Engineering Papers⌕ Search

Engineering topics

Samuelsen, G. S.

Publications and source records attributed to Samuelsen, G. S..

36 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Optimization of circular orifice jets mixing into a heated crossflow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗
NASA NTRS1993

Emission characteristics of a model gas turbine combustor at practical conditions

This paper reports on in situ and exit plane emissions measurements from a model gas turbine combustor at practical air preheat temperatures and pressures for a range of operating conditions. The model combustor chosen for the study features two rows of jets (primary and dilution) with four jets per row, and utilizes effusive air cooling holes on the liner wall. The combustor dome is equipped with a flat-vaned swirler with a vane angle of 60 deg. Data are obtained at combustor pressures ranging from 2 to 10 atmospheres, air preheat temperatures from 204 C to 427 C, and combustor reference velocities from 10.0 to 20.0 m/s. An overall equivalence ratio of 0.3 was constant for all conditions. Exit plane and in situ measurements are presented for HC, O2, CO2, CO, and NO(x). The results from exit plane NO(x) measurements illustrate that the model combustor is representative of current gas turbine combustors. The in situ data reveal effects of fuel/air and wall jet mixing on emission performance.

Drennan, S. A.↗
NASA NTRS1992

Mixing in the dome region of a staged gas turbine combustor

To lower NO(x) emissions from gas-turbine engines the effect of dome design and operational changes on the mixing quality in the fuel-rich region is studied. A statistical analysis is employed to establish the parametric sensitivity in this complex flow. A mixing-effectiveness index is defined and used to optimize the gas-species uniformity and the extent of reaction at the exit plane of the dome. Mixing effectiveness is tied to the fuel and air injection locations, the macroscale structure of the dome aerodynamics, and the level of turbulence. Increases in nozzle/air to fuel ratio, reference velocities, and the dome expansion angle increased the level of turbulence. The optimum configuration featured counter-swirling fuel and air streams and produced a strong torroidal recirculation zone, an effective spray angle of 45 degrees, and azimuthal velocities that decayed to zero inside of two duct diameters. The results underscore the system specific nature of mixing optimization.

Sowa, W. A.↗
NASA NTRS1992

Jet mixing into a heated cross flow in a cylindrical duct: Influence of geometry and flow variations

To examine the mixing characteristics of jets in an axi-symmetric can geometry, temperature measurements were obtained downstream of a row of cold jets injected into a heated cross stream. Parametric, non-reacting experiments were conducted to determine the influence of geometry and flow variations on mixing patterns in a cylindrical configuration. Results show that jet to mainstream momentum flux ratio and orifice geometry significantly impact the mixing characteristics of jets in a can geometry. For a fixed number of orifices, the coupling between momentum flux ratio and injector determines (1) the degree of jet penetration at the injection plane, and (2) the extent of circumferential mixing downstream of the injection plane. The results also show that, at a fixed momentum flux ratio, jet penetration decreases with (1) an increase in slanted slot aspect ratio, and (2) an increase in the angle of the slots with respect to the mainstream direction.

Hatch, M. S.↗
NASA NTRS1991

Calculations of particle-laden flows by second-moment closures

A differential second-moment closure is applied to calculate nonswirling turbulent particle-laden jet flow. The closure is effected by extending constant-density single-phase turbulence models to the continuous (carrier) phase of two-phase flow. The dispersed (discrete) phase is treated by stochastic-Lagrangian technique. To reduce the effects of numerical (false) diffusion on the predicted results, a higher order differencing scheme, namely the flux-spline, is employed. In addition, an experimental study is conducted to provide data of good quality, especially near the inlet, for model assessment. The experiment consists of a confined coaxial jet flow of air with glass beads. The beads' diameter is 105 microns and is injected from the inner jet with a mass loading ratio of 0.9. The computed results are in good agreement with experimental data, especially for the carrier phase. However, the predicted turbulence fluctuations associated with the discrete phase are lower than the data at the downstream region of the flow field.

