Engineering Papers⌕ Search

Engineering topics

Sahore, Ritu

Publications and source records attributed to Sahore, Ritu.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Solvent-Free Melt-Processed Cathode Mitigates Li Anode Instability in Polymer-Based Solid-State Batteries

Solvent-free manufacturing of battery components is a promising alternative to traditional slurry processing for reducing the cost and environmental impact. In this work, we used twin-screw melt extrusion to fabricate a polymer-based high voltage composite cathode. The melt-processed cathode is dense (near zero porosity) and thick (65 μm) and has high active material loading (80 wt %). The active particles are distributed uniformly throughout the melt-processed cathode, unlike the traditional slurry-cast cathode, which exhibits inhomogeneous particle distribution. In the melt-processed cathode, polymer and carbon form separate phases, whereas in the slurry-cast cathode they blend into a single phase. Due to these structural differences, the melt-processed cathode shows smooth charge–discharge profiles, while the slurry-cast cathode shows noisy charging and soft-shorting behavior. In conclusion, this work highlights that twin-screw extrusion as a scalable, solvent-free manufacturing method is advantageous in producing uniform cathodes, which mitigates anode instability.

25 ENERGY STORAGE↗
DOE OSTI2024

The Impact of Lithium Anode Interface on Capacity Fade in Polymer Electrolyte-Based Solid-State Batteries

This study investigates the Li stripping-plating morphology and failure mechanisms in full cells consisting of a solid polymer electrolyte (SPE) with two commercial Li anodes: Li chip and Li foil. The primary identified failure mechanism of the SPE cell is capacity fade, regardless of the Li manufacturer. While the cathode’s role in capacity fade is evident, the Li anode significantly influences cycling performance, with Li foil cells cycling 50% longer than Li chip cells, a statistical difference. Further, post-mortem scanning electron microscopy and X-ray photoelectron spectroscopy results attribute the Li chip’s faster capacity fade to a loss of contact and continuous growth of the solid electrolyte interphase (SEI). Conversely, Li foil maintains consistent contact with the solid polymer, displaying a thin and stable SEI. Additionally, failure mechanisms between a gel electrolyte in previous work and the dry SPE are compared.

25 ENERGY STORAGE↗
DOE OSTI2024

Assessing cathode–electrolyte interphases in batteries

The cathode-electrolyte interphase plays a pivotal role in determining the usable capacity and cycling stability of electrochemical cells, yet it is overshadowed by its counterpart, the solid-electrolyte interphase. This is primarily due to the prevalence of side reactions, particularly at low potentials on the negative electrode, especially in state-of-the-art Li-ion batteries where the charge cutoff voltage is limited. However, as the quest for high-energy battery technologies intensifies, there is a pressing need to advance the study of cathode-electrolyte interphase properties. Here, we present a comprehensive approach to analyse the cathode-electrolyte interphase in battery systems. We underscore the importance of employing model cathode materials and coin cell protocols to establish baseline performance. Additionally, we delve into the factors behind the inconsistent and occasionally controversial findings related to the cathode-electrolyte interphase. In conclusion, we also address the challenges and opportunities in characterizing and simulating the cathode-electrolyte interphase, offering potential solutions to enhance its relevance to real-world applications.

25 ENERGY STORAGE↗
DOE OSTI2024

Electroanalytical Exploration of Li Loss at the Solid Electrolyte-Anode Interface in Anode-Free Batteries with Polymer Electrolytes

Li loss during cycling at the solid electrolyte|anode interface strongly determines the cycle life of anode-free solid-state batteries (SSBs). Here, this loss is probed electroanalytically for polymer electrolyte (PE)-based SSBs in anode-free coin cells with practical pressures. A wide range of parameters expected to impact the measured average coulombic efficiency (CE) were explored to estimate the expected range of performance. These factors include PE type, cycling profiles, current collector type, and the presence of a thin Li seed layer. Further, low CE values in the ~50%–85% range are observed for all electrolytes and test conditions. Other than the electrolyte type, a strong dependence of the CE on the electrochemical cycling profile and the type of metallic current collector is observed. Compared to the anode-free setup, the presence of a thin (5 μ m) Li seed layer did not improve the average CE for two out of three PEs, suggesting its presence to be a weak contributor in minimizing the Li loss. This work provides baseline data on the Li losses in low-pressure anode-free configuration cells with PEs.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding and controlling lithium morphology in solid polymer and gel polymer systems: mechanisms, strategies, and gaps

