Engineering Papers⌕ Search

Engineering topics

Schweiger, Michael J

Publications and source records attributed to Schweiger, Michael J.

At least 19 records

Structure of rhenium-containing sodium borosilicate glass

A series of sodium borosilicate glasses were synthesized with increasing fractions of KReO4 or Re2O7, to 10000 ppm (1 mass%) target Re in glass, to assess the effects of large concentrations of rhenium on glass structure and to estimate the solubility of technetium, a radioactive component in typical low active waste nuclear waste glasses. Magic angle spinning nuclear magnetic resonance (MAS-NMR), Fourier transform infrared (FTIR) spectroscopy, and Raman spectroscopy were performed to characterize the glasses as a function of Re source additions. In general, silicon was found coordinated in a mixture of Q2 and Q3 structural units, while Al was 4-coordinated and B was largely 3-coordinate and partially 4-coordinated. The rhenium source did not appear to have significant effects on the glass structure. Thus, at the up to the concentrations that remain in dissolved in glass, ~3000 ppm Re by mass maximum. , the Re appeared to be neither a glass-former nor a strong glass modifier., Rhenium likely exists in isolated ReO4- anions in the interstices of the glass network, as evidenced by the polarized Raman spectrum of the Re glass in the absence of sulfate. Analogous to SO42-¬ in similar glasses, ReO4- is likely a network modifier and forms alkali salt phases on the surface and in the bulk glass above solubility.

borosilicate glass↗

The liquidus temperature of nuclear waste glasses: an international Round-Robin Study

Ten institutions from five countries participated in a Round Robin study to contribute to the Precision and Bias section of an American Society for Testing and Materials standard procedure that Pacific Northwest National Laboratory (PNNL) is developing for measuring the liquidus temperature (TL) of radioactive and simulated waste glasses. In this study, three separate TL measurement methods were a gradient temperature (GT) method, a uniform temperature (UT) method, and a crystal fraction extrapolation (CF) method. Three different glasses were measured with a combination of these three methods. The TL values reported by different institutions are generally consistent and vary within a narrow range. The precision of a TL measurement was evaluated as ±10°C regardless of the method used for making the measurement. The Round Robin glasses were all previously studied at PNNL and included ARG-1 (Glass A), Zr-9 (Glass B), and AmCm2-19 (Glass C), with measured TL values spanning the temperature range ~960-1240°C. The three methods discussed here in more detail are the GT, UT, and CF methods. A best-case precision for TL has been obtained from the data, even though the data were not acquired for all three glasses using all three methods from each participating organization.

ASTM↗

Rhenium Solubility in Borosilicate Nuclear Waste Glass: Implications for the Processing and Immobilization of Technetium-99

The immobilization of 99Tc in a suitable host matrix has proved to be an arduous task for the researchers in nuclear waste community around the world. At the Hanford site in Washington State, the total amount of 99Tc in low-activity waste (LAW) is ~1300 kg and the current strategy is to immobilize the 99Tc in borosilicate glass with vitrification. In this context, the present article reports on the solubility/retention of rhenium, a nonradioactive surrogate for 99Tc, in a LAW borosilicate glass. Due to the radioactive nature of technetium, rhenium was chosen as a simulant because of the similarity between their ionic radii and other chemical aspects. The glasses containing Re (0 – 10,000 ppm by mass) were synthesized in vacuum-sealed quartz ampoules in order to minimize the loss of Re by volatilization during melting at 1000 °C. The rhenium was found to predominantly exist as Re (VII) in all the glasses as observed by X-ray absorption near-edge structure (XANES). The solubility of Re in borosilicate glasses was determined to be ~3000 ppm (by mass) with inductively coupled plasma-optical emission spectroscopy (ICP-OES). At higher rhenium concentrations, some additional material was retained in the glasses in the form of crystalline inclusions that were detected by X-ray diffraction (XRD) and laser ablation-ICP mass spectrometry (LA-ICP-MS). The implications of these results on the immobilization of 99Tc from radioactive wastes in borosilicate glasses have been discussed.

