Engineering Papers⌕ Search

Engineering topics

Schneider, Matthew M.

Publications and source records attributed to Schneider, Matthew M..

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High‐throughput combinatorial approach expedites the synthesis of a lead‐free relaxor ferroelectric system

Abstract Developing novel lead‐free ferroelectric materials is crucial for next‐generation microelectronic technologies that are energy efficient and environment friendly. However, materials discovery and property optimization are typically time‐consuming due to the limited throughput of traditional synthesis methods. In this work, we use a high‐throughput combinatorial synthesis approach to fabricate lead‐free ferroelectric superlattices and solid solutions of (Ba 0.7 Ca 0.3 )TiO 3 (BCT) and Ba(Zr 0.2 Ti 0.8 )O 3 (BZT) phases with continuous variation of composition and layer thickness. High‐resolution x‐ray diffraction (XRD) and analytical scanning transmission electron microscopy (STEM) demonstrate high film quality and well‐controlled compositional gradients. Ferroelectric and dielectric property measurements identify the “optimal property point” achieved at the composition of 48BZT–52BCT. Displacement vector maps reveal that ferroelectric domain sizes are tunable by varying {BCT–BZT} N superlattice geometry. This high‐throughput synthesis approach can be applied to many other material systems to expedite new materials discovery and properties optimization, allowing for the exploration of a large area of phase space within a single growth. image

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-throughput combinatorial approach expedites the synthesis of a lead-free relaxor ferroelectric system

Developing novel lead-free ferroelectric materials is crucial for next-generation microelectronic technologies that are energy efficient and environment friendly. However, materials discovery and property optimization are typically time-consuming due to the limited throughput of traditional synthesis methods. In this work, we use a high-throughput combinatorial synthesis approach to fabricate lead-free ferroelectric superlattices and solid solutions of (Ba 0.7 Ca 0.3 )TiO 3 (BCT) and Ba(Zr 0.2 Ti 0.8 )O 3 (BZT) phases with continuous variation of composition and layer thickness. High-resolution x-ray diffraction (XRD) and analytical scanning transmission electron microscopy (STEM) demonstrate high film quality and well-controlled compositional gradients. Ferroelectric and dielectric property measurements identify the “optimal property point” achieved at the composition of 48BZT–52BCT. Displacement vector maps reveal that ferroelectric domain sizes are tunable by varying {BCT–BZT} N superlattice geometry. This high-throughput synthesis approach can be applied to many other material systems to expedite new materials discovery and properties optimization, allowing for the exploration of a large area of phase space within a single growth.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structural and electrochemical evolution of alloy interfacial layers in anode-free solid-state batteries

“Anode-free” solid-state batteries feature high energy density since there is no anode active material. Although the beneficial effects of interfacial layers at the anode-solid electrolyte interface have been demonstrated, the mechanisms through which they influence lithium plating/stripping are unclear. Here, in this study, we reveal the evolution of 100-nm silver and gold interfacial layers during lithium plating/stripping using electrochemical methods, electron microscopy, X-ray microcomputed tomography, and modeling. The alloy layers improve Coulombic efficiency and resistance to short circuiting, even though the alloys form solute regions or particulates that detach from the current collector during plating. In situ electrochemical impedance spectroscopy shows that the alloys return to the interface and mitigate contact loss at the end of stripping, avoiding a critical vulnerability of anode-free cells. Contact retention is driven by even Li thickness that promotes spatially uniform stripping, as well as local alloy delithiation in response to current concentrations that homogenizes current and diminishes voiding.