Lithium metal anode promises the highest theoretical energy density and may enable high energy designs such as lithium–sulfur and lithium–air batteries. However, stable lithium plating and stripping remains a challenge in all electrolyte systems including liquids, polymers, and ceramic electrolytes. In this perspective, we examine literature studies of lithium morphologies in solid polymer and gel polymer systems and compare that with well-studied liquid electrolytes. In solid polymer electrolytes, current density and mechanical properties are both governing parameters for lithium morphology, differing from conventional liquid electrolytes. Stable lithium electrodeposition may be accomplished by a polymer electrolyte with good stiffness operating at significantly lower current densities than its limiting current density, which is defined by the Sand equation. In gel polymer electrolytes, the reported lithium morphology is more similar to that in liquid electrolytes, suggesting similar nucleation and growth mechanisms. Based on experimental evidence and theoretical guidance, current strategies to control lithium morphology in solid polymer and gel polymer electrolytes are summarized. The limitations of these strategies are discussed. In particular, we note the knowledge gap in understanding the solid electrolyte interphase in solid polymer systems and the critical role it can play in regulating lithium morphologies.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Role of Scaffold Architecture and Excess Surface Polymer Layers in a 3D-Interconnected Ceramic/Polymer Composite Electrolyte

3D-interconnected ceramic/polymer composite electrolytes offer promise to combine the benefits of both ceramic and polymer electrolytes. However, an in-depth understanding of the role of the ceramic scaffold's architecture, and the associated polymer/ceramic interfaces on the electrochemical properties of such composite electrolytes is still incomplete. Here, these factors are systematically evaluated using an interconnected composite electrolyte with a tunable and well-defined architecture. The ionic conductivity of the ceramic scaffold is strongly dependent on its porosity and tortuosity, as demonstrated experimentally and via theoretical modeling. The connectivity of the ceramic framework avoids the high interfacial impedance at the polymer/ceramic electrolyte interface within the composite. However, this work discovers that the interfacial impedance between the bulk composite and excess surface polymer layers of the composite membrane dominates the overall impedance, resulting in a 1–2 order drop of ionic conductivity compared to the ceramic scaffold. Despite the high impedance interfaces, an improved Li + transference number is found compared to the neat polymer (0.29 vs 0.05), attributed to the ceramic phase's contributions toward ion transport. Further, this leads to flatter overpotentials in lithium symmetric cell cycling. These results are expected to guide future research directions toward scalable manufacturing of composite electrolytes with optimized architecture and interfaces.

25 ENERGY STORAGE↗
DOE OSTI2022

Li Morphology Evolution during Initial Cycles in a Gel Composite Polymer Electrolyte

Understanding and controlling lithium morphology evolution and lithium dendrite formation and growth during cycling is one of the key challenges for high-energy lithium metal batteries. This challenge applies to liquid electrolyte batteries as well as solid-state and semi-solid-state batteries. Our current knowledge about the evolution of the Li morphology is mostly obtained from liquid electrolyte-based studies in a Li–Li symmetrical cell configuration. The knowledge obtained in such conditions may not readily transfer into solid-state or semi-solid-state batteries. In this work, Li morphology evolution during initial cycling in a full cell configuration with the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NMC 622) cathode and a semi-solid-state gel composite electrolyte is monitored via post-mortem photographs and scanning electron microscopy at multiple length scales. The gel composite electrolyte contains a cross-linked poly(ethylene oxide)-based polymer electrolyte, ceramic fillers, and a liquid plasticizer. The results show that severe surface pitting occurs as early as the second stripping cycle. Pit formation and continuous dissolution during the stripping process are the main cause of the Li surface roughening and dendrite growth mechanism in the model gel composite electrolyte. Comparing Li dendrite growth mechanisms in liquid, polymer, and ceramic solid electrolytes, the dendrite growth mechanism observed in this model electrolyte resembles that of the liquid electrolyte the most. This study suggests that strategies to control Li morphology and prevent dendrite growth in a gel composite electrolyte should be similar to strategies applicable to liquid electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Performance of Different Water-Based Binder Formulations for Ni-Rich Cathodes Evaluated in LiNi 0.8 Mn 0.1 Co 0.1 O 2 //Graphite Pouch Cells