Nikjooy, M.↗
NASA NTRS1990

Symmetry assessment of an air-blast atomizer spray

This study represents an evaluation of the extent to which conventional and recently introduced modern diagnostics can assess the symmetry of sprays formed by three atomizers of identical design. The conventional diagnostics include sheet-lit photography, patternation, and laser diffraction. The modern diagnostic is laser interferometry (phase Doppler). Symmetry is assessed in ambient conditions for four atomizer orientations, and comparisons are made between the diagnostic techniques. The results demonstrate that conventional and modern diagnostics are consistent in the assessment of symmetry, patternation and phase Doppler are most effective in establishing symmetry of mass flux, and phase Doppler, although more tedious to employ, provides the additional information necessary to establish the sources of detected asymmetries in terms of nonuniformities in droplet velocities, size distributions, volume flux, and concentration.

Mcdonnell, V. G.↗
NASA NTRS1990

An experimental and numerical study of particle-laden coaxial jet flows

A detailed experimental and numerical study of the developing region of coaxial jet flows with and without glass beads is performed. A two-component phase/Doppler interferometer is used to measure mean and fluctuating velocity components for each phase and particle-number density. The numerical calculation is based on a stochastic Lagrangian treatment for the particles and a recently proposed two-equation turbulence model for two-phase flows. Results show that the particle-number density profile becomes narrower than the corresponding profile for round jet flow and that the particles attain a uniform velocity across the jet radius. The particles attenuate the level of gas turbulence and increase their anisotropy level. The numerical calculations yield reasonable and encouraging agreement with the measurements.

Mostafa, A. A.↗
NASA NTRS1990

Influence of the continuous and dispersed phases on the symmetry of a gas turbine air-blast atomizer

Current trends in liquid-fueled practical combustion systems are leaving less tolerance for fuel injection deficiencies such as poor spray field symmetry. The present paper evaluates the symmetry of the flowfield produced by a practical airblast atomizer. Specifically, the influence of both the continuous phase and dispersed phase on the spray field symmetry is assessed. In the present case, asymmetry in volume flux is associated principally with disparities in the injection of the dispersed phase, which is manifested by a maldistribution of larger drops. Asymmetries observed in the continuous phase without the dispersed phase are reduced in magnitude by the presence of the dispersed phase, but still contribute to asymmetry in radial spread of the dispersed phase.

Mcdonell, V. G.↗
NASA NTRS1989

A numerical and experimental study of coaxial jets

An algebraic stress model and the standard k-epsilon model is applied to predict the mean and turbulence quantities for axisymmetric, nonswirling coaxial jets without confinement. To investigate the effects of numerical (false) diffusion on the predicted results, three different discretization schemes, namely, hybrid, power-law, and the flux-spline, are employed. In addition, an experimental study is conducted to provide data of good quality, especially near the inlet, for model assessment. The results show that the use of the algebraic stress model leads to better agreement between the numerical results and experimental data.

Nikjooy, M.↗
NASA NTRS1989

A numerical and experimental study of confined swirling jets

A numerical and experimental study of a confined strong swirling flow is presented. Detailed velocity measurements are made using a two-component laser Doppler velocimeter (LDV) technique. Computations are performed using a differential second-moment (DSM) closure. The effect of inlet dissipation rate on calculated mean and turbulence fields is investigated. Various model constants are employed in the pressure-strain model to demonstrate their influences on the predicted results. Finally, comparison of the DSM calculations with the algebraic second-monent (ASM) closure results shows that the DSM is better suited for complex swirling flow analysis.