borosilicate glass↗

DWPF STARTUP FRIT VISCOSITY MEASUREMENT ROUND ROBIN RESULTS

A viscosity standard is needed to replace the National Institute of Standards and Technology (NIST) glasses currently being used to calibrate viscosity measurement equipment. The current NIST glasses are either unavailable or less than ideal for calibrating equipment to measure the viscosity of high-level waste glasses. This report documents the results of a viscosity round robin study conducted on the Defense Waste Processing Facility (DWPF) startup frit. DWPF startup frit was selected because its viscosity-temperature relationship is similar to most DWPF and Hanford high-level waste glass compositions. The glass underwent grinding and blending to homogenize the large (100 lb) batch. Portions of the batch were supplied to the laboratories (named A through H) for viscosity measurements following a specified temperature schedule with a temperature range of 1150 C to 950 C and with an option to measure viscosity at lower temperatures if their equipment was capable of measuring at the higher viscosities. Results were used to fit the Vogel-Tamman-Fulcher and Arrhenius equations to viscosity as a function of temperature for the entire temperature range of 460 C through 1250 C as well as the limited temperature interval of approximately 950 C through 1250 C. The standard errors for confidence and prediction were determined for the fitted models.

36 MATERIALS SCIENCE↗

Effect of Alumina Source on the Rate of Melting Demonstrated with Nuclear Waste Glass Batch

The melting behaviors of three glass batches formulated to vitrify high-level waste were compared. These batches, otherwise identical, differed in the alumina source: one was prepared with corundum (Al2O3), another with gibbsite [Al(OH)3], and the other with boehmite [AlO(OH)]. Batch samples, in the form of loose batches or pressed pellets, were heated at 5°C/min up to 1200°C. The expansion of pellets was monitored photographically. Quenched samples of batches, heated in crucibles, were thin-sectioned, investigated with optical microscopy, and analyzed with X-ray diffraction to quantify crystalline phases. Finally, batch-to-glass conversion was investigated with thermal analysis. Corundum was still present in one batch up to 900°C whereas gibbsite and boehmite dissolved below 500°C. In the batch with corundum, quartz, the source of silica, dissolved marginally earlier than in the batches with gibbsite and boehmite. Unlike the batch with corundum that exhibited considerable foaming, the batches with gibbsite and boehmite did not produce primary foam and made a more homogeneous glass. The occurrence of primary foam in the batch with corundum is a likely cause of a low rate of melting within the cold cap of a large-scale electric melter.

Pierce, David A↗

Structural analysis of some sodium and alumina rich high-level nuclear waste glasses

Sodium and aluminum rich high level nuclear waste glasses are prone to nepheline (NaAlSiO4) crystallization. Since nepheline removes three moles of glass forming oxides (Al2O3 and SiO2) per each mole of Na2O, its formation can result in sever deterioration of the chemical durability. The present study aims at investigating the relationships between the molecular-level structure of sodium alumino-borosilicate based simulated high-level nuclear waste glasses and their crystallization behavior by infrared spectroscopy (FTIR) and x-ray diffraction, respectively. The molecular structure of most of the investigated glasses comprises of a mixture of Q2 and Q3 (Si) units while aluminum and boron are predominantly present in tetrahedral and trigonal coordination, respectively. The increasing boron content has been shown to suppress the nepheline formation in the glasses. The structural influence of various glass components on nepheline crystallization has been discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Glass Formulation for Next Generation Cold Crucible Induction Melter