Water-based processing for lithium-ion battery electrodes is attractive due to its lower manufacturing cost and smaller environmental impact. However, multiple challenges associated with aqueous cathode processing have hindered commercial adoption. Polymer binders are an important component of the electrode, and thus the choice of binders can alter electrode cycling performance significantly. In this work, four different water-based binder combinations are investigated for Ni-rich LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)-based cathodes, with a focus on the long-term electrochemical performance in practical-format full pouch cells. No additional pH-modulating additives were added to the aqueous cathode slurries, and no protective coatings were present on the cathode or aluminum current collector. Results are compared with the standard PVDF/NMP-based binder/solvent combination, used as a baseline. The influence of water-based binder type on slurry rheology and electrode microstructure are also discussed. All cells made by water-processing had worse rate performance compared to the baseline. However, the cell discharge capacity after 1000 U.S. Advanced Battery Consortium (USABC) cycles at C/3 charge/discharge rate was comparable to the baseline for two of the water-based cathode formulations (CMC & JSR, and LiPAA), demonstrating the potential viability of aqueous-processed Ni-rich cathodes at a commercial scale.

25 ENERGY STORAGE↗
DOE OSTI2022

Ion Transport in Batteries with Polymer Electrolytes

We discuss polymer electrolytes for use in rechargeable lithium batteries. Polymer electrolytes have the potential to enable batteries with lithium metal anodes. These batteries have significantly higher theoretical energy densities than current lithium-ion batteries. We consider binary mixtures of polymers and salts. We also cover more complex systems such as polymer electrolytes swollen with a solvent (gel polymer electrolytes) and microphase separated polymer electrolytes. By covalently attaching the anions to the chains in a polymer solid, one obtains a single-ion conductor. We mainly focus on experiments wherein the polymer electrolyte is placed between two lithium metal electrodes. These experiments enable the determination of three transport parameters, ionic conductivity, salt diffusion coefficient, and transference number, and the thermodynamic factor. The properties of dry polymer electrolytes are contrasted with those of gel polymer electrolytes. The gel systems exhibit higher conductivity while the dry systems exhibit superior mechanical properties. We discuss interfacial impedance when lithium metal is contacted with polymer electrolytes and the importance of coulombic efficiency.

Yu, Xiaopeng↗
DOE OSTI2022

Comparing the Purity of Rolled versus Evaporated Lithium Metal Films Using X-ray Microtomography

Here, we present a comparison of lithium metal films produced via rolling and thermal evaporation using synchrotron hard X-ray microtomography. In past studies of rolled lithium metal foils, a large number of C, O, and N impurities were found and identified as the key cause for failure in lithium metal cells. In this comparison, the X-ray tomography data show that the evaporated lithium metal films have an average impurity concentration of 19 particles/mm3 in comparison to 1350 particles/mm3 in the rolled lithium metal. An analysis of the inner substrate/lithium interface and outer lithium surface of the thermally evaporated film shows a much greater concentration of impurities at these interfaces, further emphasizing the importance of interface engineering in producing high-quality lithium metal batteries. Furthermore, we show that, if surface contamination can be avoided, it is possible to obtain lithium films with no impurities detectable by synchrotron hard X-ray tomography.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Polyacrylonitrile-based electrolytes: How processing and residual solvent affect ion transport and stability

