Engineering Papers⌕ Search

Engineering topics

Schieldge, J. P.

Publications and source records attributed to Schieldge, J. P..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Sensitivity of thermal inertia calculations to variations in environmental factors

The sensitivity of thermal inertia (TI) calculations to errors in the measurement or parameterization of a number of environmental factors is considered here. The factors include effects of radiative transfer in the atmosphere, surface albedo and emissivity, variations in surface turbulent heat flux density, cloud cover, vegetative cover, and topography. The error analysis is based upon data from the Heat Capacity Mapping Mission (HCMM) satellite for July 1978 at three separate test sites in the deserts of the western United States. Results show that typical errors in atmospheric radiative transfer, cloud cover, and vegetative cover can individually cause root-mean-square (RMS) errors of about 10 percent (with atmospheric effects sometimes as large as 30-40 percent) in HCMM-derived thermal inertia images of 20,000-200,000 pixels.

Kahle, A. B.↗
NASA NTRS1984

Geologic mapping using thermal images

Thermal radiance data from the Heat Capacity Mapping Mission (HCMM) satellite has been used to measure surface reflectance data and to provide additional material composition information through remote sensing. The primary goal was to investigate the utility of HCMM data for geologic applications. Three techniques were used for displaying and combining thermal and visible near infrared (VNIR) data for two desert areas in southern California (Trona and Pisgah): color additive composites (CAC) for day and night IR and day VNIR, principal components, and calculation of thermal inertia images. The HCMM thermal data were more effective than Landsat data in producing separation of compositionally different areas including volcanic and intrusive rocks. The satellite CAC data produced an image for a 1 x 2 degree area, and the color picture was enlarged to a scale of 1:250,000. Playa composition, moisture content, presence of standing water, and vegetation cover were displayed in a variety of colors according to physical characteristics. Areas such as sand dunes were not distinguishable because of the coarse 500-mm HCMM resolution. HCMM thermal data have shown a new dimension to geologic remote sensing, and future satellite missions should allow the continued development of the thermal infrared data for geology.

Abrams, M. J.↗
NASA NTRS1983

Field Measurement of Thermal Inertia

Radiometric measurements determine thermal inertia for geologic materials. Measurements are correlated with data obtained by remote sensing, for discriminating varieties of rock encountered when exploring for minerals by aircraft or by satellites equipped with infrared scanners.

Kahle, A. B.↗
NASA NTRS1982

Evaluation of thermal data for geologic applications

Sensitivity studies using thermal models indicated sources of errors in the determination of thermal inertia from HCMM data. Apparent thermal inertia, with only simple atmospheric radiance corrections to the measured surface temperature, would be sufficient for most operational requirements for surface thermal inertia. Thermal data does have additional information about the nature of surface material that is not available in visible and near infrared reflectance data. Color composites of daytime temperature, nighttime temperature, and albedo were often more useful than thermal inertia images alone for discrimination of lithologic boundaries. A modeling study, using the annual heating cycle, indicated the feasibility of looking for geologic features buried under as much as a meter of alluvial material. The spatial resolution of HCMM data is a major limiting factor in the usefulness of the data for geologic applications. Future thermal infrared satellite sensors should provide spatial resolution comparable to that of the LANDSAT data.

Kahle, A. B.↗
NASA NTRS1982

Aircraft measurement of sea surface temperature during the West Coast Experiment

During the West Coast Experiment in March 1977, a test was conducted to ascertain the effectiveness of using remote sensing techniques to estimate sea surface temperature (SST) from infrared (IR) emissions of the sea surface. Aircraft flights were made over three buoys moored in southern California coastal waters, and data was collected of sea surface emissions at thermal IR wavelengths (7.95-13.5 micrometers). SST obtained from the remote sensing measurements were compared with in situ SST measured with thermistors mounted on the buoys. The remotely determined SST were from 1.4-2.9 C lower than the in situ measurements. Several factors are discussed that could account for the differences.

Schieldge, J. P.↗
NASA NTRS1982

An instrument for measuring thermal inertia in the field

Features and test results of a thermal inertial meter (TIM) for cataloging the thermal inertial of surface material in situ as a basis for satellite remote sensing of geologic materials are described. The instrument is employed to determine the temperature rise of the materials in the field, with the assumptions that the sample and a standard are homogeneous in composition, the heat flux density is constant at the surface of each material, and the specimens are thick enough to be treated as semi-infinite bodies. A formula for calculating thermal inertia is presented, and the components of the TIM are detailed. A box with three compartments, two holding standards, is placed on the sample surface with the third compartment open to the specimen. Dolomite and quartz are used as references when all samples are measured after heating. Tests with rocks and sand in Nevada and California revealed that chert has a higher thermal inertia than barite.

