Engineering topics

Shen, D. H.

Publications and source records attributed to Shen, D. H..

30 records · Page 2

NASA NTRS1990

Capacity decline of ambient temperature secondary Li-TiS2 cells

The main objective of the study described was to identify the causes responsible for the capacity losses observed during cycling of secondary Li-TiS2 cells. Experimental Li-TiS2 cells were fabricated and tested for their cycle life performance. The open circuit voltage of the cells was monitored during the rest period between the charging and discharging. The polarization at the Li and TiS2 electrodes was also monitored during cycling. Cycled cells were disassembled and the cathodes were analyzed by various analytical techniques. The results of the study indicate that the observed capacity loss is almost entirely due to the increased polarization of the TiS2 electrode with cycling. The electrolyte was found to degrade during cycling and the degradation products were found to deposit at the TiS2 electrode, which probably lead to the higher polarization.

Subbarao, S.↗

NASA NTRS1989

Advances in ambient temperature secondary lithium cells

The goal is to develop secondary lithium cells with a 100 Wh/kg specific energy capable of 1000 cycles at 50 percent DOD. The approach towards meeting this goal initially focused on several basic issues related to the cell chemistry, selection of cathode materials and electrolytes and component development. The performance potential of Li-TiS2, Li-MoS3, Li-V6O13 and Li-NbSe3 electrochemical systems was examined. Among these four, the Li-TiS2 system was found to be the most promising system in terms of achievable specific energy and cycle life. Major advancements to date in the development of Li-TiS2 cells are in the areas of cathode processing technology, mixed solvent electrolytes, and cell assembly. A summary is given of these advances.

Subbarao, S.↗

NASA NTRS1989

Low temperature testing of Li-SOCl2 cells

The performance and safety characteristics Li-SOCl2 cells were evaluated at -40 C. Tests were conducted on cells of several defferent designs to determine the influence of cell design on performance and safety. The cells exhibited low operating voltages, poor voltage regulation, and low capacity at -40 C. The performance of the cells was found to be critically dependent on the cell design. No safety problems were observed during discharge to 2.0 V under constant current and constant load operating conditions. Cells subjected to prolonged periods of continuous drain at constant-load did not vent/rupture upon warm-up. Cells subjected to prolonged reversal were found to be potentially hazardous. Microcalorimetry and electrochemical impedance spectroscopy studies performed on the cells suggested that those containing a catalyst may exhibit poor shelf life.

Subbarao, S.↗

NASA NTRS1989

Advances in ambient temperature secondary lithium cells

The Jet Propulsion Laboratory is involved in a Research and Development program sponsored by NASA/OAST on the development of ambient temperature secondary lithium cells for future space applications. Some of the projected applications are planetary spacecraft, planetary rovers, and astronaut equipment. The main objective is to develop secondary lithium cells with greater than 100 Wh/kg specific energy while delivering 1000 cycles at 50 percent Depth of Discharge (DOD). To realize these ambitious goals, the work was initially focused on several important basic issues related to the cell chemistry, selection of cathode materials and electrolytes, and component development. The performance potential of Li-TiS2, Li-MoS3, Li-V6O13 and Li-NbSe3 electrochemical systems was examined. Among these four, the Li-TiS2 system was found to be the most promising system in terms of realizable specific energy and cycle life. Some of the major advancements made so far in the development of Li-TiS2 cells are in the areas of cathode processing technology, mixed solvent electrolytes, and cell assembly. Methods were developed for the fabrication of large size high performance TiS2 cathodes. Among the various electrolytes examined, 1.5M LiAsF6/EC + 2-MeTHF mixed solvent electrolyte was found to be more stable towards lithium. Experimental cells activated with this electrolyte exhibited more than 300 cycles at 100 percent Depth of Discharge. Work is in progress in other areas such as selection of lithium alloys as candidate anode materials, optimization of cell design, and development of 5 Ah cells. The advances made at the Jet Propulsion Laboratory on the development of secondary lithium cells are summarized.

Subbarao, S.↗

NASA NTRS1988

Development of ambient temperature secondary lithium cells

JPL is developing ambient temperature secondary lithium cells for future spacecraft applications. Prior studies on experimental laboratory type Li-TiS2 cells yielded promising results in terms of cycle life and rate capability. To further assess the performance of this cell, 5 Ah engineering model cells were developed. Initially baseline cells were designed and fabricated. Each cell had 15 cathodes and 16 anodes and the ratio of anode to cathode capacity is 6:1. A solution of 1.5 molar LiAsF6 in 2Me-THF was used as the electrolyte. Cells were evaluated for their cycle life at C/1 and C/5 discharge rates and 100 percent depth of discharge. The cells were cycled between voltage limits 1.7 and 2.8 volts. The rate of charge in all cases is C/10. The results obtained indicate that cells can operate at C/10 to C/2 discharge rates and have an initial energy density of 70 Wh/kg. Cells delivered more than 100 cycles at C/2 discharge rate. The details of cell design, the test program, and the results obtained are described.

