Engineering Papers⌕ Search

Engineering topics

Sabau, Adrian

Publications and source records attributed to Sabau, Adrian.

At least 19 records

Prediction of microstructure formation in laser powder bed fusion process.

The datasets are results analyzing the predicted microstructures in a single track during the laser powder bed fusion additive manufacturing process. They are the outputs by running the opensource code, muMatScale (The code can be cited at: Yuan, Lang, Fattebert, Jean-Luc, and Sabau, Adrian. (2023, August 03). muMatScale. [Computer software]. https://github.com/lang-yuan/muMatScale. https://doi.org/10.11578/dc.20240112.2.) For each set of data, it contains the time-dependent information of Temperature, Fraction Solid, Grain ID, Grain Angle ( crystallographic orientations by Euler angles), and solute Composition. The dataset can be visualized by Paraview (https://www.paraview.org/ ). The 6 datasets are: 1. Baseline_base1_n4e14_dt20: baseline case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 2. Nuc_n4e15_dt20: case with bulk nucleation density of 4E+15/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 3. Nuc_n4e15_dt50: case with bulk nucleation density of 4E+15/m^3, undercooling of 50K, substrate nucleation density of 1.5E+15/m^3 4. Nuc_n6e15_dt20: case with bulk nucleation density of 4E+16/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 5. Base4_n4e14_dt20: case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 6.0E+15/m^3 6. Base16_n4e14_dt20: case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 2.4E+16/m^3

36 MATERIALS SCIENCE↗

Pulse Strengthened and Laser Edge Sealed Vacuum Insulation Glazing

A scalable, low-cost processing strategy for glass strengthening and sealing is proposed to improve the thermal performance of insulating glass units and develop innovative window technologies. In this project, a combination of large area photonic processing, additive manufacturing, and laser encapsulation techniques is reported to realize a vacuum glazing technology to meet the cost, performance, reliability, and throughput demands. A modeling framework for evaluating the mechanical and thermal response was established to verify the structural deformation and thermal conductance. Micro-size glass frits in printing ink and a continuous-wave laser curing were employed to allow the formation of a hermetic bonding layer and led to improvement of glass edge sealing. Various sealing parameters, including laser traveling speed, spot diameter, and laser power were optimized. The water seepage and mechanical strength of the resulting glass-to-glass bonding were examined as well. These results showcase the development of a practical vacuum insulating glazing with several unique features through a combination of photonic processing, laser encapsulation, and additive manufacturing.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Design optimization of an additively manufactured prototype recuperator for supercritical CO 2 power cycles

Supercritical CO 2 (sCO 2 ) power cycles are being developed due to their potential for high efficiency and reduced capital cost. It is necessary that these recuperators operate at high pressures and temperatures, up to 30 MPa and 900 K, with effectiveness values > 95% and pressure drops <1% to achieve high cycle efficiencies. Moreover, it is also necessary to have reasonable cost recuperators to control the capital costs of the sCO 2 power cycles. In this study, a Plate Pin-Fin (PPF) heat exchanger has been proposed as an sCO 2 recuperator. This preliminary recuperator design leverages capabilities enabled by additive manufacturing. Although the PPF design has characteristics similar to those of a plate heat exchanger, small diameter and relatively long fins are used to increase surface area, enhance heat transfer, and provide structural support for the partition plates that separate the fluid streams. Existing correlations for heat transfer and pressure drop were adapted for the PPF heat exchanger. These correlations were implemented in a 1D analytical model and used for the optimization of a 5-kW th high temperature recuperator for an indirect sCO 2 cycle by varying the design parameters to minimize the quantity of material required. A 3D conjugate heat transfer numerical simulations were conducted to validate the heat transfer and pressure loss correlations. A steepest descent method was used to minimize heat exchanger mass for a 5-kW prototype recuperator subject to a maximum specified pressure drop. Additionally, the design analysis indicated that an optimum PPF recuperator would be attained for the minimum allowable pin transverse spacing, minimum pin width, minimum pin height and near maximum cell aspect ratio. Moreover, at a low material requirement of 0.216 kg/kW and a pressure drop, which is almost five times lower than the allowable pressure drop design target, the optimized PPF heat exchanger has the high potential to be an alternative to a printed circuit heat exchanger, which is a conservative design basis for the current state-of-the-art sCO 2 recuperators.

