Engineering Papers⌕ Search

Engineering topics

Shin, S. J.

Publications and source records attributed to Shin, S. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of growth rate and dynamic substrate tilt on properties of Au-Ta alloy films deposited by high-power impulse magnetron sputtering

Gold-tantalum (Au—Ta) alloys are promising for next-generation hohlraums for magnetically-assisted indirect-drive inertial confinement fusion. Hohlraum fabrication involves sputter deposition of ultrathick coatings on sphero-cylindrical substrates. The control of physical properties of such coatings remains a challenge. Here, in this work, we systematically study effects of the growth rate and dynamic substrate tilt on properties of AuTa 4 films deposited onto rotating planar substrates mounted at different tilt angles to mimic different regions of the sphero-cylindrical surface of a hohlraum. We use high-power impulse magnetron sputtering (HiPIMS) in the constant charge per pulse mode with a pulse duration of 100 μs, a charge per pulse of 190 μC, a peak target current of about 3 A, and the pulse frequency varied in the range of 400–1400 Hz. The Langmuir probe, mass-resolved ion energy spectrometry, and optical emission spectroscopy are used to monitor plasma discharge characteristics in order to isolate and study effects of the growth rate. The deposition rate and the ballistics and energetics of depositing species are estimated by Monte Carlo simulations. Results show that the film microstructure, crystallographic phase, residual stress, and electrical resistivity strongly depend on both the deposition rate and substrate tilt, highlighting their critical role in tailoring properties of Au—Ta films during hohlraum fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Boron carbide films with reduced nodular defect density deposited by full-face erosion radio-frequency magnetron sputtering

Boron carbide coatings deposited by sputtering with conventional planar magnetrons exhibit nodular growth defects. Here, we demonstrate that the density of nodular defects in B 4 C films can be greatly reduced by using a full-face-erosion magnetron source that achieves a more uniform target erosion by sweeping the confining magnetic field over the target surface. Here, we systematically study properties of B 4 C films deposited on substrates with different tilt angles and demonstrate deposition of ultrathick films with compressive residual stress below 200MPa.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Magnetron sputter deposition of boron carbide in Ne and Ar plasmas

Conventional magnetron sputter deposition of B 4 C uses Ar as the working gas. In this report we explore the magnetron sputter deposition of B 4 C with a Ne plasma, which is expected to exhibit larger sputtering yields than Ar. We study properties of films deposited with different substrate tilt angles with the magnetron source operated in either direct-current (DC) or radio-frequency (RF) mode in an Ar or Ne plasma. Results show that the B 4 C film properties are determined by a combination of sputtering ballistics and effects of the working gas on the plasma discharge and gas phase scattering of depositing species flux. At constant discharge power, deposition rates for Ar and Ne plasmas are similar, which is attributed to balancing effects of a higher ballistic sputtering yield of Ne and lower ion flux to the target. Both depositing B and C neutral species and bombarding ions have higher energies for the case of Ne plasmas. Films deposited with the RF-driven Ne plasma exhibit a uniform non-columnar structure, lowest oxygen impurity content, and highest mass density and mechanical properties at a cost of Ne incorporation and larger compressive residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Observations and properties of the first laboratory fusion experiment to exceed a target gain of unity

An indirect-drive inertial fusion experiment on the National Ignition Facility was driven using 2.05 MJ of laser light at a wavelength of 351 nm and produced 3.1±0.16 MJ of total fusion yield, producing a target gain G=1.5±0.1 exceeding unity for the first time in a laboratory experiment [Phys. Rev. E 109, 025204 (2024)]. Herein we describe the experimental evidence for the increased drive on the capsule using additional laser energy and control over known degradation mechanisms, which are critical to achieving high performance. Further, improved fuel compression relative to previous megajoule-yield experiments is observed. Novel signatures of the ignition and burn propagation to high yield can now be studied in the laboratory for the first time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Development of New Magnetron Sputter Deposition Processes for Laser Target Fabrication