Polyacrylonitrile (PAN) is one of the alternative candidate polymer hosts to form solid polymer electrolytes (SPEs) besides the widely used poly(ethylene oxide). In this study, we systematically investigate the processing of PAN based SPEs containing lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt, using dimethylformamide (DMF) as the solvent. The effects of PAN processing procedure including solution mixing, casting, and drying on the morphology, ion transport, solvation structure, Li and oxidative stability of PAN electrolytes are thoroughly examined. In particular, four drying conditions are investigated and the amount of residual DMF is accurately determined using infrared (IR) spectroscopy. Varying the drying conditions can lead to five orders of magnitude decrease in the ionic conductivity. As DMF content decreases, the SPE's stability again Li metal dramatically improves. The practical oxidative stability is also strongly affected by the residual DMF content, ranging from 2.5 V to 3.5 V, much lower than reported values. Finally, the role of the residual DMF solvent is elucidated. DMF content vitally influences ion solvation structure at different concentration regimes, which ultimately dictates the ion conduction mechanism and oxidative stability of PAN based SPEs. In conclusion, this thorough study lays the groundwork for future development of PAN based electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A Bilayer Electrolyte Design to Enable High-Areal-Capacity Composite Cathodes in Polymer Electrolytes Based Solid-State Lithium Metal Batteries

High-areal-capacity cathodes are needed for energy-dense solid-state batteries. Here, we demonstrate a bilayer polymer electrolyte design for cycling 3–6 mAh/cm 2 NMC811 composite cathodes. In this work, the bilayer electrolyte comprises a cross-linked poly(ethylene oxide) (PEO)-based electrolyte layer and a linear-PEO-based electrolyte layer. The former provides dendritic resistance, and the latter provides a seamless interface with the cathode during cycling. Using a single layer of either membrane led to severe shorting or extremely low Coulombic efficiency (CE) in the first cycle. The general concept of a rigid dendrites-inhibiting electrolyte facing Li anode and a softer, cathode-integrated electrolyte that ensures contact with the cathodes during cycling may present a pattern for enabling high-energy-density cathodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Nanostructured ligament and fiber Al–doped Li 7 La 3 Zr 2 O 12 scaffolds to mediate cathode-electrolyte interface chemistry

In this study, scaffold structures of electrospun aluminum–substituted lithium lanthanum zirconate Li 7 La 3 Zr 2 O 12 (Al-LLZO) were synthesized and used as an additive in a LiNi 0.6 Mn 0.2 Co 0.2 O 2 composite cathode. The scaffolds were crystalized in the cubic phase after calcination at 700 °C. The Al-LLZO scaffold morphology was dependent on the precursor formulation (aqueous and dimethylformamide. The aqueous precursors resulted in scaffolds of densely coalesced ligaments, whereas the dimethylformamide precursors resulted in high–aspect ratio nanofiber scaffolds. The long-term cycling stability and rate performance of the cells were found to depend on the Al-LLZO scaffold morphology. The uniformly dispersed Al-LLZO fibers resulted in a more stable cathode electrolyte interface formation through the reduced decomposition of the LiPF 6 salt during cycling, resulting in a better high-rate and long-term cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2021

Effects of Plasticizer Content and Ceramic Addition on Electrochemical Properties of Cross-Linked Polymer Electrolyte