42 ENGINEERING↗

ADDITIVELY MANUFACTURED SURFACE HEAT TRANSFER ENHANCEMENTS FOR THE TRANSFORMATIONAL CHALLENGE REACTOR

The Transformational Challenge Reactor (TCR) is a high-temperature gas-cooled reactor design that uses additively manufactured fuel elements. TCR fuel elements have walls made of silicon carbide and are filled with tristructural-isotropic fuel particles. These fuel elements can have radically different shapes and integrated features than existing designs due to the reduced cost for complex structures in binder jet additive manufacturing. As such, binder jet additive manufacturing enables wall surface features to be embedded that can deliver superior heat transfer performance than smooth wall designs. In this work, the authors conducted a computational fluid dynamics study to evaluate selected wall features integrated into TCR fuel elements. Results show that surface features can outperform smooth wall designs; however, there are unique challenges for gas-cooled reactor core designs that have not been fully explored by previous research. For example, the rough surface finish and process variability of ceramics additive manufacturing make it challenging to predict surface roughness effects before fabrication. Additionally, the small hydraulic diameters of coolant channels in reactor cores make it difficult to engineer surface features that do not significantly increase the pressure drop. Engineers must carefully size surface features for heat transfer enhancement in additive fuel elements to operate above the base material's surface roughness effects and below the coolant channel size.

Weinmeister, Justin↗

Measurement of Convective Heat Transfer Coefficients with Supercritical CO2 in Novel Additively Manufactured Helically Patterned Pin Fin Tubes Using the Wilson Plot Technique

This paper describes the measurement of convective heat transfer coefficients and friction factors for sCO2 flowing in pin-fin patterned pipes in the Heat Exchange and Experimental Testing (HEET) facility at the US DoE’s National Energy Technology Laboratory (NETL) in Morgantown, WV. The measurement procedures in the HEET rig were validated by conducting benchmark tests with smooth stainless-steel tube and comparing the results with published correlations for Nusselt number (Nu) and friction factor. Over typical Reynolds number range in sCO2, the measured Nu and friction factors were within 7% of classical correlations for smooth tube flow.The candidate pin fin patterned pipes were additively manufactured (AM) at the Oak Ridge National Laboratory. The pins were circular or elliptical in cross-section. Pin length to diameter aspect ratios were 1.33 and 2, while the pin diameter to tube diameter ratio was 0.188 and 0.125. Tests were performed for ReD varying from 6.9×104 to 2.2×105 and at conditions equivalent to the low pressure outlet (8.69 MPa, 361 K) of the low temperature recuperator (LTR) in an indirect sCO2 power cycle. The Wilson plot technique was utilized to measure the bulk heat transfer coefficients.For the better performing design (tube A, pin length to tube diameter ratio: 1.33, pin diameter to tube diameter ratio: 0.188), the local heat transfer coefficient increased by 112% relative to the Dittus-Boelter correlation at the LTR low pressure outlet. This corresponded to a 282% increase in the product of the heat transfer coefficient and the surface area. Large pressure drops across the test articles were observed.

Searle, Matthew↗

Aluminum alloy compositions and methods of making and using the same

The present disclosure concerns embodiments of aluminum alloy compositions exhibiting microstructural stability and strength at high temperatures. The disclosed aluminum alloy compositions comprise particular combinations of components that contribute the ability of the compositions to exhibit improved microstructural stability and hot tearing resistance as compared to conventional alloys. Also disclosed herein are embodiments of methods of making and using the alloys.

Shyam, Amit↗

ExaAM: Metal additive manufacturing simulation at the fidelity of the microstructure

Additive manufacturing (AM), or 3D printing, of metals is transforming the fabrication of components, in part by dramatically expanding the design space, allowing optimization of shape and topology. However, although the physical processes involved in AM are similar to those of welding, a field with decades of experimental, modeling, simulation, and characterization experience, qualification of AM parts remains a challenge. The availability of exascale computational systems, particularly when combined with data-driven approaches such as machine learning, enables topology and shape optimization as well as accelerated qualification by providing process-aware, locally accurate microstructure and mechanical property models. We describe the physics components comprising the Exascale Additive Manufacturing simulation environment and report progress using highly resolved melt pool simulations to inform part-scale finite element thermomechanics simulations, drive microstructure evolution, and determine constitutive mechanical property relationships based on those microstructures using polycrystal plasticity. We report on implementation of these components for exascale computing architectures, as well as the multi-stage simulation workflow that provides a unique high-fidelity model of process–structure–property relationships for AM parts. In addition, we discuss verification and validation through collaboration with efforts such as AM-Bench, a set of benchmark test problems under development by a team led by the National Institute of Standards and Technology.

