Engineering Papers⌕ Search

Engineering topics

Sawada, H.

Publications and source records attributed to Sawada, H..

At least 19 records

Characterization of sub-picosecond laser-produced fast electrons by modeling angularly resolved bremsstrahlung measurements with 3D hybrid particle-in-cell code

Hard x-rays produced by intense laser-produced fast electrons interacting with solids are a vital source for producing radiographs of high-density objects and implosion cores for inertial confinement fusion. Accurate calculation of hard x-ray sources requires a three-dimensional (3D) simulation geometry that fully models the electron transport dynamics, including electron recirculation and the generation of absolute photon yields. To date, 3D simulations of laser-produced bremsstrahlung photons over tens of picoseconds and code benchmarking have not been performed definitively. In this study, we characterize sub-picosecond laser-produced fast electrons by modeling angularly resolved bremsstrahlung measurements for refluxing and non-refluxing targets using the 3D hybrid particle-in-cell (PIC), Large Scale Plasma code. Bremsstrahlung radiation and escaped electron data were obtained by focusing a 50-TW Leopard laser (15 J, 0.35 ps, 2 × 10 19 W/cm 2 ) on a 100-μm-thick Cu foil and a Cu with a large plastic backing (Cu–CH target). Data for both the Cu and Cu–CH targets were reproduced for simulations with a given set of electron parameters. Comparison of the simulations revealed that the hard x-ray emission from the Cu target was significantly longer in duration than that from the Cu–CH target. Here, the benchmarked hybrid PIC code could prove to be a powerful tool in the design and optimization of time- and angular-dependent bremsstrahlung sources for flash x-ray and gamma-ray radiography.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

2D monochromatic x-ray imaging for beam monitoring of an x-ray free electron laser and a high-power femtosecond laser

Single-shot simultaneous beam monitoring of an x-ray free electron laser (XFEL) and a high-power femtosecond laser is demonstrated using 2D monochromatic Kα imaging. In a pump-probe experiment carried out at the Matter in Extreme Conditions end-station of the Linac Coherent Light Source, a thin solid titanium foil irradiated by a 25-TW relativistic intensity laser for fast electron isochoric heating was probed by a 7.0 keV XFEL beam for x-ray Thomson scattering measurements. Using a spherical crystal imager (SCI), the spatial overlap of the beams was examined by measuring 4.5 keV titanium Kα x rays produced by laseraccelerated fast electrons and the x-ray beam. Changes in XFEL-induced Kα emission patterns were observed down to a ~20×40 μm2 rectangular shape as the beam was focused. Laser-only and two-beam shots reveal that large spatial offsets of laser-induced Kα spots in a horizontal direction is attributed to imprecise target positioning rather than shot-to-shot laser pointing variations. As a consequence, successful beam overlapping was observed on ~58% of all two-beam shots for 10 μm thick samples. The Kα measurements also show a linear relationship between total Kα yields and integrated x-ray scattering signals. Monochromatic xray imaging with SCI could be used as an on-shot beam pointing diagnostic in XFEL-laser or multiple short-pulse laser experiments.

47 OTHER INSTRUMENTATION↗

The response function of Fujifilm BAS-TR imaging plates to laser-accelerated titanium ions

Calibrated diagnostics for energetic particle detection allow for the systematic study of charged particle sources. The Fujifilm BAS-TR imaging plate (IP) is a reusable phosphorescent detector for radiation applications such as x-ray and particle beam detection. The BAS-TR IP has been absolutely calibrated to many low-Z (low proton number) ions, and extending these calibrations to the mid-Z regime is beneficial for the study of laser-driven ion sources. The Texas Petawatt Laser was used to generate energetic ions from a 100 nm titanium foil, and charge states Ti 10+ through Ti 12+ , ranging from 6 to 27 MeV, were analyzed for calibration. A plastic detector of CR-39 with evenly placed slots was mounted in front of the IP to count the number of ions that correspond with the IP levels of photo-stimulated luminescence (PSL). Here, a response curve was fitted to the data, yielding a model of the PSL signal vs ion energy. Comparisons to other published response curves are also presented, illustrating the trend of PSL/nucleon decreasing with increasing ion mass.