The development of a safe electrolyte is the key to improving energy density for next generation lithium batteries. In this work, UV-crosslinked poly(ethylene oxide) (PEO) -based polymer and composite electrolytes are systematically investigated on their ionic conductivity, mechanical and electrochemical properties. The polymer electrolytes are plasticized with non-flammable linear short-chain PEO. In the composite electrolytes, a doped lithium aluminum titanium phosphate (LATP) ceramic, LICGC™, is used as the ceramic filler. It is found that the addition of the plasticizer leads to a tradeoff between ion transport and mechanical properties. In contrast, the addition of ceramic fillers improves both the ionic conductivity and mechanical properties. The sample with 20 wt% of LICGC™ shows a conductivity of ~0.6 mS cm –1 at 50 °C. This sample also demonstrates much longer cycle life than the neat polymer electrolyte in Li platting/stripping test with a capacity of 1 mAh cm –2 . Further, a full cell made with this composite electrolyte against Li metal anode and high voltage LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode shows 94% capacity retention after 30 cycles, compared to 58% capacity retention with the neat polymer electrolyte. These results demonstrate that a hybrid of polymer/ceramic/non-flammable plasticizer is a promising path to high energy density, high voltage lithium batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Practical Considerations for Testing Polymer Electrolytes for High-Energy Solid-State Batteries

Polymer electrolytes are an important class of materials in enabling solid-state batteries, which have the potential to exceed 400 Wh/kg energy density. Despite significant advancements in their lithium-ion transport and mechanical properties over the last two decades, the integration and testing of these novel electrolyte materials into functioning cells with the electrode loadings and dimensions required to meet the cell-level energy density goals have been limited. Here, through multiple representative examples, we demonstrate the need of testing in close to practical cell conditions for a faster and more reliable evaluation of polymeric electrolytes. In particular, the need for testing with thin lithium anodes and practical cycling capacities is demonstrated for evaluation of their lithium-metal interfacial stability and dendritic resistance, respectively, and a testing protocol is suggested. The guidelines presented here will also apply to testing of other solid electrolytes for solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Aqueous Ni-rich-cathode dispersions processed with phosphoric acid for lithium-ion batteries with ultra-thick electrodes

Lithium-ion battery (LIB) production can benefit both economically and environmentally from aqueous processing. Although these electrodes have the potential to surpass electrodes conventionally processed with N -methyl-2-pyrrolidone (NMP) in terms of performance, significant issues still exist with respect to ultra-thick cathodes ($\gg$4 mAh/cm 2 areal capacities). A major concern for these types of electrodes with high-nickel active material stems from lithium leaching from active material, which drives the pH of the dispersion in excess of 12 and subsequently corrodes the current collector interface. As this corrosion reaction proceeds, hydrogen generation at the interface creates bubbles which cause severe cracking in the dried electrode surface. When areal loadings are increased, this effect becomes more pronounced and is detrimental to both mechanical and electrochemical properties of these electrodes. In this work, a technique for mitigating corrosion at the current collector by adjusting the pH of the dispersion with the addition of phosphoric acid is investigated. Phosphoric acid was added in 0.5 wt% increments between 0.0 and 1.5 wt%, and effects on rheology, adhesion, corrosion, and electrochemical performance were investigated. A technique is reported for producing aqueous processed cathodes with areal loadings of 6–8 mAh/cm 2 with reduced surface cracking and superior high-rate discharge capacity (i.e. high-power performance) for this class of cathode loadings.

25 ENERGY STORAGE↗
DOE OSTI2020

Corrosion Mitigation and Increased Discharge Capacity in Aqueous Processed Thick Cathodes using Phosphoric Acid Additives

Aqueous processed cathodes for lithium-ion batteries are favorable for both cost and environmental reasons; however, these electrodes still face significant problems with increasing areal capacities (i.e. thickness). Highly basic slurry conditions (pH in excess of 12) corrode the current collector surface and evolve hydrogen gas. Consequently, bubbling at the electrode interface causes substantial damage to the dried electrode. As the loading of these electrodes is increased, damage becomes severe and results in lack of adhesion and cohesion. Here introduction of phosphoric acid to combat the rise in pH and suppress the corrosion at the current collector surface is investigated. Phosphoric acid was added in increments of 0.5, 1.0, and 1.5 wt% and the subsequent effects on slurry rheology, particle size, adhesion, and electrochemical cycling were investigated. A technique is reported for obtaining thick (6-8 mAh/cm2) cathodes that exhibit reduced surface cracking and improved rate performance as compared to control samples.

Kukay, Alexander↗