Magnetron sputter deposition is an enabling technology for laser target fabrication. Solutions are readily available for the deposition of most sub-micron-thick elemental films on planar substrates. However, major challenges still remain for the development of robust deposition processes in regimes of ultrathick (over ~10 μm) coatings and nonplanar substrates. These challenging deposition regimes are directly relevant to laser target applications, including both sphero-cylindrical hohlraums and spherical ablators for inertial confinement fusion (ICF) targets. Understanding underlying physical mechanisms for a specific material system is crucial for process development, given the overall complexity of the deposition process, its nonlinear dependence on deposition parameters, and a very large process space, often precluding conventional process optimization approaches. Here, we describe our approach to developing new deposition processes and give practical advice with examples of new results from our ongoing studies of glassy boron carbide ceramics for next-generation ICF ablators and nonequilibrium gold-tantalum alloys for hohlraums for magnetized ICF schemes. Emphasis is given to two major challenges of ultrathick coatings related to achieving process stability and reducing residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Radio-frequency magnetron sputter deposition of ultrathick boron carbide films

The deposition of thick B 4 C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B 4 C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ~0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B 4 C films is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tungsten doped diamond shells for record neutron yield inertial confinement fusion experiments at the National Ignition Facility

We report on fabrication and characterization of layered, tungsten doped, spherical about 2 mm diameter microcrystalline diamond ablator shells for inertial confinement fusion (ICF) experiments at the National Ignition Facility. As previously reported, diamond ICF ablator shells can be fabricated by chemical vapor deposition (CVD) on solid spherical silicon mandrels using an ellipsoidal microwave plasma reactor. In the present work, we further developed these ablator shells by embedding a W -doped diamond layer sandwiched between two undoped diamond regions. W incorporation in diamond was achieved by adding tungsten hexacarbonyl to the CH 4 /H 2 CVD feed gas. We observe that the W doping concentration decreases with increasing deposition rate which, in turn, is controlled by adjusting the total gas pressure. Cross sectional microstructural analysis reveals sharp interfaces between doped and undoped regions of the diamond shell and uniform W distribution with concentrations up to about 0.3 at.%. At higher W concentrations (>0.3 at.%) formation of tungsten carbide precipitates is observed. Using a 3-shock 1.6 MJ laser pulse, the targets described in this work produced the first laser driven implosion to break the 1 × 10 16 neutron yield barrier, followed by experiments (described in future publications) with similar targets and slightly more laser energy producing yields as high as 4 × 10 17 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Combinatorial sputter deposition of ultrathick Au-Bi alloy films

We report gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ~20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au 2 Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ~30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reactive co-sputtering of ternary Au–Ta–O films with tunable electrical resistivity

Heavy-metal-based films with high electrical resistivity are needed for hohlraums for magnetically-assisted inertial confinement fusion. Here, we study ternary Au-Ta-O films deposited by reactive direct-current magnetron co-sputtering from elemental Au and Ta targets in an oxygen containing atmosphere. By varying O content, the electrical resistivity of films can be tuned in a wide range of ~ 100 - 40,000 μΩ cm. With increasing O content, a drastic increase in resistivity occurs at ~ 45 at.% of O, separating regimes with two different dominant conduction mechanisms attributed to metallic conduction through the Au-Ta alloy matrix (for ≲ 45 at.% of O) and tunneling across insulating Ta 2 O 5 layers separating conducting islands (for ≳ 45 at.% of O). Post-deposition annealing at 300 °C leads to the segregation of Au into ~ 50-nm islands, sharply decreasing the resistivity for films with ≳ 45 at.% of O but not for the metal-like films with lower O content.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Experimental achievement and signatures of ignition at the National Ignition Facility

An inertial fusion implosion on the National Ignition Facility, conducted on August 8, 2021 (N210808), recently produced more than a megajoule of fusion yield and passed Lawson's criterion for ignition [Phys. Rev. Lett. 129, 075001 (2022)]. Here we describe the experimental improvements that enabled N210808 and present the first experimental measurements from an igniting plasma in the laboratory. Ignition metrics like the product of hot-spot energy and pressure squared, in the absence of self-heating, increased by ~ 35%, leading to record values and an enhancement from previous experiments in the hot-spot energy (~ 3×), pressure (~ 2×), and mass (~ 2×). These results are consistent with self-heating dominating other power balance terms. The burn rate increases by an order of magnitude after peak compression, and the hot-spot conditions show clear evidence for burn propagation into the dense fuel surrounding the hot spot. These novel dynamics and thermodynamic properties have never been observed on prior inertial fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates

