Engineering topics

Seitzman, Natalie

Publications and source records attributed to Seitzman, Natalie.

6 records

DOE OSTI2023

Dynamic In‐Plane Heterogeneous and Inverted Response of Graphite to Fast Charging and Discharging Conditions in Lithium‐Ion Pouch Cells

Solutions for improving fast charging of lithium‐ion batteries have largely focused on alleviating through‐plane lithiation gradients while little is understood about in‐plane heterogeneities and how to resolve them. Herein, high‐speed synchrotron X‐ray diffraction (XRD) resolves graphite lithiation spatially and temporally during 6 C charging and 2 C discharging. At every point during operation, considerable differences in the state of lithiation across the pouch cell are present. Some regions are more responsive to operation than others, reaching full lithiation early during charge and full delithiation during discharge. Other regions within the cell never fully delithiate during discharge, despite a prolonged voltage hold at 2.8 V. Using time‐resolved XRD data, the calculated local current density (mA cm −2 ) at the graphite surface shows an unexpected occurrence of local inverted current densities where regions of graphite are observed to delithiate during charging and lithiate during discharging. A pseudo‐3D model is developed for the graphite electrode with spatially varying microstructural tortuosity to show how microstructural heterogeneity could influence spatial charge dynamics. The model could not predict the complex in‐plane charge behavior observed within the cell. Consequently physics‐based charging protocols based on homogeneous electrode assumptions may underestimate the local variations in charge dynamics and occurrence of lithium plating.

25 ENERGY STORAGE↗

DOE OSTI2021

Operando X-Ray Tomography Imaging of Solid-State Electrolyte Response to Li Evolution under Realistic Operating Conditions

Solid-state Li-ion conductors are a next-generation battery technology that are particularly promising for electric vehicles, offering the capacitive benefits of Li metal anodes with nonflammable electrolytes. Microstructural evolution in these solid-state batteries, especially the Li anode, requires deeper understanding of the conditions under which certain undesired behaviors are more likely to occur. This study utilizes operando X-ray computed tomography to visualize the behavior of lithium in response to device operation, considering variables that are relevant to a realistic battery: stack pressure, microscale defects such as pores, and temperature. This work demonstrates that experimental and operational conditions, especially temperature, affect the fundamental driving forces of realistic solid electrolyte systems and provides visual insight into possible mechanisms of Li migration. In particular, the effect of these variables on Li propagation from the anode through pre-existing defects and Li nucleation within the imperfectly electron-insulating electrolyte is highlighted.

battery↗

DOE OSTI2020

Highly Reversible Plating/Stripping of Porous Zinc Anodes for Multivalent Zinc Batteries

Zinc continues to garner immense interest due to its versatility as an anode material in several configurations utilizing either alkaline or mild-pH electrolytes. Current research on using mild-pH electrolytes has improved the rechargeability aspect of Zn-based batteries since Zn2+ is solely utilized for plating/stripping of Zn. Several studies have incorporated Zn metal foils, yet, dramatic improvements can be achieved by expressing Zn as a porous structure. Herein, we use a quasi-pulsed electrodeposition process to prepare a conformal Zn coating onto 3D porous copper foam. By tuning the electrodeposition parameters, we achieved an optimal Zn coating that undergoes reversible plating/stripping when tested in symmetric Zn cells, which supported a low overpotential of ~60 mV for up to 100 cycles. We further investigated changes in the surface morphology by studying the Zn surface of both foil and 3D structure using scanning electron microscopy and X-ray micro-computed tomography. Both techniques showed that the Zn foil undergoes dramatic alterations at the surface, which results in inhomogeneous deposition of Zn, whereas the 3D form exhibited minimal changes. Lastly, we paired both Zn foil and 3D Zn with vanadium oxide and demonstrated that the porous structure supports high rate capability and high specific capacity.