25 ENERGY STORAGE↗
DOE OSTI2023

Near Infrared Plasmonic Properties in Spinel Metal Oxide Nanocrystals [Poster]

Spinel iron oxide nanocrystals are shown to support NIR LSPR. LSPR is dependent on size and Fe 2+ : Fe 3+ ratio and can be tuned to cover telecommunications region via various synthetic controls. Coupling IR emitting QDs with Fe 3 O 4 nanocrystals exhibiting overlapping plasmonic behavior resulted in faster emission. Plasmonic nanocavity optimizes the Purcell effect. Future work aims to integrate Fe 3 O 4 nanocubes into nanogap antenna construction.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Induced Ferromagnetism in Epitaxial Uranium Dioxide Thin Films

Abstract Actinide materials have various applications that range from nuclear energy to quantum computing. Most current efforts have focused on bulk actinide materials. Tuning functional properties by using strain engineering in epitaxial thin films is largely lacking. Using uranium dioxide (UO 2 ) as a model system, in this work, the authors explore strain engineering in actinide epitaxial thin films and investigate the origin of induced ferromagnetism in an antiferromagnet UO 2 . It is found that UO 2+ x thin films are hypostoichiometric ( x <0) with in‐plane tensile strain, while they are hyperstoichiometric ( x >0) with in‐plane compressive strain. Different from strain engineering in non‐actinide oxide thin films, the epitaxial strain in UO 2 is accommodated by point defects such as vacancies and interstitials due to the low formation energy. Both epitaxial strain and strain relaxation induced point defects such as oxygen/uranium vacancies and oxygen/uranium interstitials can distort magnetic structure and result in magnetic moments. This work reveals the correlation among strain, point defects and ferromagnetism in strain engineered UO 2+ x thin films and the results offer new opportunities to understand the influence of coupled order parameters on the emergent properties of many other actinide thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rethinking radiation effects in materials science using the plasma-focused ion beam

This work demonstrates the viability of using a plasma-focused ion beam (PFIB) as a new platform to carry out radiation effects studies in solids. While materials subjected to irradiation in either nuclear reactors or energetic particle accelerators experience limitations with respect to inaccuracies in both flux measurements and lack of precise control of irradiation areas, we demonstrate a new irradiation technique that allows the exposure of a single specimen in multiple areas, at multiple doses, and in site-specific dependencies - all with flux variations on the order of only 1%. This versatile technique also allows materials to be exposed to significantly higher irradiation dose rates than conventional accelerators. To validate the new methodology, we selected the classical example of ion-beam-induced amorphization of pure single-crystal Si. By pioneering the use of the PFIB for radiation effects studies in materials science, we were able to exploit, in both micro- and nanometer-sized detail, the differences in electron image contrast arising from crystalline versus amorphous solid-state phases in classical semiconductors subjected to irradiation, thus providing new insights on amorphization mechanisms. This methodology opens new research frontiers at the fringe of materials science with promising applications beyond the scope of materials at extremes such as in nanopatterning, nanodevices and nanoarchitectonics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Kink mechanism in Cu/Nb nanolaminates explored by $\mathcal{in}$ $\mathcal{situ}$ pillar compression

We report Nano metallic laminates (NMLs) exhibit different failure modes depending on the loading conditions due to their mechanical anisotropies. Kinking is a typical failure mode in many NMLs compressed along a layer-parallel direction. However, a detailed description of the microstructure evolution during kink band (KB) formation and an in-depth understanding of the formation mechanisms are lacking. In this work, the KB process is investigated in Cu/Nb NMLs by in situ micro pillar compression in the scanning electron microscope (SEM) along a layer-parallel direction. Post-mortem S/TEM and transmission Kikuchi diffraction (TKD) analyses show that kink banding leads to significant microstructure changes characterized by an accumulation of geometrically necessary dislocations (GNDs) and of tilt geometrically necessary boundaries (GNBs) near KB boundaries (KBBs). The distinct microstructure evolution implies that KB formation is facilitated by the inhomogeneous microstructures resulting in constrained deformation modes. Specifically, dislocations active on slip planes nearly parallel to the interfaces make a major contribution to kink evolution after the onset of kinking. Once layer-parallel slip systems are activated, preexisting lattice dislocations and dislocations nucleating from interfaces will accumulate as GNDs near KBBs via the stochastic storage of lattice dislocations that have certain Burgers vectors. GNDs can further transform into GNBs via cross-slip and climb driven processes near the KBB. Furthermore, GNBs near KBBs can grow by incorporating more GNDs or by coalescence to accommodate the KB evolution. We further hypothesize that microstructural perturbations and their ensuing stresses can initiate KB formation in Cu/Nb NMLs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural dependence of defect formation in iron-oxide thin films