3D printing↗

Dual-Purpose Canister Filling Demonstration Project Progress Report

This report discusses the progress made at the Oak Ridge National Laboratory to support direct disposal of dual-purpose canisters (DPCs). Acceptable filler materials should demonstrate that the probability of criticality in DPCs during the disposal timeframe is below the probability threshold for inclusion in a repository performance assessment. This effort, which will ultimately result in a full-scale demonstration, includes computational fluid dynamics (CFD) modelling developed to gauge the filling process and to uncover any unforeseen issues. Filling simulations of the lower region (mouse holes) of a prototypic DPC show successfully simulate filling of the void space inside the canister and a smooth, even progression of the liquid level. Flow through a pipe that is similar to the drainpipe in a DPC is being investigated separately to gain valuable insight of the flow regime inside a pipe. Three physical experiments validating the computational filling model have been completed using surrogate liquids. One experiment using molten metal has been completed and the results demonstrate adequate filling of the canister void spaces. Although the scale experiment observed some void spaces related to shrinkage of the metal during cooling, the volume filled is expected to be sufficient to meet the purpose of moderator exclusion. Further experiments will scale up the geometry, moving towards a full-sized DPC demonstration, and provide a more rigorous investigation of candidate filler materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ADVANCED THERMAL-HYDRAULIC MODEL OF HEAT RECOVERY STEAM GENERATORS

Steam-side oxidation at elevated temperatures in heat recovery steam generators (HRSGs) can lead to overheating of local tubes, potential oxide scale exfoliation, and damage to critical equipment. Predicting the oxide growth distribution requires detailed knowledge of the distribution of tube metal temperatures. To address these challenges, a computational fluid dynamics (CFD) model of a high-pressure superheater (HPSH) was developed within the Siemens’ STAR-CCM+ CFD commercial software. The HPSH section of the steam generator was selected for modeling because of its high oxidation rates.The model development included several steps. In the first step, an oxidation model based on a parabolic oxidation relationship was implemented. The oxidation growth predicted by the model was then verified for a full-load boiler operation case. In the second step, a three-dimensional CFD model was developed to account for the thermal and flow physics involved in HRSGs. The CFD model was then verified and validated on a simplified geometry that contained six row-tubes which mimicked the tube arrangements of an HPSH section. Numerical results compared well with published experimental results. In the third step, the oxidation model was coupled to the HRSG’s CFD model, and a comparison study was performed for two cases: (a) regular finless tubes and (b) finned tubes. Preliminary results showed that the oxide thickness predicted by the case with tube fins was higher compared to that of the finless tube case, thus demonstrating the need to model the effects of the tube fins on oxide thickness.

Panicker, Nithin↗

Surface and subsurface characterization of laser-interference structured Ti6Al4V

Ti6Al4V specimens were exposed to high-energy laser pulses of 1.24 J/cm 2 fluences per pulse using a two-beam optical configuration to attain laser-interference. In addition to the formation of periodic surface textures by laser-interference, scanning electron microscope (SEM) images demonstrated several microstructural changes on the surface processed. Moreover, the surface and subsurface of Ti6Al4V specimens were characterized for the as-received and laser-interference processed conditions using x-ray photoelectron spectroscopy (XPS) and electron energy dispersive spectroscopy (EDS). The XPS data showed that this laser technique is effective at removal of surface contaminants for Ti6Al4V. The XPS analysis also revealed the formation of an oxy-nitride layer on the laser treated material. Finally, the microstructure analysis indicates that grain refinement, dendrite and twin structures were found near the surface due to laser processing.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Laser-Interference Structured AA2024 Coated with a Chromate-Containing Epoxy Primer

In this study, the corrosion behavior of laser-interference treated AA2024-T3 specimens, which are coated with a primer, is presented. The surface of as-received AA2024-T3 specimens were laser-interference structured by splitting the primary beam of a Q-switched Nd:YAG pulsed nanosecond laser into two beams and focusing them to the same spot on the specimen surface. After being stored in plastic cases for up to 70 d, without any additional cleaning, the specimens were spray painted with a chromate-containing epoxy primer, CA7233, compliant to MIL-PRF-23377 Type I Class C2 specification. The corrosion behavior of laser-interference specimens was assessed against that of specimens prepared by chromated conversion coating and sulfuric acid anodizing treatments. After the ASTM B117 corrosion exposure, it was found that the laser processed specimens exhibited only few blisters. On one hand, most specimens prepared at a laser fluence of 1.78 J/cm 2 , without any additional chemical cleaning, were found to develop one very small blister after only 96 h of exposure. However, the growth of these blisters was not significant even after 1,000 h of salt spray exposure. On the other hand, only a fraction of the specimens prepared at a laser fluence of 1.24 J/cm 2 and acetone wiped right after the laser structuring were found to develop several tiny blisters after 790 h and longer exposure. Overall, it was found that the corrosion damage was minimized at a laser rastering speed of 4 mm/s, a condition for which only 33% of specimens developed very minor corrosion damage. Furthermore, the ASTM D1654 creepage ratings, which was used to evaluate the corrosion damage along the scribe lines, were found to be at least nine for all coated panels. These results indicate that the laser-interference technique with the additional acetone wiping has the potential to be further developed as a nonchemical surface preparation technique for chromate-containing epoxy primers coating systems.