Transformational melter technologies are being considered to support mission acceleration within the U.S. Department of Energy (DOE) complex. New glass formulations are required to take full advantage of the next generation melters, for example, the cold crucible induction melter (CCIM). The key advantage of CCIM technology over current reference technologies is its capability to provide higher processing temperatures, which can lead to an increased waste throughput rate by achieving higher waste loadings and by increasing the feed processing rate. Various waste compositions within the DOE complex were evaluated to determine their potential for successfully demonstrating the unique advantages of the CCIM technology. Glass formulations that satisfy a set of constraints for product quality and assumed CCIM processing conditions were developed for two Hanford waste streams, AZ-101 high-level waste (HLW) and AN-105 low-activity waste (LAW). Three glasses selected for AZ-101 HLW have waste loadings of 40, 42.5, and 45 wt%. The 45-wt% waste loading corresponds to a 22% increase from 37 wt%, which is the maximum expected waste loading based on the current reference formulation. One glass selected for AN-105 LAW has a waste loading of 31.3 wt% at 24 wt% Na2O in glass, which is a 14% increase from the current reference formulation maximum of 21 wt% Na2O. These four glasses are planned for scaled melter tests for initial demonstration of the CCIM technologies for Hanford wastes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nepheline Crystallization in Nuclear Waste Glasses: Progress toward acceptance of high-alumina formulations

We have critically compiled and analyzed historical data for investigating the quantity of nepheline (NaAlSiO4) precipitation as a function of composition in simulated nuclear waste glasses. To understand composition we used two primary methods: 1) investigating the Al2O3-SiO2-Na2O ternary with filtering for different B2O3 levels and 2) creating a quadrant system consisting of compositions reduced to two metric numbers. These metrics are 1) the nepheline discriminator (ND) which depends only on the SiO2 content by weight normalized to the total weight of the Al2O3-SiO2-Na2O sub-mixture and 2) the optical basicity (OB) which contains contributions from all constituents in the glass. Nepheline precipitation is expected to be suppressed at high SiO2 levels (ND >0.62) or at low basicities (OB <0.55 to 0.57). Changes in sodium aluminosilicate glass OB due to additions of CaO and B2O3 correlate with observed effects on nepheline formation. We propose that additional composition space is available for formulating high-waste-loading, high-Al¬2O3 nuclear waste glasses when Na2O levels are less than ~0.125 (normalized by weight on the Al2O3-SiO2-Na2O sub-mixture). However, this compositional space is considerably extended to higher Na2O levels when adding >5 wt% B2O3. The OB concept can help further refine regions of nepheline-free glass formation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Iron Phosphate Glass-Containing Hanford Waste Simulant

Resolution of the nation’s high level tank waste legacy requires the design, construction, and operation of large and technically complex one-of-a-kind processing waste treatment and vitrification facilities. While the ultimate limits for waste loading and melter efficiency have yet to be defined or realized, significant reductions in glass volumes for disposal and mission life may be possible with advancements in melter technologies and/or glass formulations. This test report describes the experimental results from a small-scale test using the research scale melter (RSM) at Pacific Northwest National Laboratory (PNNL) to demonstrate the viability of iron phosphate-based glass with a selected waste composition that is high in sulfates (4.37 wt% SO3). The primary objective of the test was to develop data to support a cost-benefit analysis as related to the implementation of phosphate-based glasses for Hanford low activity waste (LAW) and/or other high-level waste streams within the U.S. Department of Energy complex. The testing was performed by PNNL and supported by Idaho National Laboratory, Savannah River National Laboratory, and Mo-Sci Corporation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of Particle Size Distribution on Slurry Rheology: Nuclear Waste Simulant Slurries

Controlling the rheological properties of slurries has been of great interest in various industries such as cosmetics, ceramic processing, and nuclear waste treatment. Many physicochemical parameters, such as particle size, pH, ionic strength, and mass/volume fraction of particles, can influence the rheological properties of slurry. Among such parameters, the particle size distribution of slurry would be especially important for nuclear waste treatment because most nuclear waste slurries show a broad particle size distribution. We studied the rheological properties of several different low activity waste nuclear simulant slurries having different particle size distributions under high salt and high pH conditions. Using rheological and particle size analysis, it was found that the percentage of colloid-sized particles in slurry appears to be a key factor for rheological characteristics and the efficiency of rheological modifiers. This behavior was shown to be coupled with an existing electrostatic interaction between particles under a low salt concentration. Our study suggests that one may need to implement the particle size distribution as a critical factor to understand and control rheological properties in nuclear waste treatment plants, such as the U.S. Department of Energy’s Hanford and Savannah River sites, because the particle size distributions significantly vary over different types of nuclear waste slurries.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Conversion of batch to molten glass, I: Volume expansion