In this report passivating iron-oxide films are grown atop iron films simulating the corrosion process in a nuclear reactor environment. Two oxide films grown via physical vapor deposition at 600 °C and room temperature exhibited dense-epitactic and columnar-polycrystalline, microstructures respectively. A third oxide film grown in open air at 600 °C exhibited an eqiuaxed, porous morphology. Cubic maghemite and magnetite phases in each oxide film were identified via grazing incidence X-ray diffraction. Positron annihilation spectroscopy was used to characterize point defects and measure their depth and size distributions in each oxide layer and showed a range of average positron lifetimes from 0.23 ns in the high temperature, vapor deposited film, 0.35 ns in the room temperature-grown film, and 0.31 ns in the thermally grown oxide. These data indicate that the film morphology, which varies greatly in these films, leads to very different defect content. Finally, four-dimensional scanning transmission electron microscopy was used to measure the internal stress of each film and was correlated to the strain state presented in the X-ray diffraction spectra. The defect formation in each film is reasoned through using a thin film growth model.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of lattice strain on magnetism in epitaxial YCrO 3 films

The influence of lattice strain on magnetism is studied for perovskite rare-earth chromite, YCrO 3 (YCO) thin films. A combined theoretical and experimental approach is used to demonstrate the correlation between lattice-strain and magnetic properties of YCO films. The first-principles calculations reveal that the local Cr magnetic moments and the out-of-plane magnetization linearly increase with changing the in-plane lattice strain from compressive to tensile. The experimental results agree with the theory findings showing a strong dependence of magnetization on epitaxial strain in YCO films. These results unveil the lattice-strain-controlled functionalities on perovskite rare-earth chromites and related material systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid-State Welding of the Nanostructured Ferritic Alloy 14YWT Using a Capacitive Discharge Resistance Welding Technique

Joining nanostructured ferritic alloys (NFAs) has proved challenging, as the nano-oxides that provide superior strength, creep resistance, and radiation tolerance at high temperatures tend to agglomerate, redistribute, and coarsen during conventional fusion welding. In this study, capacitive discharge resistance welding (CDRW)—a solid-state variant of resistance welding—was used to join end caps and thin-walled cladding tubes of the NFA 14YWT. The resulting solid-state joints were found to be hermetically sealed and were characterized across the weld region using electron microscopy (macroscopic, microscopic, and nanometer scales) and nanoindentation. Microstructural evolution near the weld line was limited to narrow (~50–200 μm) thermo-mechanically affected zones (TMAZs) and to a reduction in pre-existing component textures. Dispersoid populations (i.e., nano-oxides and larger oxide particles) appeared unchanged by all but the highest energy and power CDRW condition, with this extreme producing only minor nano-oxide coarsening (~2 nm → ~5 nm Ø). Despite a minimal microstructural change, the TMAZs were found to be ~10% softer than the surrounding base material. These findings are considered in terms of past solid-state welding (SSW) efforts—cladding applications and NFA-like materials in particular—and in terms of strengthening mechanisms in NFAs and the potential impacts of localized temperature–strain conditions during SSW.

36 MATERIALS SCIENCE↗
DOE OSTI2021

IMS Rapid Response FY21 Summary Report for: Integrating Patterned Probes with Four-Dimensional Scanning Transmission Electron Microscopy for Unrivaled Crystallographic Structure Determination in Nanomaterials

The initial goal of our 4-dimensional scanning transmission electron microscopy (4D-STEM)-based project was to develop strain resolution two orders of magnitude better than what is now currently possible with electron-based scattering techniques, all while collecting scattering information from 7 different tilt axes at one time [multi-beam electron diffraction (MBED)1 ] through the development of a new electron probe-forming aperture with non-circular features (patterned probes 2 ). We set out to accomplish this through a collaboration with Drs. Colin Ophus and Ben Savitsky at Lawrence Berkeley Laboratory (they are the world-leading experts in developing the complex computational codes required to perform orientation analysis and quantitative strain mapping on our 4D-STEM data sets. We are motivated to invest in this area as it will be the only technique sensitive enough to perform three- dimensional automated crystallographic orientation mapping (ACOM) and strain mapping for materials exposed to external stimulus (a focus of our larger efforts).

