Engineering topics

Sakalaukus Jr., Peter J.

Publications and source records attributed to Sakalaukus Jr., Peter J..

3 records

DOE OSTI2024

STRUCTURAL MODELING TO SUPPORT POST-YIELD ACCEPTANCE CRITERIA FOR SPENT NUCLEAR FUEL CLADDING

Spent nuclear fuel (SNF) is evaluated for structural failure during storage and transportation scenarios. The U.S. Department of Energy’s Spent Fuel and Waste Science and Technology (SFWST) program has sponsored significant research in quantifying mechanical loads on SNF during storage and transportation scenarios using experimental and modeling methods. The SFWST program has also performed significant research on measuring the mechanical behavior of irradiated SNF as defueled cladding segments and cladding with fuel pellets to measure composite behavior. This paper considers some of the key material data from the Sibling Pin testing and uses structural modeling and analysis methods that have been informed by testing to consider post-yield acceptance criteria for SNF cladding structural analysis. Test data published by Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) are the foundation for informing the material behavior of the models developed in this study. In particular, four-point bend (4PB) tests of fueled and defueled cladding segments provide significant information about the bending failure mode of SNF. ORNL’s 4PB test data is on fueled cladding segments, so the composite behavior of SNF is demonstrated. This paper describes PNNL’s coincident beam model that was developed to approximate the composite behavior of SNF. This paper also presents PNNL’s structural dynamic finite element models of a cask tip-over scenario, which is predicted to cause the strongest mechanical loads on SNF of all postulated storage and transportation scenarios. SNF bending loads predicted in the cask tip-over scenario and cladding acceptance criteria beyond yield are considered, with justification based on the Sibling Pin test data. ASME Boiler and Pressure Vessel code stress intensity limits are also considered. The ultimate goal of this work is to aid in the justification of structural acceptance criteria for SNF cladding beyond the cladding’s irradiated yield strength for use in structural analysis of all storage and transportation scenarios.

Klymyshyn, Nicholas A.↗

DOE OSTI2023

Supplemental Structural Analyses Used in Support of Certification of the Defense Programs Package 3

The Defense Programs Package (DPP)-3 is to be certified by the National Nuclear Security Administration (NNSA) Packaging and Transportation Division (PTD). Certification is based on successful physical testing of the package, and six certification test units (CTUs) have been subjected to the normal conditions of transport (NCT) and hypothetical accident conditions (HAC) outlined in Title 10 of the Code of Federal Regulations Part 71 (10 CFR 71). During regulatory testing of one of the CTUs, the drum lid closure bolt closest to the impact surface failed during the HAC 30-ft side drop. One of the testing goals for this CTU was to minimize the thermal pathway from the drum exterior shell to the containment vessel (CV) flange and O-rings, leading to the maximum damage scenario in preparation for thermal testing at 1475 °F. Therefore, the puncture bar impact proceeded as originally planned by striking the side wall of the package exterior closest to the location of the CV flange. This puncture bar impact did not attempt to exploit the region of the failed drum lid closure bolt to potentially cause more damage to the package. After the conclusion of regulatory testing, the DPP-3 package finite element model was used to numerically evaluate the effects of puncture bar impacts to the drum exterior in the vicinity of the failed drum lid closure bolt to further demonstrate the robustness of the DPP-3 design. Three alternate puncture bar impact locations and orientations were evaluated to demonstrate that these puncture bar impacts would not substantially reduce the effectiveness of the DPP-3 packaging. This paper describes the supplemental finite element models performed and structural analysis results that demonstrate the alternate HAC 40-in. puncture bar impact tests would have no deleterious effect on the performance of the DPP-3.

Sakalaukus Jr., Peter J.↗

DOE OSTI2020

Structural Analysis Approach for the Defense Programs Package 3 (DPP-3)

The Pacific Northwest National Laboratory (PNNL) is the design authority for a new Type B hazardous materials transportation package designated as the Defense Programs Package 3 (DPP-3) for the U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA). The DPP-3 has been developed using similar materials and fabrication methods employed in previous U.S. Nuclear Regulatory Commission (NRC), DOE, and NNSA certified packages. The DPP-3 design criteria are derived from the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), NNSA guidance and NRC regulatory guides in order to safely and securely transport a variety of payloads. Final regulatory approval by the NNSA will require physical testing to demonstrate that the containment vessel (CV) remains leaktight after enduring the entire regulatory testing sequence prescribed in Title 10 of the Code of Federal Regulations Part 71 (10 CFR 71). In order to gain confidence that the DPP-3 will remain leaktight after testing, the DPP-3 has been structurally analyzed using the Finite Element Analysis (FEA) software LS-DYNA. The FEA analyses serve two general purposes: first, they aid in design and development of the package, and second, they advise as to which drop orientations are expected to cause the most damage during regulatory testing. This paper will discuss how the design criteria are incorporated into analytical techniques needed to evaluate the FEA structural simulation results for 10 CFR 71 conditions to give confidence the DPP-3 testing campaign will be successful.

Sakalaukus Jr., Peter J.↗