Engineering Papers⌕ Search

Engineering topics

Shen, Chao

Publications and source records attributed to Shen, Chao.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Epitaxial Thin Film Growth on Recycled SrTiO 3 Substrates Toward Sustainable Processing of Complex Oxides

Complex oxide thin films cover a range of physical properties and multifunctionalities that are critical for logic, memory, and optical devices. Typically, the high‐quality epitaxial growth of these complex oxide thin films requires single crystalline oxide substrates such as SrTiO 3 (STO), MgO, LaAlO 3 , a‐Al 2 O 3, and many others. Recent successes in transferring these complex oxides as free‐standing films not only offer great opportunities in integrating complex oxides on other devices, but also present enormous opportunities in recycling the deposited substrates after transfer for cost‐effective and sustainable processing of complex oxide thin films. In this work, the surface modification effects introduced on the recycled STO are investigated, and their impacts on the microstructure and properties of subsequently grown epitaxial oxide thin films are assessed and compared with those grown on the pristine substrates. Detailed analyses using high‐resolution scanning transmission electron microscopy and geometric phase analysis demonstrate distinct strain states on the surfaces of the recycled STO versus the pristine substrates, suggesting a pre‐strain state in the recycled STO substrates due to the previous deposition layer. These findings offer opportunities in growing highly mismatched oxide films on the recycled STO substrates with enhanced physical properties. Specifically, yttrium iron garnet (Y 3 Fe 5 O 12 ) films grown on recycled STO present different ferromagnetic responses compared to that on the pristine substrates, underscoring the effects of surface modification. The study demonstrates the feasibility of reuse and redeposition using recycled substrates. Via careful handling and preparation, high‐quality epitaxial thin films can be grown on recycled substrates with comparable or even better structural and physical properties toward sustainable process of complex oxide devices.

pre-strained STO surfaces↗
DOE OSTI2024

High‐Temperature Mechanical Behavior of Single‐Crystal FeCrAl Alloy Under In Situ Micropillar Compression

FeCrAl cladding is one of the candidate materials for the near‐term accident‐tolerant fuel technologies under development. Research on high‐temperature mechanical behaviors of single‐crystal FeCrAl alloy is rather limited. Previous studies have reported the mechanical property of low‐index orientation in single‐crystal FeCrAl alloy at room temperature. However, the critical resolved shear stress to activate slip systems can be orientation and temperature dependent. Here, single‐crystal grains in a coarse‐grained FeCrAl alloy with different crystallographic orientations are selected to preferentially activate {110}<111> slip systems or {112}<111> slip systems. Micropillars are fabricated in the selected single‐crystal grains and tested at elevated temperatures in situ in a scanning electron microscope. The critical resolved shear stresses of {110}<111> slip systems and {112}<111> slip systems are determined at various temperatures. The critical resolved shear stress shows a temperature dependence and orientation independence. This study provides important insight for understanding the deformation mechanisms of FeCrAl alloys at elevated temperatures.

Sun, Tianyi↗
DOE OSTI2024

Additive manufacturing of an ultrastrong, deformable Al alloy with nanoscale intermetallics

Abstract Light-weight, high-strength, aluminum (Al) alloys have widespread industrial applications. However, most commercially available high-strength Al alloys, like AA 7075, are not suitable for additive manufacturing due to their high susceptibility to solidification cracking. In this work, a custom Al alloy Al 92 Ti 2 Fe 2 Co 2 Ni 2 is fabricated by selective laser melting. Heterogeneous nanoscale medium-entropy intermetallic lamella form in the as-printed Al alloy. Macroscale compression tests reveal a combination of high strength, over 700 MPa, and prominent plastic deformability. Micropillar compression tests display significant back stress in all regions, and certain regions have flow stresses exceeding 900 MPa. Post-deformation analyses reveal that, in addition to abundant dislocation activities in Al matrix, complex dislocation structures and stacking faults form in monoclinic Al 9 Co 2 type brittle intermetallics. This study shows that proper introduction of heterogeneous microstructures and nanoscale medium entropy intermetallics offer an alternative solution to the design of ultrastrong, deformable Al alloys via additive manufacturing.

Science & Technology - Other Topics↗
DOE OSTI2024

ZnO-Au Hybrid Metamaterial Thin Films with Tunable Optical Properties

ZnO-Au nanocomposite thin films have been previously reported as hybrid metamaterials with unique optical properties such as plasmonic resonance properties and hyperbolic behaviors. In this study, Au composition in the ZnO-Au nanocomposites has been effectively tuned by target composition variation and thus resulted in microstructure and optical property tuning. Specifically, all the ZnO-Au nanocomposite thin films grown through the pulsed laser deposition (PLD) method show obvious vertically aligned nanocomposite (VAN) structure with the Au nanopillars embedded in the ZnO matrix. Moreover, the average diameter of Au nanopillars increases as Au concentration increases, which also leads to the redshifts in the surface plasmon resonance (SPR) wavelength and changes in the hyperbolic behaviors of the films. As a whole, this work discusses how strain-driven tuning of optical properties and microstructure resulted through a novel Au concentration variation approach which has not been previously attempted in the ZnO-Au thin film system. These highly ordered films present great promise in the areas of sensing, waveguides, and nanophotonics to name a few.

Bhatt, Nirali A.↗
DOE OSTI2023

In Situ Study on Cu-to-Cu Thermal Compression Bonding

Cu-to-Cu thermal compression bonding (TCB) has emerged as a promising solution for ultrafine pitch packaging in 3D integrated circuit technologies. Despite the progress made by conventional Cu-to-Cu TCB methods in achieving good mechanical strength of the Cu bonds, the bonding processes generally require high temperature and high pressure, which may degrade the performance and reliability of the device. Therefore, it is imperative to investigate the processing parameters to understand the bonding mechanism and achieve effective TCB at a low temperature and low pressure. Here, we developed an in situ TCB technique inside a scanning electron microscope. The in situ TCB method enables a real-time observation of bonding development, which provides critical insights into how the texture and microstructure of Cu bumps may influence the creep and surface diffusion during the bonding process. This work features a strategy to advance our understanding of the bonding mechanisms and provides insight into tailoring the microstructure of Cu for bonding at a low temperature and low pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Constructing uniform oxygen defect engineering on primary particle level for high-stability lithium-rich cathode materials

Lithium-rich layered cathode materials are considered to be research focus of cathode candidates for next generation lithium-ion batteries due to their high specific capacity and low cost. However, lattice deoxidation associated with elemental migration and internal local shrinkage usually results in deteriorated cyclic performance and notorious voltage attenuation, severely limiting its application. In this paper, we have successfully injected uniform oxygen defects into surface region of Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 primary particles under the high-pressure and weak carbonate environment. Various experimental investigations indicate that the injected robust oxygen defects can not only mitigate detrimental interfacial reactions but also suppress unfavorable lattice variation and particle breakage. More importantly, theoretical calculations unravel the critical roles of oxygen defects in regulating energy band structure for strengthened anionic reversibility. Owing to stabilization effects of unique oxygen defect engineering, the modified Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 cathode has harvested dramatically enhanced electrochemical performance including a high initial coulombic efficiency of 96.6%, an outstanding capacity retention of 91.96% (1C, 200 cycles) and suppressed voltage decay of only 1.62 mV per cycle. Therefore, this facile and effective defect engineering strategy could establish new guidance for promoting practical application of Li-rich Mn-based cathode material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