Batches designed to simulate nuclear high-level waste glass were compressed into pellets that were heated at a rate of 5 K/min and photographed to obtain the profile area as a function of temperature. Three types of batches were prepared with different nitrate-carbonate ratios. To determine the impact of the heat supply by an exothermic reaction and the batch expansion, the nitrated batches were prepared with varying addition of sucrose. To obtain the impact of the grain size of the quartz component, the mixed nitrate-carbonate batches were prepared with silica particles ranging in size from 5 µm to 195 µm. One batch containing only carbonates was also tested. Sucrose addition had little effect on the batch expansion, while the size of silica was very influential. The 5-μm grains had a strongest effect, causing the generation of both primary and secondary foam, whereas only secondary foam was produced in batches with grains of 45 µm and larger. The retention of gases evolved as the batch melts creates primary foam. Gases evolved from oxidation-reduction reactions once the batch has melted produce secondary foam. We suggest that the viscosity of the melt and the amount of gas evolved are the main influences on foam production. As more gas is produced in the melt and as the glass becomes less viscous, the bubbles of gas coalesce into larger and larger cavities, until the glass can no longer contain the bubbles and they burst, causing the foam to collapse.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Conversion of batch to molten glass, II: Dissolution of quartz particles

Quartz dissolution during the batch-to-glass conversion influences the melt viscosity and ultimately the temperature at which the glass forms. Batches to make a high-alumina borosilicate glass (formulated for the vitrification of nuclear waste) were heated as 5°C min-1 and quenched from the temperatures of 400-1200°C at 100°C intervals. As a silica source, the batches contained quartz with particles ranging from 5 to 195 µm. The content of unreacted quartz in the samples was determined with x-ray diffraction. Most of fine quartz has dissolved during the early batch reactions (at temperatures <800°C), whereas coarser quartz dissolved mostly in a continuous glass phase via diffusion. The mass-transfer coefficients were assessed from the data as functions of the initial particle sizes and the temperature. A series of batch was also tested that contained nitrated components and additions of sucrose known to accelerate melting. While sucrose addition had no discernible impact on quartz dissolution, nitrate batches melted somewhat more slowly than batches containing carbonates and hydroxides in addition to nitrates.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Expanded High-Level Waste Glass Property Data Development: Phase I

Two separate test matrices were developed as part if the EM-21 Glass Matrix Crucible Testing. The first matrix, developed using a single component-at-a-time design method and covering glasses of interest primarily to Hanford, is addressed in this data package. This data package includes methods and results from glass fabrication, chemical analysis of glass compositions, viscosity, electrical conductivity, liquidus temperature, canister centerline cooling, product consistency testing, and the toxicity characteristic leach procedure.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

ALKALI/ AKALINE-EARTH CONTENT EFFECTS ON PROPERTIES OF HIGH-ALUMINA NUCLEAR WASTE GLASSES

A series of high alumina (>20 mass %) borosilicate glasses have been made and characterized based on the assumption that the primary modifier cation field strength plays a significant role in mediating glass structure of nuclear waste glasses. Any crystallization upon quenching or after heat treatment at 950 °C for 24 hours was identified and quantified by X-ray diffraction. Particular note was take of any aluminosilicates formed, such as those in the nepheline group (MAlSiO4 where M=K, Na, Li), as these remove multiple glass-formers from the network upon crystallization. The relative roles of potassium, sodium, lithium, calcium, and magnesium on glass structure and crystallization in high alumina glasses were explored using Raman and infrared vibrational spectroscopy. Strong evidence was found for the importance of 4 membered rings in glasses with 10 mol % alkaline earths (Ca, Mg).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of Quartz Particle Size and Sucrose Addition on Melting Behavior of a Melter Feed for High-Level Waste Glass

