes strongly depends on local surface temperature during deposition. Currently, there is no accurate means of quantifying the local surface temperature during PVD processes in the deposition chambers. This study focuses on using a multiphysics computational fluid dynamics tool, STARCCM+, to simulate pentaerythritol tetranitrate (PETN) deposition. The PETN vapor and solid phase were simulated using the volume of fluid method and its deposition in the vacuum chamber on spinning silicon wafers was modeled. The model also included the spinning copper cooling block where the wafers are placed along with the chiller operating with forced convection refrigerant. Implicit time-dependent simulations in two- and three-dimensional were performed to derive insights in the governing physics for PETN thin film formation. PETN is deposited at the rate of 14 nm/s at 142.9 °C on a wafer with an initial temperature of 22 °C. The deposition of PETN on the wafers was calculated at an assumed heat transfer coefficient (HTC) of 400 W/m 2 K. This HTC proved to be the most sensitive parameter in determining the local surface temperature during deposition. Previous experimental work found noticeable microstructural changes with 0.5 mm fused silica wafers in place of silicon during the PETN deposition. This work showed that fused silica slows initial wafer cool down and results in ~10 °C difference for the surface temperature at 500 μm PETN film thickness. It was also found that the deposition surface temperature is insensitive to the cooling power of the copper block due to the copper block's very large heat capacity and thermal conductivity relative to the heat input from the PVD process. Future work should incorporate the addition of local stress during PETN deposition. Lastly, based on simulation results, it is also recommended to investigate the impact of wafer surface energy on the PETN microstructure and morphology formation.

36 MATERIALS SCIENCE↗

Estimation of Core Recovery Time with TRACE

Following the severe accident in Fukushima Daiichi Nuclear Power Plant in Japan, safety related concerns about the zirconium based claddings used in current light water reactors have increased. High corrosion resistance and low neutron absorption cross section make zirconium a suitable cladding material for normal nuclear plant operational conditions. However, for nuclear accident scenarios when safety functions of the plant are lost, Zr claddings undergo exothermic reaction with steam and exacerbate the accident conditions. The exothermic reaction increases the temperature of the cladding and accelerates core melting in severe accident progression. And the generation of explosive hydrogen gas accumulates and challenges the structural integrity. The accident tolerant fuel (ATF) concept is the fuel and cladding system that gives a longer time margin, compared to standard Zr claddings, to cope with the accident when core cooling systems are lost in a nuclear power plant. The ATF cladding should have slower oxidation kinetics and less hydrogen generation than Zr to alleviate consequences of cladding interaction with steam at high temperatures. The maximum time available to mitigate progression of severe accident is an important measure to evaluate benefits of ATF claddings. For this work, the maximum time available to mitigate progression of severe accident is selected as the time at which cladding melting reaction starts. Melting reaction is selected as an upper limit because of the degradation of coolable geometry. Maintaining the coolable geometry is a regulation criteria for both loss of coolant (LOCA) analyses and outside the LOCA analyses. Once the melting of the cladding starts, it exacerbates the deformation of the fuel assembly and hottest rods within the core cannot be cooled by water reflood and results in fuel melting progression. The aim of this work is to evaluate time margin gain of ATF cladding in a severe accident scenario of LOCA without safety injections and station blackout considering oxidation kinetics only. Also it is assumed that safety injections are recovered before melting of the claddings start and the sensitivity of safety injection actuation time on core recovery is analyzed. The core recovery time is the time when makeup water from safety injections quench the fuel rods and halt the progression of the severe accident. This time is estimated by initiating safety injections at different times and observing the hot rod behavior which represents 1/5. of the core in this work. It is considered that core is not recoverable when 20% of the core is damaged.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutronics analysis of fuel-in-fiber concept

