Engineering topics

Shen, Tengming

Publications and source records attributed to Shen, Tengming.

7 records

DOE OSTI2026

The High Rigidity Spectrometer at the FRIB: Magnet Development Status

This paper presents the 2025 progress of the High Rigidity Spectrometer (HRS) project at the Facility for Rare Isotope Beams (FRIB). We report on the construction and testing of the first-article HRS-High Transmission BeamLine (HTBL) magnets. An HTBL dipole magnet has successfully completed cold testing, achieving full magnetic performance without quenching, and is now ready for field mapping at FRIBs offline test bench. HTBL quadrupole triplet coils have been fabricated and tested, with all coils reaching their design currents, some following initial training quenches. Furthermore, the preliminary design of the large-scale, large-aperture SPectrometer Section (SPS) magnets has progressed to determine the baseline of the downstream HRS-SPS subproject in 2025. This includes the introduction of novel magnet designs, such as the sweeper dipole magnet, the sector dipole magnet, and iron-free coil-dominated quadrupole magnets, representing a significant scale breakthrough and a first for FRIB.

Choi, Yoonhyuck↗

DOE OSTI2025

A round bobbin critical current measurement and thermal runaway simulation of REBCO coated conductors

A round bobbin test has been widely used to measure critical current Ic of practical superconductors including Nb–Ti, Nb3Sn, and Bi-2212 round strands at 4.2 K and in high magnetic fields but rarely used for rare earth-barium-copper-oxide (REBCO) coated conductor tapes. Here, we applies this method to REBCO tapes and test their Ic at 77 K, self-field, and 4.2 K with a magnetic field of 14 T applied parallel to the tape. The sample carries very high current densities; it is 1.3 m long and has a dense array of voltage taps that allows probing localized thermal runaways and correlation with Ic variations along the length. At 77 K, the Ic values of all sections were measured and found to be rather uniform. However, at 4.2 K, we found that a 3 cm section has 90% of the overall voltage drop and it went into thermal runaways upon further increasing current. Thus, at 4.2 K, we were prevented by localized thermal runaways and unable to determine Ic of most of the REBCO conductor sections; this behavior is different from Bi-2212 and Bi-2223 for which Ic of all turns of a round barrel sample can be determined. We simulate REBCO tapes during current ramping to a thermal runaway and analyze impacts of various factors including cooling, conductor n-values, and thickness of stabilizer on the thermal runaway current Iq. The combined experiments and simulations identify n-value as a crucial factor that leads to the observed differences between Bi-2212 and REBCO. Together with cooling and the standard deviation of Ic variations along the length, the n-value determines whether Iq is above or below the average Ic of a long piece of conductor and their ratio Iq/Ic,ave, greatly affecting quench detection and thermal runaway prevention strategies of Bi-2212 and REBCO magnets.

Mosat, Marek↗

DOE OSTI2025

Irradiation-induced gas production in REBCO-based magnet materials used for future compact fusion reactors

Nuclear fusion is an enticing alternative to current sources of energy, with multilayered Rare-Earth Barium Copper Oxide (REBCO) coated conductors deemed pivotal in the race toward fully realized, commercially viable, and magnetic confinement fusion reactors. In this study, we simulated the ion spectrum expected to evolve from REBCO's nickel-based Hastelloy C-276 substrate and copper stabilizer in an affordable robust compact-like reactor. We then emulated this gas production through helium implantation to investigate changes in materials and superconducting properties. Our results revealed that the substrate and stabilizer are capable of producing protons energetic enough to recoil throughout the tape thickness in appreciable doses, and alphas energetic enough to deposit 7.54 × 1014 ions/cm2 or 50.1 helium appm in the superconducting layer over a 30-year reactor lifetime. The superconducting layer of SuperPower® tapes exhibited at least double the swelling rate of the other major layers, and both SuperPower and Fujikura Ltd. tapes displayed microstructural changes in the REBCO layer not observed in isotropic metals. For the estimated lifetime fluence, the Fujikura tapes showed a ∼1 K reduction in critical temperature and a 32% degradation in critical current for compact reactor-relevant conditions (16 T, 20 K). Nuclear transmutation, low-temperature solder implantations, gas-ion evolution, the influence of gas production on vortex dynamics, and other related considerations are also discussed.