Sputter deposition of gold-tantalum alloy coatings is a key process for manufacturing hohlraums for magnetically-assisted inertial confinement fusion implosions. In this report we describe direct current magnetron sputter deposition of ~ 10 - μ~ 10 - μm-thick films of Au-80 at.% Ta onto rotating sphero-cylindrical hohlraum and planar Si witness substrates. Emphasis is given to how film microstructure and properties are affected by main deposition parameters, including argon working gas pressure, substrate bias, and the source composition (a single alloyed target compared to co-sputtering from two elemental targets). Experimental findings are correlated with distributions of landing energies and incident angles of depositing species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Deposition conditions characterized by low energetics of depositing species favor the formation of a β-Ta-like phase. Implications of these results to hohlraum fabrication are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of substrate temperature on sputter-deposited boron carbide films

Sputter deposition of B4C films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of B4C films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of 100-510°C. Results show that all films are amorphous stoichiometric B4C, with low O content of ~1 at. %. Films deposited onto substrates at 100°C exhibit high compressive residual stress and decreased mechanical properties. Therefore, for elevated substrate temperatures in the range of 180-510°C, film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of ~185-250°C is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Gold-tantalum alloy films deposited by high-density-plasma magnetron sputtering

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. Here, we systematically study the effects of substrate tilt (0°–80°) and negative substrate bias (0–100 V) on properties of ≲3-μm-thick films deposited by high-power impulse magnetron sputtering (HiPIMS) from a Au–Ta alloy target (with 80 at. % of Ta). Results reveal that, for all the substrate bias values studied, an increase in substrate tilt leads to a monotonic decrease in film thickness, density, residual compressive stress, and electrical conductivity. Larger substrate bias favors the formation of a body-centered cubic phase, with films exhibiting lower column tilt and higher density, electrical conductivity, and residual compressive stress. Furthermore, these changes are attributed to metal atom ionization effects, based on the lack of correlation with distributions of landing energies and incident angles of depositing species as calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. By varying substrate tilt and bias in HiPIMS deposition, properties of Au–Ta alloy films can be controlled in a very wide range, including residual stress from –2 to +0.5 GPa, density from 12 to 17 g/cm 3 , and the electrical resistivity from 50 to 4500 μΩ cm, enabling optimum deposition conditions to be selected for specific applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Oblique angle deposition of boron carbide films by magnetron sputtering

Many applications of boron carbide (B4C) films entail deposition on non-planar substrates, necessitating a better understanding of oblique angle deposition phenomena. Here, we systematically study the effect of substrate tilt on properties of B 4 C films with thicknesses up to 10 μm deposited by direct current magnetron sputtering. Results show that all films are amorphous and columnar with an average column width of ~100 nm, independent of substrate tilt. Column tilt angles are limited to ~20° even for substrate tilt of 80°. Film density, residual stress, and the refractive index weakly (within ≲20%) depend on substrate tilt. Furthermore, oxygen impurities bond preferentially with carbon atoms in inter-columnar regions. Substrate tilt has a major effect on mechanical properties that decrease by ~50%, suggesting weak interconnection between nano-columns. Implications of these observations for the deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sputtered Au–Ta films with tunable electrical resistivity

Gold–tantalum alloy films are attractive for hohlraums used in indirect drive magnetized inertial confinement fusion. A high electrical resistivity of over ~100 µΩ cm at cryogenic temperatures is an essential requirement for allowing an externally imposed pulsed magnetic field to soak through a hohlraum and magnetize the fusion fuel. In this work, we systematically study properties of Au–Ta alloy films in the entire compositional range from pure Au to pure Ta with thicknesses up to 30 µm. These films are made by direct current magnetron co-sputtering on planar substrates. Films are characterized by a combination of high-energy ion scattering, x-ray diffraction, electron microscopy, nanoindentation, and electrical transport measurements. Results show that an alloy with ~80 at.% of Ta forms a metallic glass exhibiting a maximum electrical resistivity of ~300 µΩ cm with a weak temperature dependence in the range of 5–400 K. The deposition of a film with ~80 at.% of Ta onto a sphero-cylindrical substrate for hohlraum fabrication is also demonstrated.

36 MATERIALS SCIENCE↗