Nikjooy, M.↗
NASA NTRS1989

Application of two-component phase Doppler interferometry to the measurement of particle size, mass flux, and velocities in two-phase flows

Two-component phase Doppler interferometry is described, along with its application for the spatially-resolved measurements of particle size, velocity, and mass flux as well as continuous phase velocity. This technique measures single particle events at a point in the flow; droplet size is deduced from the spatial phase shift of the Doppler signal. Particle size influence and discrimination of continuous and discrete phases are among issues covered. Applications are presented for four cases: an example of the discrimination of two sizes of glass beads in a jet flow; a demonstration of the discrimination of phases in a spray field; an assessment of atomizer symmetry with respect to fuel distribution; and a characterization of a droplet field in a reacting spray. It is noted that the above technique is especially powerful in delineating droplet interactions in the swirling, complex flows typical of realistic systems.

Mcdonell, V. G.↗
NASA NTRS1989

Holographic diagnostics of breakup phenomena of impinging jets for liquid rocket motor applications

The use of pulsed laser holography in analyzing the atomization of impinging jets is evaluated using a holographic camera system capable of recording a 3D image of the atomization process in 3 x 10 exp -8 seconds. The holocamera and the experimental configuration and procedure are described in detail. Two nozzles were fabricated to produce 1-mm diameter liquid water jets that impinged at 60 and 90 deg. Holograms were obtained for each nozzle at liquid velocities of 20 and 40 m/s. Analysis of the holograms revealed the evolution of the jets from the plane of emergence through the region of droplet formation. Features of interest included the growth of disturbances prior to the breakup region and the effect of these disturbances on the formation of ligaments and liquid globules. Preliminary analyses show that waves of atomized liquid formed after impingement are closely correlated to waves measured on the jets, leading to the possibility of controlling the atomization process at the nozzle.

Hess, C. F.↗
NASA NTRS1988

K-epsilon turbulence model assessment with reduced numerical diffusion for coaxial jets

A numerical study has been conducted to evaluate the performance of the k-epsilon turbulence model for axisymmetric, unconfined, swirling, and nonswirling coaxial jet flows. Two lower order schemes, hybrid and power-law, and two higher order schemes, flux-spline and bounded skew upwind differencing, were employed in this investigation. The predicted results indicate that the higher order numerical schemes have greater potential for future model improvements and complex flow calculations in terms of storage, accuracy, and execution time. For the nonswirling flow, computations using an algebraic stress model have also been presented.

Nikjooy, M.↗
NASA NTRS1986

Aerothermal modeling program, phase 2. Element C: Fuel injector-air swirl characterization

The main objectives of the NASA-sponsored Aerothermal Modeling Program, Phase 2--Element C, are experimental evaluation of the air swirler interaction with a fuel injector in a simulated combustor chamber, assessment of the current two-phase models, and verification of the improved spray evaporation/dispersion models. This experimental and numerical program consists of five major tasks. Brief descriptions of the five tasks are given.

Mostafa, A. A.↗
NASA NTRS1985

Aerothermal modeling program, phase 2

The main objectives of the Aerothermal Modeling Program, Phase 2 are: to develop an improved numerical scheme for incorporation in a 3-D combustor flow model; to conduct a benchmark quality experiment to study the interaction of a primary jet with a confined swirling crossflow and to assess current and advanced turbulence and scalar transport models; and to conduct experimental evaluation of the air swirler interaction with fuel injectors, assessments of current two-phase models, and verification the improved spray evaporation/dispersion models.

Mongia, H. C.↗
NASA NTRS1985

Performance comparison of two interferometric droplet sizing techniques

In this paper, two interferometric techniques (Visibility/Itensity Validation and Phase Doppler) are critically examined in characterizing the spray of an air-assist nozzle with Sauter mean diameter of less than 35 microns. The two techniques are compared to each other and are evaluated against a Malvern diffraction unit. With the use of a rotating grating for Visibility/Intensity Validation, the interference techniques compare well to each other and to the diffraction method. The Phase Doppler technique is more easily applied to the spray, due largely to its broadened size and velocity ranges. The consistency of the interferometric results raises questions with regard to the use of the Malvern's most frequently applied distribution model.

Jackson, T. A.↗