The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5°C/min up to 1200°C. The initial size of quartz particles in feed ranged from 5 to 195 µm. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-μm quartz particles; particles >150 µm formed clusters. Particles of 5 µm completely dissolved by 900°C whereas particles >150 µm did not fully dissolve even when the temperature reached 1200°C. Sucrose addition had virtually zero impact on both foaming and the dissolution of silica particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cluster formation of silica particles in glass batches during melting

The study describes the incorporation of solid silica into molten glass during glass-batch melting as a function of the grain size in the range from 5 to 275 µm. Whereas tiny grains formed a bubbly melt, very large grains formed slowly dissolving cluster. Silica grains are forced to clusters by rising bubbles. The impact of the silica grain size on the glass-forming melt viscosity, overall density, thermal conductivity, and compositional homogeneity, as well as the consequences of these effects on glass processing in melting furnaces, is discussed. A high-alumina borosilicate glass for nuclear waste vitrification was chosen for the study, but the authors believe that the observed behaviors occur also in melting of commercial batches.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Predictive Power of Electronic Polarizability for Tailoring the Refractivity of High Index Glasses Optical Basicity Versus the Single Oscillator Model

Four compositions of high density (~8 g/cm3) heavy metal oxide glasses composed of PbO, Bi2O3, and Ga2O3 were produced and refractivity parameters (refractive index and density) were computed and measured. Optical basicity was computed using three different models – average electronegativity, ionic-covalent parameter, and energy gap – and the basicity results were used to compute oxygen polarizability and subsequently refractive index. Refractive indices were measured in the visible and infrared at 0.633 μm, 1.55 μm, 3.39 μm, 5.35 μm, 9.29 μm, and 10.59 μm using a unique prism coupler setup, and data were fitted to the Sellmeier expression to obtain an equation of the dispersion of refractive index with wavelength. Using this dispersion relation, single oscillator energy, dispersion energy, and lattice energy were determined. Oscillator parameters were also calculated for the various glasses from their oxide values as an additional means of predicting index. Calculated dispersion parameters from oxides underestimate the index by 3 to 4%. Predicted glass index from optical basicity, based on component oxide energy gaps, underpredicts the index at 0.633 μm by only 2%, while other basicity scales are less accurate. The predicted energy gap of the glasses based on this optical basicity overpredicts the Tauc optical gap as determined by transmission measurements by 6 to 10%. These results show that for this system, density, refractive index in the visible, and energy gap can be reasonably predicted using only composition, optical basicity values for the constituent oxides, and partial molar volume coefficients. Calculations such as these are useful for a priori prediction of optical properties of glasses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Gleenglass Swarf Research

Objective: John Sauer, Gleenglass principal, asked for research into innovative uses for a reclaimed glass slurry, also referred to as swarf. Through our research we were to determine a product and a market that could be manufactured using this fully recycled glass swarf. Background: Mr. Sauer receives the swarf from major glass manufacturers as a fine powder glass suspended in an organic dispersant and water. The swarf is produced through an industrial glass cutting process that results in the glass powder dispersed in water and recyclable glass disks; both are used in the project. Mr. Sauer's swarf studio testing has yet to produce any product with a value great enough to justify processing the swarf. Many of these limitations were believed to be due to the unknown composition and characteristics of the swarf as well as the limited lab testing ability of Mr. Sauer in his studio space. Deliverables: 1. The valuable characteristics of the swarf. 2. Products that can be produced with the swarf. 3. Market for developed products. 4. Capital investment needed to create developed product. 5. Any other applications of the swarf that were outside the scope of residential and commercial building material for use in future DOE grant proposals to the glass manufacturing facilities. 6. Additives that could change the color of the final piece to white, gray, or green.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