47 OTHER INSTRUMENTATION↗

Development of broadband x-ray radiography for diagnosing magnetically driven cylindrically compressed matter

Experiments and modeling of x-ray radiography of millimeter diameter solid Al wires with laser-produced broadband x rays are reported. Experiments were performed using the 50-TW Leopard short-pulse laser in a laser and pulsed power chamber at the Nevada Terawatt Facility. To characterize broadband x rays and demonstrate a radiographic capability, bremsstrahlung, escaping electrons, and radiograph images of Al wires were simultaneously measured. The angularly resolved x-ray spectra are modeled by comparing measured bremsstrahlung signals in the range between 10 and ~500 keV with hybrid particle-in-cell simulations. Transmission of Al wires from the radiograph images is further simulated with a Monte Carlo code. The measured transmission profiles of Al wires with three different diameters agree with calculations when a simulated x-ray spectrum composed of line emissions and bremsstrahlung is used with a source size of 600 ± 200 μm. Transmission calculations with only 22 keV Ag Kα or an exponential x-ray spectrum do not reproduce the measurement, suggesting that the accurate determination of an x-ray source spectrum, as well as the inclusion of the photon sensitivity of the detector, is critical in transmission calculations to infer the density of an object. As a result, the laser-based broadband x-ray radiography that was developed has been successfully implemented in a pulsed power chamber for future laser-pulsed-power coupled experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of laser produced plasma in a longitudinal magnetic field

In this work, laser produced plasma embedded in a longitudinal magnetic field was studied using a 1 MA pulsed power generator coupled with a 50 TW laser. Half turn coil loads with an internal diameter of 2.5–3.5 mm generate a 50–70 T axial magnetic field near the load. A subpicosecond laser pulse with an intensity of 10 18 –10 19 W/cm 2 irradiates a thin Si foil target in the magnetic field of the coil load. A laser produced plasma plume collimates within the longitudinal field to a narrow jet 0.2–0.3 mm in diameter with a length of 3–4 mm and an electron plasma density of (0.2–1) × 10 20 cm ₋3 on the jet axis. The jet propagates with a velocity of 160–200 km/s in general agreement with magnetohydrodynamic simulations. X-ray spectral measurements demonstrate an increase in the plasma electron density resulting from the magnetic confinement of the jet.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Monochromatic 2D K α Emission Images Revealing Short-Pulse Laser Isochoric Heating Mechanism

The rapid heating of a thin titanium foil by a high intensity, subpicosecond laser is studied by using a 2D narrow-band x-ray imaging and x-ray spectroscopy. Here, a novel monochromatic imaging diagnostic tuned to 4.51 keV Ti Kα was used to successfully visualize a significantly ionized area ( < Z > >17±1) of the solid density plasma to be within a ~35 μm diameter spot in the transverse direction and 2 μm in depth. The measurements and a 2D collisional particle-in-cell simulation reveal that, in the fast isochoric heating of solid foil by an intense laser light, such a high ionization state in solid titanium is achieved by thermal diffusion from the hot preplasma in a few picoseconds after the pulse ends. The shift of Kα and formation of a missing Kα cannot be explained with the present atomic physics model. The measured Kα image is reproduced only when a phenomenological model for the Kα shift with a threshold ionization of < Z > =17 is included. This work reveals how the ionization state and electron temperature of the isochorically heated nonequilibrium plasma are independently increased.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterization of fast electron divergence and energy spectrum from modeling of angularly resolved bremsstrahlung measurements

Characteristics of fast electrons generated in an intense laser-solid target interaction are studied by modeling angularly resolved bremsstrahlung measurements with a hybrid Particle-In-Cell code, Large Scale Plasmas. The experiment was enacted using the 50 TW Leopard laser at the Nevada Terawatt Facility. A 100 μm thick Cu foil was irradiated by the 15 J, 0.35 ps laser at a peak laser intensity of 2 × 10 19 W/cm 2 . Bremsstrahlung produced by transport and recirculation of the fast electrons in the foil was measured with two differential filter-stack x-ray spectrometers at 22° and 40° from the laser axis. The two-spectrometer signals simultaneously fit by varying single slope temperatures (T hot ) and divergence angles (θ) enable for determining T hot and θ to be 1.1 ± 0.3 MeV and 15° ± 8°, respectively. The T hot inferred from the bremsstrahlung signals agrees with that from an escaped electron measurement, implying that that the bremsstrahlung is predominantly produced by the transport of the high energy fast electrons in the first pass.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduced fast electron transport in shock-heated plasma in multilayer targets due to self-generated magnetic fields