36 MATERIALS SCIENCE↗
DOE OSTI2021

py4DSTEM: A Software Package for Four-Dimensional Scanning Transmission Electron Microscopy Data Analysis

Scanning transmission electron microscopy (STEM) allows for imaging, diffraction, and spectroscopy of materials on length scales ranging from microns to atoms. By using a high-speed, direct electron detector, it is now possible to record a full two-dimensional (2D) image of the diffracted electron beam at each probe position, typically a 2D grid of probe positions. These 4D-STEM datasets are rich in information, including signatures of the local structure, orientation, deformation, electromagnetic fields, and other sample-dependent properties. However, extracting this information requires complex analysis pipelines that include data wrangling, calibration, analysis, and visualization, all while maintaining robustness against imaging distortions and artifacts. In this paper, we present py4DSTEM, an analysis toolkit for measuring material properties from 4D-STEM datasets, written in the Python language and released with an open-source license. We describe the algorithmic steps for dataset calibration and various 4D-STEM property measurements in detail and present results from several experimental datasets. We also implement a simple and universal file format appropriate for electron microscopy data in py4DSTEM, which uses the open-source HDF5 standard. We hope this tool will benefit the research community and help improve the standards for data and computational methods in electron microscopy, and we invite the community to contribute to this ongoing project.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Intrinsic helical twist and chirality in ultrathin tellurium nanowires

Robust atomic-to-meso-scale chirality is now observed in the one-dimensional form of tellurium. This enables a large and counter-intuitive circular-polarization dependent second harmonic generation response above 0.2 which is not present in two-dimensional tellurium. Orientation variations in 1D tellurium nanowires obtained by four-dimensional scanning transmission electron microscopy (4D-STEM) and their correlation with unconventional non-linear optical properties by second harmonic generation circular dichroism (SHG-CD) uncovers an unexpected circular-polarization dependent SHG response from 1D nanowire bundles – an order-of-magnitude higher than in single-crystal two-dimensional tellurium structures – suggesting the atomic- and meso-scale crystalline structure of the 1D material possesses an inherent chirality not present in its 2D form; and which is strong enough to manifest even in the aggregate non-linear optical (NLO) properties of aggregates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Local Lattice Deformation of Tellurene Grain Boundaries by Four-Dimensional Electron Microscopy

Two-dimensional (2D) tellurene is a promising competitor for the fabrication of ultrathin optoelectronic devices belonging to a new family of monoelemental 2D materials. Furthermore, the precise fabrication and characterization of tellurene and its lattice defects is of utmost importance to determine device reliability and predict functionality, yet it remains experimentally challenging. The rapid growth of the four-dimensional scanning transmission electron microscopy (4D-STEM) technique as well as postprocessing tools now allows for structural analysis with nanometer-scale resolution over a broad range of length scales. Here, we use 4D-STEM to reveal the three-dimensional (3D) atomic structure of the characteristic grain boundary in 2D tellurium formed through a new microwave-enabled chemical self-assembly. Strain and lattice parameter maps permit the reconstruction of the roughness of the grain boundary and suggest that its formation is promoted by a wedge of helical atomic chains along the [0001] crystallographic direction. The observation of wrinkles at the grain boundary is found to be the dominant relaxation mechanism. Insights into the formation mechanism are elucidated by mapping the lattice parameters as the first demonstration of local in-plane and out-of-plane unit cell variation in a nanometer-by-nanometer real-space array.

36 MATERIALS SCIENCE↗