Subbarao, S.↗

NASA NTRS1988

Low temperature safety of lithium-thionyl chloride cells

The use of lithium thionyl chloride cells for low-temperature applications is presently restricted because of their unsafe behavior. An attempt is made in the present investigation to identify the safe/unsafe low temperature operating conditions and to understand the low temperature cell chemistry responsible for the unsafe behavior. Cells subjected to extended reversal at low rate and -40 C were found to explode upon warm-up. Lithium was found to deposit on the carbon cathodes during reversal. Warming up to room temperature may be accelerating the lithium corrosion in the electrolyte. This may be one of the reasons for the cell thermal runaway.

Subbarao, S.↗

NASA NTRS1988

Capacity decline of ambient temperature secondary lithium battery

The use of ambient temperature secondary lithium cells is limited primarily because of the poor cycle life performance. Much of the cell capacity is irreversibly lost upon cycling. Studies have been undertaken to understand the problem of capacity decline. Experimental Li-TiS2 cells were fabricated and tested for their cycle life performance. Cells were disassembled at different stages of cycle life, and cell active components were analyzed by various analytical techniques. The results of this study indicate that all the cell's active components/materials are undergoing degradation. Details of the experiments carried out and the results obtained are described.

Shen, D. H.↗

NASA NTRS1988

Evaluation of mixed solvent electrolytes for ambient temperature secondary lithium cells

The ethylene carbonate/2-methyltetrahydrofuran (EC/2-MeTHF) mixed-solvent electrolyte has been experimentally found to possess many desirable electrolyte characteristics for ambient-temperature secondary Li-TiS2 cell applications. As many as 300 cycles have been demonstrated, and a cycling efficiency figure-of-merit of 38.5 percent, for 10-percent EC/90-percent MeTHF mixed-solvent electrolyte in experimental Li-TiS2 cells. The improved performance of this electrolyte is attributable to the formation of a beneficial passivating film on the Li electrode by interaction with the EC.

Shen, D. H.↗

NASA NTRS1987

Development of ambient temperature secondary lithium cells

Subbarao, S.↗

NASA NTRS1986

Examination of design options for 35 Ah ambient temperature Li-TiS sub 2 cells

The Jet Propulsion Laboratory is actively engaged in the development of ambient temperature rechargable lithium cells for future NASA geosynchronous Earth orbit (GEO) missions. To achieve these ambitious goals, Li-TiS2, Li-MoS3, and Li-V6O13 systems were examined in detail. Among these three, the Li-TiS2 system has shown the longest life cycle and highest rate capability. Experimental Li-TiS2 batteries (10.5 V, 0.4 Ah) developed in-house have completed eight simulated and accelerated GEO seasons successfully. Inview of the encouraging results, the design options were examined for a scaled-up Li-TiS2 cell. It is hoped that the results of these studies will provide guidelines for prioritizing the research efforts and guiding the selection of optimized materials. Designs for 35 Ah Li-TiS2 cell were examined because present day geosynchronous satellites are powered by batteries of 35 Ah capacity. A computer program was developed to evaluate the influence of various design parameters on the specific energy and the rate capability of the cells.

Shen, D. H.↗

NASA NTRS1986

The design analysis of a rechargeable lithium cell for space applications

Ambient temperature rechargeable lithium batteries are needed by NASA for advanced space power applications for future missions. Specific energies of not less than 100 Wh/kg and long cycle life are critical performance goals. A design analysis of a 35 Ah Li-TiS2 cell was carried out using literature and experimental data to identify key design parameters governing specific energy. It is found that high specific energies are achievable in prismatic cells, especially with the use of advanced hardware materials. There is a serious need for a greatly expanded engineering database in order to enable more quantitative design analysis.

Subba Rao, S.↗

NASA NTRS1983

Elastomeric binders for electrodes

The poor mechanical integrity of the cathode represents an important problem which affects the performance of ambient temperature secondary lithium cells. Repeated charge of a TiS2 cathode may give rise to stresses which disturb the electrode structure and can contribute to capacity loss. An investigation indicates that the use of an inelastic binder material, such as Teflon, aggravates the problem, and can lead to electrode disruption and poor TiS2 particle-particle contact. The feasibility of a use of elastomers as TiS2 binder materials has, therefore, been explored. It was found that elastomeric binders provide an effective approach for simplifying rechargeable cathode fabrication. A pronounced improvement in the mechanical integrity of the cathode structure contributes to a prolonged cycle life.

Yen, S. P. S.↗