One of the consequences of Fukushima was the increase in interest in development of safer, more accident tolerant fuels and claddings. Accident tolerant fuels (ATF) are defined by the Nuclear Regulatory Committee (NRC) as fuels that, in comparison with the standard UO{sub 2}- Zircaloy system, can tolerate loss of active cooling in the core for a considerably longer time period while maintaining or improving the fuel performance during normal operations. One of the ideas being considered is tri-isotropic (TRISO) fuel particles. TRISO fuel pebbles consist of several layers - the outermost being graphite. TRISO pebbles are considered to be accident tolerant, because of their ability to retain fission products at high temperatures. One of the ideas implementing TRISO pebbles is Fully Ceramic Microencapsulated fuel where the pellet is comprised of TRISO pebbles in a matrix. TRISO particles though have a low maximum packing fraction when put in the spherical or cylindrical configuration with the current fabrication techniques (hot and cold press). This leads to considerable increase in enrichment to maintain cycle length for today's Light Water Reactors (LWR). The Fuel-in-Fiber concept, developed by FreeForm-Fiber (FFF), has the advantages of TRISO particles while utilizing a novel additive direct manufacturing technique for rapid fabrication. Fuel-in-Fiber are small fibers made of layers just like TRISO particles but because of their cylindrical nature, they can be packed with a tighter packing fraction than the TRISO particles. The fibers are woven within a SiC matrix and used to replace a typical pellet in a fuel pin. This means that they can easily be placed into LWR's without having to change the assembly or core structures. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nitride Fuel Potential for Power Uprates

This work presents the methodology and current results for design analysis of grid supported pressurized water reactor cores using uranium nitride (UN) fuel in square arrays. Uranium nitride has a higher theoretical density and higher thermal conductivity than uranium oxide, allowing for lower fuel temperatures, longer cycle length and higher power densities with similar enrichment. In order to avoid the UN and high temperature water reaction, silicon carbide cladding has been proposed in place of Zircaloy cladding. The analysis aims at finding the maximum thermal power over a range of bundle geometries (rod diameter and pitch). The same methodology is applied to the design of UO{sub 2} oxide fueled cores to provide a fair comparison of the achievable power rating between the two fuel types. Steady-state limits are considered, including fuel bundle pressure drop, minimum departure from nucleate boiling ratio (MDNBR), fuel temperature, fuel rod vibrations and pin fretting and sliding wear. Transients such as loss of flow and overpower accident will be considered. A steady state analysis was undertaken to determine the maximum achievable power that can be sustained by square array fuel assemblies loaded with nitride and oxide fuels with same or better safety performances as the reference design. Steady-state design limits were applied including MDNBR, fuel bundle pressure drop, fuel temperature, cumulative sliding and fretting wear. The major conclusions of this study are as follows: 1) It is possible to achieve significant power increase for UN and UO{sub 2} compared to the reference core power output of 3400 MWth with smaller but more numerous rods and higher pitch over diameter ratios. A power uprate of 25% can be reached according to the VIPRE-MATLAB interface for full core analysis with the same number of spacer grids, and 32% according to the new MATLAB script for single hot channel analysis, with five more spacer grids. For this latter core, a higher enrichment would be required. 2) The nitride fuel temperature constraint from dissociation doesn't influence steady state performances as other design constraints such as MDNBR and pressure loss are more restrictive. The oxide fuel temperature constraint from fission gas release is reached in part of the study domain, but not in the region that allows for possible uprates. 3) As a result, the thermal hydraulic performance of UN and UO{sub 2} are similar. Differences in possible power uprates will arise from fretting and sliding wear. Wear depends of the time spent by the fuel in the core, which depends on burnup and heavy metal inventory. UN being denser, it can allow for power uprates or increased cycle length. There is a trade off between power uprates and cycle length with regards to fuel pin wear. Reducing fuel pin wear by reducing cycle length can allow for higher thermal power. This affects the plants' economics as well. This work will be completed by a transient analysis using CASMO4E, SIMULATE3 and SIMULATE3k to model the neutronics of a nitride fueled core. The transient performances will be used to determine the maximum power uprates while performing as well or better during transients as the reference design. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Self-Sustaining Thorium Boiling Water Reactors

The primary objectives of this project are to: Perform a pre-conceptual design of a core for an alternative to the Hitachi proposed fuel-self- sustaining RBWR-AC, to be referred to as a RBWR-Th. The use of thorium fuel is expected to assure negative void coefficient of reactivity (versus positive of the RBWR-AC) and improve reactor safety; Perform a pre-conceptual design of an alternative core to the Hitachi proposed LWR TRU transmuting RBWR-TB2, to be referred to as the RBWR-TR. In addition to improved safety, use of thorium for the fertile fuel is expected to improve the TRU transmutation effectiveness; Compare the RBWR-Th and RBWR-TR performance against that of the Hitachi RBWR core designs and sodium cooled fast reactor counterparts - the ARR and ABR; and, Perform a viability assessment of the thorium-based RBWR design concepts to be identified along with their associated fuel cycle, a technology gap analysis, and a technology development roadmap. A description of the work performed and of the results obtained is provided in this Overview Report and, in more detail, in the Attachments. The major findings of the study are summarized.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