Engineering topics

Sellers, J. F.

Publications and source records attributed to Sellers, J. F..

10 records

NASA NTRS1981

Army/NASA small turboshaft engine digital controls research program

The emphasis of a program to conduct digital controls research for small turboshaft engines is on engine test evaluation of advanced control logic using a flexible microprocessor based digital control system designed specifically for research on advanced control logic. Control software is stored in programmable memory. New control algorithms may be stored in a floppy disk and loaded directly into memory. This feature facilitates comparative evaluation of different advanced control modes. The central processor in the digital control is an Intel 8086 16 bit microprocessor. Control software is programmed in assembly language. Software checkout is accomplished prior to engine test by connecting the digital control to a real time hybrid computer simulation of the engine. The engine currently installed in the facility has a hydromechanical control modified to allow electrohydraulic fuel metering and VG actuation by the digital control. Simulation results are presented which show that the modern control reduces the transient rotor speed droop caused by unanticipated load changes such as cyclic pitch or wind gust transients.

Sellers, J. F.↗

NASA NTRS1980

Propulsion system mathematical model for a lift/cruise fan V/STOL aircraft

A propulsion system mathematical model is documented that allows calculation of internal engine parameters during transient operation. A non-realtime digital computer simulation of the model is presented. It is used to investigate thrust response and modulation requirements as well as the impact of duty cycle on engine life and design criteria. Comparison of simulation results with steady-state cycle deck calculations showed good agreement. The model was developed for a specific 3-fan subsonic V/STOL aircraft application, but it can be adapted for use with any similar lift/cruise V/STOL configuration.

Cole, G. L.↗

NASA NTRS1977

Analysis of control concepts for gas and shaft-coupled V/STOL aircraft lift fan systems

For lift-fan powered V/STOL aircraft, two unconventional propulsion system types were proposed. The first type uses fans connected by hot gas ducting, and the second type uses fans connected by cross shafting. An analytical study identified the basic steady-state and dynamic characteristics for each type of system. For the gas-coupled system, the control concepts analyzed were variable-area fan turbines and throttling valves in the ducting. For the shaft-coupled system, the control concepts analyzed were variable-pitch fans and variable fan inlet guide vanes. All of these concepts are capable of meeting V/STOL aircraft control moment and transient response requirements when appropriate propulsion controls are used.

Sellers, J. F.↗

NASA NTRS1977

Analysis of control concepts for gas and shaft-coupled V/STOL aircraft lift fan systems

V/STOL aircraft rely on their propulsion systems to provide lift and attitude control moments during hover and low-speed flight. For lift-fan powered V/STOL aircraft, two unconventional propulsion system types have been proposed. The first type uses fans connected by hot gas ducting, and the second type uses fans connected by cross shafting. This paper presents results of an analytical study which identifies the basic steady-state and dynamic characteristics for each type of system. For the gas-coupled system, the control concepts analyzed were variable-area fan turbines and throttling valves in the ducting. For the shaft-coupled system, the control concepts analyzed were variable-pitch fans and variable fan inlet guide vanes. All of these concepts are shown to be capable of meeting V/STOL aircraft control moment and transient response requirements when appropriate propulsion controls are used. Each type of system has unique problem areas which require an integrated approach to aircraft/propulsion control design.

Sellers, J. F.↗

NASA NTRS1976

DYNGEN

Steady-state and transient performance of turbofan and turbojet engines are analyzed. Program uses large time steps, gives analyst freedom in selecting equations needed to describe system, and eliminates discrepancies in answers often generated by transient and steady-state simulations.

Sellers, J. F.↗

NASA NTRS1975

DYNGEN: A program for calculating steady-state and transient performance of turbojet and turbofan engines

The DYNGEN, a digital computer program for analyzing the steady state and transient performance of turbojet and turbofan engines, is described. The DYNGEN is based on earlier computer codes (SMOTE, GENENG, and GENENG 2) which are capable of calculating the steady state performance of turbojet and turbofan engines at design and off-design operating conditions. The DYNGEN has the combined capabilities of GENENG and GENENG 2 for calculating steady state performance; to these the further capability for calculating transient performance was added. The DYNGEN can be used to analyze one- and two-spool turbojet engines or two- and three-spool turbofan engines without modification to the basic program. A modified Euler method is used by DYNGEN to solve the differential equations which model the dynamics of the engine. This new method frees the programmer from having to minimize the number of equations which require iterative solution. As a result, some of the approximations normally used in transient engine simulations can be eliminated. This tends to produce better agreement when answers are compared with those from purely steady state simulations. The modified Euler method also permits the user to specify large time steps (about 0.10 sec) to be used in the solution of the differential equations. This saves computer execution time when long transients are run. Examples of the use of the program are included, and program results are compared with those from an existing hybrid-computer simulation of a two-spool turbofan.

Sellers, J. F.↗

NASA NTRS1973

Transient analysis of energy Transfer Control (ECT) and compressor bleed concepts of remote lift fan control

The transient performance of two concepts for control of vertical takeoff aircraft remote lift fans is analyzed and discussed. Both concepts employ flow transfer between pairs of lift fans located in separate parts of the aircraft in order to obtain attitude control moments for hover and low-speed flight. The results presented are from a digital computer, dynamic analysis of the YJ97/LF460 remote drive turbofan. The transient responses of the two systems are presented for step demands in lift and moment.

Sellers, J. F.↗

NASA NTRS1973

Steady state analysis of Energy Transfer Control (ETC) and compressor bleed concepts of remote lift fan control

Two new concepts of control for VTOL aircraft remote lift fans are analyzed and discussed. Both concepts employ flow transfer among lift fans located in separate parts of the aircraft in order to obtain attitude control moments in hover and low-speed flight. The results presented are from a digital computer analysis of the YJ97/LF460 remote drive turbofan, although qualitative conclusions should apply to any remote fan system. The basic operating principles of the two systems are described, and their steady-state moment generating capabilities are discussed. Lift-recovery strategies for component failures are also analyzed.

Sellers, J. F.↗

NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft.

This paper presents the results of an analytical study of the dynamics and control of turbofan lift engines, and proposes methods of meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed.

Sellers, J. F.↗

NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft

The use of turbofan engines as lift units for VTOL aircraft poses new engine control problems. At low flight speeds, the lift units must provide the fast thrust response needed for aircraft attitude and height control. The results are presented of an analytical study of the dynamics and control of turbofan lift engines, and methods are proposed for meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed. Both methods are shown to have thrust response near the required levels.

Sellers, J. F.↗