Engineering topics

Shanov, Vesselin

Publications and source records attributed to Shanov, Vesselin.

4 records

DOE OSTI2024

Directing CO 2 electroreduction pathways for selective C 2 product formation using single-site doped copper catalysts

Manipulating the selectivity-determining step in post-C–C coupling is crucial for enhancing C 2 product specificity during electrocatalytic CO 2 reduction, complementing efforts to boost rate-determining step kinetics. Here we highlight the role of single-site noble metal dopants on Cu surfaces in influencing C–O bond dissociation in an oxygen-bound selectivity-determining intermediate, steering post-C–C coupling toward ethylene versus ethanol. Integrating theoretical and experimental analyses, we demonstrate that the oxygen binding strength of the Cu surface controls the favorability of C–O bond scission, thus tuning the selectivity ratio of ethylene-to-ethanol. The Rh-doped Cu catalyst with optimal oxygen binding energy achieves a Faradaic efficiency toward ethylene of 61.2% and an ethylene-to-ethanol Faradaic efficiency ratio of 4.51 at –0.66 V versus RHE (reversible hydrogen electrode). Integrating control of both rate-determining and selectivity-determining steps further raises ethylene Faradaic efficiency to 68.8% at 1.47 A cm -2 in a tandem electrode. Our insights guide the rational design of Cu-based catalysts for selective CO 2 electroreduction to a single C 2 product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

CO-promoted low-temperature conversion of CH 4 to hydrogen and carbon nanotubes on Nanocrystalline Cr-doped ferrite catalyst

Catalytic decomposition of methane (CDM) to H 2 and multiwalled carbon nanotubes (MWCNTs) was achieved by a nanocrystalline Cr-doped ferrite (FeCr) catalyst at 500 °C and atmospheric pressure with minor cofed CO. The exothermic Boudouard reaction increased the temperature and H 2 from CDM at catalyst surface that induced Fe 2+ reduction to Fe 0 . The Fe 0 clusters along with the CO-originated surface oxygens enabled transfer of C and H to sustain the surface CDM and CO reactions. The metallic Fe-enabled C transfer led to the formation of MWCNTs. The Cr 6+/3+ dopants facilitated the Fe redox cycles and maintained surface oxygens for high catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Planar defect-driven electrocatalysis of CO 2 -to-C 2 H 4 conversion

The selectivity towards a specific C 2+ product, such as ethylene (C 2 H 4 ), is sensitive to the surface structure of copper (Cu) catalysts in carbon dioxide (CO 2 ) electro-reduction. The fundamental understanding of such sensitivity can guide the development of advanced electrocatalysts, although it remains challenging at the atomic level. In this work, we demonstrated that planar defects, such as stacking faults, could drive the electrocatalysis of CO 2 -to-C 2 H 4 conversion with higher selectivity and productivity than Cu(100) facets in the intermediate potential region (–0.50 ~ –0.65 V vs. RHE). The unique right bipyramidal Cu nanocrystals containing a combination of (100) facets and a set of parallel planar defects delivered 67% faradaic efficiency (FE) for C 2 H 4 and a partial current density of 217 mA cm –2 at –0.63 V vs. RHE. In contrast, Cu nanocubes with exclusive (100) facets exhibited only 46% FE for C 2 H 4 and a partial current density of 87 mA cm –2 at an identical potential. Both ex situ CO temperature-programmed desorption and in situ Raman spectroscopy analysis implied that the stronger *CO adsorption on planar defect sites facilitates CO generation kinetics, which contributes to a higher surface coverage of *CO and in turn an enhanced reaction rate of C–C coupling towards C 2+ products, especially C 2 H 4 .

36 MATERIALS SCIENCE↗

DOE OSTI2020

Carbon Nanotube Formation on Cr-Doped Ferrite Catalyst during Water Gas Shift Membrane Reaction: Mechanistic Implications and Extended Studies on Dry Gas Conversions

A nanocrystalline chromium-doped ferrite (FeCr) catalyst was shown to coproduce H2 and multiwalled carbon nanotubes (MWCNTs) during water gas shift (WGS) reaction in a H2-permselective zeolite membrane reactor (MR) at reaction pressures of ~20 bar. The FeCr catalyst was further demonstrated in the synthesis of highly crystalline and dimensionally uniform MWCNTs from a dry gas mixture of CO and CH4, which were the apparent sources for MWCNT growth in the WGS MR. In both the WGS MR and dry gas reactions, the operating temperature was 500 °C, which is significantly lower than those commonly used in MWCNT production by chemical vapor deposition (CVD) method from CO, CH4, or any other precursor gases. Extensive ex situ characterizations of the reaction products revealed that the FeCr catalyst remained in partially reduced states of Fe3+/Fe2+ and Cr6+/Cr3+ in WGS membrane reaction while further reduction of Fe2+ to Fe0 occurred in the CO/CH4 dry gas environments. The formation of the metallic Fe nanoparticles or catalyst surface dramatically improved the crystallinity and dimensional uniformity of the MWCNTs from dry gas reaction as compared to that from WGS reaction in the MR. Reaction of the CO/CH4 mixture containing 500 ppmv H2S also resulted in high-quality MWCNTs similar to those from the H2S-free feed gas, demonstrating excellent sulfur tolerance of the FeCr catalyst that is practically meaningful for utilization of biogas and cheap coal-derived syngas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