25 ENERGY STORAGE↗

DOE OSTI2020

NASICON Na 3 V 2 (PO 4 ) 3 Enables Quasi-Two-Stage Na + and Zn 2+ Intercalation for Multivalent Zinc Batteries

Identifying positive electrode materials capable of reversible multivalent electrochemistry in electrolytes containing divalent ions such as Mg 2+ , Ca 2+ , and Zn 2+ at high operating potentials remains an ongoing challenge in “beyond lithium-ion” research. In this paper, we explore the Zn 2+ charge-storage mechanism of a vanadium-based Na + superionic conductor (NASICON), Na 3 V 2 (PO 4 ) 3 . By using X-ray synchrotron techniques to unravel potential-dependent structure–property relationships, we ascribe the reversible electrochemical behavior of Na 3 V 2 (PO 4 ) 3 to a quasi-two-stage intercalation process that involves both Na+ and Zn 2+ . Initial charging of Na 3 V 2 (PO 4 ) 3 leads to a Na + -extracted phase corresponding to Na 3 V 2 (PO 4 ) 3 , whereas subsequent discharge results predominantly in Na + intercalation followed by Zn 2+ intercalation. Operando X-ray diffraction of Na 3 V 2 (PO 4 ) 3 was used to study the phase changes associated with the first charge/discharge process, and ex situ measurements were used to precisely link the changes in the crystal structure to a quasi-two-stage intercalation of Na + and Zn 2+ . The corresponding changes in the V-oxidation state, V-O coordination, and the presence of Zn 2+ were confirmed by X-ray absorption spectroscopy. The results of this work present a comprehensive understanding of the charge-storage properties for a well-established NASICON structure that confers both the high capacity (~100 mA h g -1 ) and high potential (1.35 and 1.1 V vs Zn/Zn 2+ ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Spatial quantification of dynamic inter and intra particle crystallographic heterogeneities within lithium ion electrodes

The performance of lithium ion electrodes is hindered by unfavorable chemical heterogeneities that pre-exist or develop during operation. Time-resolved spatial descriptions are needed to understand the link between such heterogeneities and a cell's performance. Here, operando high-resolution X-ray diffraction-computed tomography is used to spatially and temporally quantify crystallographic heterogeneities within and between particles throughout both fresh and degraded Li x Mn 2 O 4 electrodes. This imaging technique facilitates identification of stoichiometric differences between particles and stoichiometric gradients and phase heterogeneities within particles. Through radial quantification of phase fractions, the response of distinct particles to lithiation is found to vary; most particles contain localized regions that transition to rock salt LiMnO 2 within the first cycle. Other particles contain monoclinic Li 2 MnO 3 near the surface and almost pure spinel LixMn2O4 near the core. Following 150 cycles, concentrations of LiMnO 2 and Li 2 MnO 3 significantly increase and widely vary between particles.

25 ENERGY STORAGE↗

DOE OSTI2020

Improved Stability and Cyclability of Ceramic Solid Electrolyte by Coating Polymer

Rechargeable all-solid-state lithium (Li) metal batteries show better safety and energy density compared to commercial Li-ion batteries using liquid electrolyte. As the key component of Li metal batteries, ceramic solid-state electrolyte has attracted great interest because of its high ion conductivity and great potential in interfacing with Li metal. Ceramic electrolyte has a more stable interface with Li metal than liquid electrolyte, but chemical reaction and Li dendrite growth at the electrolyte/Li interface are still significant, which causes device degradation and failure by cycling of Li plating and stripping. Unlike ceramic electrolyte, polymer electrolyte has a relatively stable interface with Li metal and better mechanical flexibility. Therefore, we introduced a polymer electrolyte coating to protect the ceramic electrolyte from direct contact with Li metal. The galvanotactic cycling Li plating/striping data on the devices with (without) the coating illustrates increased (decreased) overall conductivity and cyclability of the test cell by the cycling. Nanometer-scale ionic-transport imaging, based on atomic force microscopy, shows that cycling degrades the ceramic-only electrolyte by partially blocking ionic transport in areas; in contrast, cycling on the polymer-coated electrolyte improves ionic conductivity. Compared with the ceramic-only electrolyte, this novel polymer electrolyte coating on ceramic electrolyte shows less degradation when in contact with Li metal.

25 ENERGY STORAGE↗