Fast electron transport has been studied in cold solid density CH, cold CH foam (200 mg / cm 3 ), and CH plasma (40 eV 30 mg/cm 3 ) targets—the latter created by shocking the CH foam with a 1.2 kJ long pulse laser and allowing it to expand. The fast electrons were produced using the OMEGA EP laser pulse (800 J, 8 ps) incident on a Au flat target. With the CH plasma, the fluence of fast electrons reaching a Cu foil at the far side of the transport was reduced significantly (25 × weaker peak K $α$ emission). Particle-in-cell simulations using the osiris code modeled fast electron transport in the unshocked foam and plasma cases assuming fixed ionization and including source generation, transport in Au and CH layers, Coulomb collisions, and refluxing. Simulations indicate two main mechanisms which alter electron energy transport through the target between the foam and plasma cases, both due to the magnetic field: a collimating field in the CH region, caused by the resistivity of the return current and more prevalent in the foam; and an insulating field at the Au-CH interface, present only with the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Transport and spatial energy deposition of relativistic electrons in copper-doped fast ignition plasmas

Fast electron transport and spatial energy deposition are investigated in integrated cone-guided Fast Ignition experiments by measuring fast electron induced copper K-shell emission using a copper tracer added to deuterated plastic shells with a geometrically reentrant gold cone. Experiments were carried out at the Laboratory for Laser Energetics on the OMEGA/OMEGA-EP Laser where the plastic shells were imploded using 54 of the 60 OMEGA60 beams (3ω, 20 kJ), while the high intensity OMEGA-EP (BL2) beam (1 ω, 10 ps, 500 J, I peak > 10 19 W/cm 2 ) was focused onto the inner cone tip. Here, a retrograde analysis using the hybrid-PIC electron transport code, ZUMA, is performed to examine the sensitivity of the copper Kα spatial profile on the laser-produced fast electrons, facilitating the optimization of new target point designs and laser configurations to improve the compressed core areal density by a factor of 4 and the fast electron energy coupling by a factor of 3.5.

42 ENGINEERING↗

Two-color monochromatic x-ray imaging with a single short-pulse laser

Here, simultaneous monochromatic crystal imaging at 4.5 and 8.0 keV with x-rays produced by a single short-pulse laser is presented. A layered target consisting of thin foils of titanium and copper glued together is irradiated by the 50 TW Leopard short-pulse laser housed at the Nevada Terawatt Facility. Laser-accelerated MeV fast electrons transmitting through the target induce Kα fluorescence from both foils. Two energy-selective curved crystals in the imaging diagnostic form separate monochromatic images on a single imaging detector. The experiment demonstrates simultaneous two-color monochromatic imaging of the foils on a single detector as well as Kα x-ray production at two different photon energies with a single laser beam. Lastly, application of the diagnostic technique to x-ray radiography of a high density plasma is also presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Collimated Propagation of Fast Electron Beams Accelerated by High-Contrast Laser Pulses in Highly Resistive Shocked Carbon

In this study, collimated transport of ultrahigh intensity electron current was observed in cold and in laser-shocked vitreous carbon, in agreement with simulation predictions. The fast electron beams were created by coupling high-intensity and high-contrast laser pulses onto copper-coated cones drilled into the carbon samples. The guiding mechanism—observed only for times before the shock breakout at the inner cone tip—is due to self-generated resistive magnetic fields of ~ 0.5–1 kT arising from the intense currents of fast electrons in vitreous carbon, by virtue of its specific high resistivity over the range of explored background temperatures. The spatial distribution of the electron beams, injected through the samples at different stages of compression, was characterized by side-on imaging of hard x-ray fluorescence.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Calibration and characterization of a highly efficient spectrometer in von Hamos geometry for 7-10 keV x-rays

Here, we have built an absolutely calibrated, highly efficient, Bragg crystal spectrometer in von Hamos geometry. This zinc von Hamos spectrometer uses a crystal made from highly oriented pyrolytic graphite that is cylindrically bent along the non-dispersive axis. It is tuned to measure x-ray spectra in the 7–10 keV range and has been designed to be used on a Ten Inch Manipulator for the Omega and OmegaEP target chambers at the Laboratory for Laser Energetics in Rochester, USA. Significant shielding strategies and fluorescence mitigation have been implemented in addition to an imaging plate detector making it well suited for experiments in high-intensity environments. Here we present the design and absolute calibration as well as mosaicity and integrated reflectivity measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spectral tomographic analysis of Bremsstrahlung X-rays generated in a laser-produced plasma