Marsh, S. E.↗
NASA NTRS1982

A numerical simulation of soil temperature and moisture variations for a bare field

The diurnal variations of soil temperature and moisture content were simulated for a bare agricultural field in the San Joaquin Valley in California. The simulation pertained to the first 72 hours of drying, from saturation, of a sandy, clay loam soil. The results were compared with measurements of soil temperature and moisture content made at the field. Calculated and measured values of soil temperature trends agreed in general, but model results of moisture trends did not replicate observed diurnal effects evident at depths 4 centimeters or more below the surface.

Schieldge, J. P.↗
NASA NTRS1981

Geologic application of thermal inertia imaging using HCMM data

Three test sites in the western US were selected to discriminate among surface geologic materials on the basis of their thermal properties as determined from HCMM data. Attempts to determine quantitatively accurate thermal inertia values from HCMM digital data met with only partial success due to the effects of sensor miscalibrations, radiative transfer in the atmosphere, and varying meteorology and elevation across a scene. In most instances, apparent thermal inertia was found to be an excellent qualitative representation of true thermal inertia. Computer processing of digital day and night HCMM data allowed construction of geologically useful images. At some test sites, more information was provided by data than LANDSAT data. Soil moisture effects and differences in spectrally dark materials were more effectively displayed using the thermal data.

Kahle, A. B.↗
NASA NTRS1981

Anomalous behavior of the atmospheric surface layer over a melting snowpack

During March, 1978 on a snow-covered field near Lee Vining, California, measurements were made that included: (1) variations above the snow surface of the net radiative flux and the profile of wind speed, air temperature and relative humidity; and (2) variations beneath the snow surface of the conductive heat flux and the temperature profile. The period was marked by clear skies, warm air and calm winds during the day, and cold air and moderate winds at night. During the day, a highly stable sublayer formed near the surface, with a persistent warm layer at approximately 0.5 m above the surface. At night, profiles agreed more with classical log-linear forms found in stable air. Numerical simulation of long and shortwave radiative fluxes near the surface, using observed humidity profiles, produced the daytime warm level in agreement with observations. It was concluded that in the absence of turbulent mixing, strong solar radiation and a supply of moisture from the snow will cause a raised maximum of temperature during the day.

Halberstam, I.↗
NASA NTRS1981

Some examples of the utility of HCMM data in geologic remote sensing

Examples of HCMM (Heat Capacity Mapping Mission) data in geologic remote sensing are presented, and the data set is composed of HCMM and aircraft digital scanner data and ground truth data from four western U.S. test sites. Data are used in the thermal model to test thermal data effectiveness, and changes in temperature with depth and time for dry soils are described by the model. It is found that the HCMM thermal inertia image is useful in the separability of bedrock and alluvium in Death Valley, and aa and pahoehoe flows in the Pisgah basalt flow. In a color composite of HCMM day temperature, night temperature, and day visible images of the Pisgah Crater test site, it is possible to distinguish alluvium, playa, aa and pahoehoe basalt flow, rhyolite intrusives, and other elements. Ground checking of units at a few points will extend capabilities to large areas and assist in creating telegeologic maps.

Kahle, A. B.↗
NASA NTRS1980

Joint microwave and infrared studies for soil moisture determination

The feasibility of using a combined microwave-thermal infrared system to determine soil moisture content is addressed. Of particular concern are bare soils. The theoretical basis for microwave emission from soils and the transport of heat and moisture in soils is presented. Also, a description is given of the results of two field experiments held during vernal months in the San Joaquin Valley of California.

Njoku, E. G.↗
NASA NTRS1980

Use of thermal-inertia properties for material identification

It is noted that a knowledge of the thermal inertia of the earth's surface can be used in geologic mapping as a complement to surface reflectance data as provided by Landsat. Thermal inertia, which is a body property, cannot be determined directly but can be inferred from radiation temperature measurements made at various times in the diurnal heating cycle, combined with a model of the surface heating processes. A model of this type is developed and applied along with temperature measurements made in the field and by satellite to determine thermal properties of surface materials. An example from a test site in western Nevada is used to demonstrate the utility of this technique.

Schieldge, J. P.↗