Engineering topics
Publications and source records attributed to Scheiman, J..
A single axis, five beam, three component laser velocimeter system was used in a juncture flow experiment. A description of the seeding system developed for and used in this experiment is given. The performanace of the LV system was evaluated, and some of the problems associated with it were identified. Satisfactory results were obtained in the juncture flow experiments using this LV system.
A Laser Velocimetry (LV) seeding system was specifically developed for the Langley Low Turbulence Wind Tunnel (LTPT), and it has been successfully used for LV measurements in two major tests (Juncture Flow Experiment and Gortler Experiment). The LTPT is capable of operating at Mach numbers from 0.05 to 0.50 and unit Reynolds numbers from 100,000 to 15,000,000 per foot. The test section is 3 feet wide and 7.5 feet high. The turbulence level in the test section is relatively low because of the high contraction ratio and because of the nine turbulence reduction screens in the settling chamber. A primary requirement of the seeding system was that the seeding material not contaminate or damage in any way these screens. Both solid and liquid seeding systems were evaluated, and the results are presented. They can provide some guidelines for setting up seeding systems in other similar tunnels.
The turbulent flow in a simulated wing-fuselage juncture has been investigated using Laser Velocimetry. The juncture was simulated by a splitter plate with an unswept wing model mounted perpendicular to it. The use of sharp wing leading edge results in the elimination of separation ahead of leading edge, and hence the separation vortex. Secondary flow induced by Reynolds stress gradients is the main source of vortical motion in the juncture formed by the plate and the flat surface of the wing, whereas in the juncture formed by the plate and the circular arc surface of the wing, streamwise vorticity is generated because of the presence of lateral curvature in the flow field. The results of this study indicate that fillets in the juncture can improve the flow characteristics near the wing trailing edge.
Calibration tests using hot wires were conducted using a newly developed test rig that greatly reduced the data acquisition time. A comparison of measured and computed velocity vector magnitude and direction indicates the necessity of complete probe calibration to determine flow interference and/or operating limitation regions. Calibration results indicate that flow rates with 3 percent accuracy and flow angles with 5 deg accuracy are attainable.
Turbulence reduction research using screens, honeycomb, and combinations thereof was conducted in a half-scale model of a portion of the Langley 8-foot transonic pressure tunnel. It was found that screens alone reduce axial turbulence more than lateral turbulence; whereas, honeycomb alone reduces laterial turbulence more than axial turbulence. Because of this difference, the physical mechanism for decreasing turbulence for screens and honeycomb must be completely different. It is concluded that honeycomb with a downstream screen is an excellent combination for reducing turbulences.
Tests were conducted on a half-scale model representing a 0.914-m (3.0-ft) square stream tube of the flow through the fourth corner and settling chamber of the Langley 8-Foot Transonic Pressure Tunnel. The model included the tube cooler 45 degree turning vanes, and the turbulence reduction screens and honeycomb, which were the subject of the tests. Hot-wire measurements of the turbulence reduction for various combinations of screens and honeycomb were made at various duct speeds. Of the four sizes of honeycomb cells tested, none were found to have a superior performance advantage. The effectiveness of screens and honeycomb in reducing turbulence is greatly affected by relatively minor physical damage; therefore, extreme care must be exercised in installing and maintaining honeycomb or screens if the turbulence reduction performance is to be maintained.
The device test model consisted of a cooler, turning vanes, and settling chamber (immediately upstream of the contraction) in which various combinations of screens and honeycomb were tested. Conventional hot wires were used to measure the axial and lateral turbulence reduction for the different turbulence reduction devices. The final configuration chosen consisted of a honeycomb followed by five screens.
A 1/2-scale model of a portion of the NASA Langley 8-foot transonic pressure tunnel was used to conduct some turbulence reduction research. The experimental results are correlated with various theories. Screens alone reduce axial turbulence more than the lateral turbulence; whereas, honeycomb alone reduce lateral turbulence more than axial turbulence. Because of this difference, the physical mechanism for decreasing turbulence for screens and honeycomb must be completely different. Honeycomb with a downstream screen is an excellent combination for reducing turbulence.