A new approach is proposed to analyze Bremsstrahlung X-rays that are emitted from laser-produced plasmas (LPP) and are measured by a stack type spectrometer. This new method is based on a spectral tomographic reconstruction concept with the variational principle for optimization, without referring to the electron energy distribution of a plasma. This approach is applied to the analysis of some experimental data obtained at a few major laser facilities to demonstrate the applicability of the method. Furthermore, slope temperatures of X-rays from LPP are determined with a two-temperature model, showing different spectral characteristics of X-rays depending on laser properties used in the experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Flash Kα radiography of laser-driven solid sphere compression for fast ignition

Time-resolved compression of a laser-driven solid deuterated plastic sphere with a cone was measured with flash Kα x-ray radiography. A spherically converging shockwave launched by nanosecond GEKKO XII beams was used for compression while a flash of 4.51 keV Ti Kα x-ray backlighter was produced by a high-intensity, picosecond laser LFEX (Laser for Fast ignition EXperiment) near peak compression for radiography. Areal densities of the compressed core were inferred from two-dimensional backlit x-ray images recorded with a narrow-band spherical crystal imager. The maximum areal density in the experiment was estimated to be 87 ± 26 mg/cm{sup 2}. The temporal evolution of the experimental and simulated areal densities with a 2-D radiation-hydrodynamics code is in good agreement.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dose-dependent high-resolution electron ptychography

Recent reports of electron ptychography at atomic resolution have ushered in a new era of coherent diffractive imaging in the context of electron microscopy. We report and discuss electron ptychography under variable electron dose conditions, exploring the prospects of an approach which has considerable potential for imaging where low dose is needed.

60 APPLIED LIFE SCIENCES↗

Study of laser-driven cone-in-shell implosion with picosecond monochromatic x-ray radiography on OMEGA

Fuel assembly of a laser-driven cone-in-shell target was studied using picosecond monochromatic x-ray radiography and two-dimensional radiation-hydrodynamics simulation for Fast Ignition (FI) laser fusion. A deuterated plastic shell with a re-entrant Au cone was used as a standard cone-in-shell target in fast ignition heating experiments on OMEGA [W. Theobald et al., Phys. Plasmas 18, 056305 (2011)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Visualizing fast electron energy transport into laser-compressed high-density fast-ignition targets

Understanding of fast electron generation inside the cone and their subsequent transport into hot dense plasmas is crucial to the success of the cone guided fast ignition (FI) scheme of inertial confinement fusion. In our prior work, we developed a new platform that measured, for the first time, the spatial map of fast electron transport in the vicinity of the core of an imploded shell in joint OMEGA and OMEGA EP experiments. In this University of California San Diego-led NLUF project we are using the same platform to investigate several methods of improving coupling efficiency into an imploded CH/CD shell attached to a re-entrant gold cone targets. The shell has an outer diameter of 870 µm consisting of a 15 µm thick outer CH ablator and a 23 µm thick inner CD layer. A Cu dopant (at ~ 1% atomic number density of CD) is added to the CD layer of the shell, which allows characterization of fast electrons transport via their induced Cu K-shell fluorescence radiation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-contrast laser acceleration of relativistic electrons in solid cone-wire targets

Optimization of electron coupling into small solid angles is of extreme importance to applications, such as Fast Ignition, that require maximum electron energy deposition within a small volume. To optimize this coupling, we use the ultra-high-contrast Trident laser, which remains below intensity of 10 11 W/cm 2 until < 0.1 ns before the main pulse, while still attaining high-energy, 75 J, and peak intensity of 5 x 10 19 W/cm 2 . Using a cone-wire target, we find that the coupling into the 40 μm diameter wire is increased by a factor of 2.7x over the low-contrast Titan laser at similar peak intensity. Full-scale simulations are used to model the laser interaction and quantitatively reproduce the experimental results. These show that increase in coupling is due to both a closer interaction, as well as the reduction of laser filamentation and self-focusing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