Reis, Chris↗

DOE OSTI2024

FRIB Beam Power Ramp-up: Status and Plans

After project completion on scope, on cost, and ahead of schedule, the Facility for Rare Isotope Beams began operations for scientific users in May of 2022. The ramp-up to a beam power of 400 kW is planned over a six-year period; 1 kW was delivered for initial user runs from in 2022, and 5 kW was delivered as of February 2023. Test runs with 10 kW 36Ar and 48Ca beams were conducted in July 2023. Upgrade plans include doubling the primary-beam energy to 400 MeV/nucleon for enhanced discovery potential (¿FRIB 400¿). This talk reports on the strategic plans towards high power operations emphasizing challenges and resolutions in beam-interception devices and targetry systems, radiation protection and controls, and legacy system renovation and integration.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Flux Creep in a Bi-2212 Rutherford Cable for Particle Accelerator Applications

Bi-2212 superconducting cables are being considered for use in the high field magnets needed for the next generation of particle accelerators. Magnetization in these cables and the decay of that magnetization lead to field error and field-error drift, respectively, which need to be compensated. To study this, a segment of the winding pack was extracted from a racetrack coil made from Bi-2212 Rutherford cable. Using a Hall probe measurement technique, we measured the response of the cable's magnetization and its magnetization decay to changes in the applied magnetic field. The effect of adjustments to the cycling of the magnetic field was studied, intended to simulate the preinjection cycles of an accelerator magnet. Three M vs. H loops were constructed by sweeping the magnetic field applied to the sample from 0 to 2.5 T, then to a preinjection field 'x' (where x = 0, 0.25, 0.75 T), and finally up to 1 T. The applied field was then held at 1 T for 1500 s, and the magnetization decay was measured. Finally, the decay was found to vary from 8% to 14% after 1500 s, depending on the preinjection field cycle.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Mechanical and Thermal Analysis of an HTS Superconducting Magnet for an Achromatic Gantry for Proton Therapy

The mechanical and thermal analysis of the superconducting magnets, forming an innovative fixed-field bending section for use in a proton therapy gantry, is presented here. In this work, the design concept has a large momentum acceptance, covering the full proton energy range of 70 to 220 MeV with fixed field in the superconducting magnets, and uses a simple magnet geometry based on double-pancake high temperature superconductor coils. The main planned steps for the assembly and fabrication of the magnets are discussed. The mechanical analyses of the magnet, with emphasis on the stress state of the conductor during the powering of the magnet, is here described. The thermal analysis investigating the adequacy of the copper structure surrounding the conductor to extract the heat deposited in the conductor during powering is also discussed in detail.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Stabilization and control of persistent current magnets using variable inductance

Ultra-stable, tunable magnetic fields are desirable for a wide range of applications in medical imaging, electron microscopy, quantum science, and atomic physics. Superconducting magnets operated in persistent current mode, with device current flowing in a closed superconducting loop disconnected from a power source, are a common approach for applications with the most stringent requirements on temporal field stability. In this work, we present a method for active control of this persistent current by means of dynamic inductance change within the superconducting circuit. For a first realization of this general technique, we consider a variable superconducting inductor placed in series with the main magnet. The inductor acts as a dynamic flux storage device capable of transferring flux to or from the main magnet through inductance change. This allows for fine and fast adjustments of the persistent current without the use of thermal switches that limit the speed and accuracy of many present-day methods. With first experiments employing this technique, we demonstrate stabilization of a 1.95 T Nb–Ti round lens for electron microscopy against decay resulting from residual losses in the superconducting circuit, and more generally show flexibility for precise control over the magnitude and waveform of the persistent current.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