Split-film vector anemometer accurately measures magnitude and direction of fluid flow velocity in three-dimensional space using only one of three split films in three-prong split-film system. With procedure, one sensor develops all data previously required by three.
Acoustic measurements were made with inside and far-field microphones. Correlation of measured frequencies with available theories indicates that existing theories are applicable over a broader range than previously shown. The cavity configuration with a partial covering downstream amplified tonal intensities. The frequency of the tones depended on cavity size, not on cavity open area. Introducing upstream disturbances decreased the amplitude of the cavity tones.
Based on exploratory acoustic measurements in Langley's V/STOL wind tunnel, recommendations are made on the methodology for making sound power measurements of aircraft components in the closed tunnel test section. During airflow, tunnel self-noise and microphone flow-induced noise place restrictions on the amplitude and spectrum of the sound source to be measured. Models of aircraft components with high sound level sources, such as thrust engines and powered lift systems, seem likely candidates for acoustic testing.
An experimental investigation has been conducted to investigate the broadband noise generated by a rotating-blade system. Tests were made with circular and NACA 0012 rotor-blade sections. The blades were operated only with zero lift at each radial station. Tests were made both with zero axial velocity, so that the blades operated in their own turbulent wake, and with a small axial velocity imposed by the wind tunnel to blow the wake of one blade away before the passage of the next blade. The rotor with cylindrical blades generally radiated more noise throughout the noise spectrum than did the rotor with airfoil blades. Blowing the blade wake away from the rotor with cylindrical blades did not have any appreciable effect on the amplitude frequency spectrum, and the predominant noise was broadband, either with tunnel wind on or off. For the rotor with airfoil blades, however, blowing the blade wake away changed the character of the noise spectrum completely in that broadband noise was eliminated or diminished to such an extent as to be indistinguishable. The broadband noise of the airfoil-bladed rotor with zero axial velocity is apparently caused by lift fluctuations due to velocity components of the turbulence normal to the plane of rotation.
An experimental investigation has been made of the Langley full-scale tunnel and outdoors to investigate some of the characteristics of vortex noise generated on a rotating-blade system. Acoustic measurements were made at several microphone positions for two different blade sections with several tip shapes and spoiler configurations. The blades were operated only at zero lift at each radial station, both for operating in their own wake and for operating with the wake blown downstream. Rotors with cylindrical blades generally created more noise throughout the noise spectrum than the rotor with NACA 0012 blades. Blowing the shed wake from the rotor with cylindrical blades did not have an appreciable effect on the frequency-amplitude spectrum. The tip shape changes had very little effect on the frequency-amplitude spectrum of the noise. Spoilers applied to the rotor with NACA 0012 blades increased the amplitude of the spectrum and decreased the number of harmonics of blade passage frequency.
An investigation was conducted in the Langley full-scale tunnel to study some factors affecting the tip vortex of a wing. It was found that there was a pronounced effect of Reynolds number on the tip-vortex core size. An attempt was made to determine what aerodynamic parameters, such as lift, drag, or induced drag, influence the size of the vortex core, but no particular function of the parameters was found to be superior to all others. Various spoilers placed on the upper and lower surfaces of the wing to increase the boundary-layer thickness resulted in a reduction in the vorticity as determined from the tuft grid. Various solid objects placed in the vortex core downstream of the wing tip seemed to decrease the vorticity within the vortex core.
Acoustical measurements of vortex noise for rotating blade with and without shed wake blown downstream - tables
Wind tunnel investigation of tip vortex structure of semispan wing for several wing-tip modifications
Helicopter rotor blade pressure distributions compared with static two-dimensional airfoil characteristics for extreme flight conditions
Helicopter rotor blade chordwise pressure distribution and two-dimensional airfoil characteristics