36 MATERIALS SCIENCE↗

Heat Transfer Coefficients of Additively Manufactured Tubes with Internal Pin Fins for Supercritical Carbon Dioxide Cycle Recuperators

This paper describes the measurement of convective heat transfer coefficients and friction factors for sCO 2 flowing in additively manufactured tubes with internal pin fins at the US DOE’s National Energy Technology Laboratory in Morgantown, WV. The measurement procedures were validated by conducting benchmark tests with smooth stainless-steel tube and comparing the results with published correlations for Nusselt number (Nu) and friction factor. Over Reynolds numbers (ReD) ranging from 5 × 10 4 to 2.5 × 10 5 , measured Nu was within 5% of the Dittus-Boelter correlation and measured friction factors were within 5% of the McAdams correlation for smooth tube flow. The candidate pin fin patterned pipes were additively manufactured (AM) at the Oak Ridge National Laboratory. The pins were circular or elliptical in cross-section and were printed at a 30⁰ angle relative to the inner wall (to meet AM constraints). The pin arrangement was helical to promote enhanced heat transfer due to swirl flow. Pin length to diameter aspect ratio was 1.33, 2, and 8, while the pin diameter to tube diameter ratio was 0.188, 0.125, and 0.063. Tests were performed for ReD varying from 6.9 × 10 4 to 2.2 × 10 5 and at conditions equivalent to the low pressure (LP) outlet (8.69 MPa, 361 K) and the high pressure (HP) inlet (20.7 MPa, 350 K) of the low temperature recuperator (LTR) in an indirect sCO 2 cycle. The Wilson plot technique was utilized to measure the bulk heat transfer coefficients. For the best performing design (tube A, pin length to tube diameter ratio: 1.33, pin diameter to tube diameter ratio: 0.19), the local heat transfer coefficient increased by 136% relative to the Dittus-Boelter correlation at the LTR low pressure outlet and 194% at the LTR high pressure inlet. These correspond to a 282% and a 271% increase in the product of the heat transfer coefficient and surface area (adjusted for fin efficiency) product, respectively. Large pressure drops across the test articles were observed. For Tube Design A, the average friction factor, across the range of ReD considered, was significantly larger than the McAdams correlation at both the LTR LP outlet and the LTR HP inlet. A thermal performance factor was utilized to express the ratio of material required to build a finned heat exchanger relative to a finless heat exchanger with the same heat duty and pumping power. Tube Design A was estimated to decrease the required heat exchanger material by 13%.

Searle, Matthew↗

Laser-interference pulse number dependence of surface chemistry and sub-surface microstructure of AA2024-T3 alloy

The laser-based treatment of a metal surface is an intrinsically non-chemical technique that can alter both the topology and chemistry of surfaces. A laser-based treatment for coating and joining applications can offer alternative surface preparations to the chemically-based surface preparation techniques, which are subject to severe environmental protection and hazardous-waste management considerations. In this study, the surface chemistry and sub-surface microstructural changes are investigated for a novel surface processing method using laser interferometry produced by two beams of a pulsed Nd:YAG laser. The two-beam laser-interference allowed the structuring of the surface at length scales much less than that of the laser beam spot. Surface chemistry changes in the oxide layer of AA 2024-T3 aluminum alloy rolled sheet due to laser processing were investigated using x-ray photoelectron spectroscopy (XPS). Near surface microstructural changes have been investigated with scanning electron microscopy and energy dispersive x-ray spectroscopy (SEM/EDS), and scanning transmission electron microscopy (STEM) as a function of number of interfering laser shots. SEM microstructure pictures of the top surface shows the minimization of surface defects, as all of the sharp features from a rolled sheet surface were smoothed by laser-structuring. STEM images indicate that the laser-interference processing reduced the formation of CuMn-rich precipitates over a 500–800 nm depth from the top surface. XPS data indicated that the Al oxide layer is modified compared to that of the baseline specimen and that the oxide thickness increases with the number of shots per spot. Finally, the additional thicker oxide on Al alloys is expected to increase the corrosion resistance of the coated Al 2024.

36 MATERIALS SCIENCE↗

Conjugate Heat Transfer Analysis of the Supercritical CO2 Based Counter Flow Compact 3D Heat Exchangers

Compact heat exchangers using supercritical fluids such as CO2 are preferred due to their high heat transfer capacity and smaller footprint. Three-dimensional conjugate forced convection heat transfer analysis was performed on several shell-and-tube counter-flow microchannel heat exchangers. Numerical simulations were conducted to test effect of change in mass flow rate, hydraulic diameter and various cross sections on the heat transfer. Increasing mass flow rate improved heat transfer up to a maximum value and then decreased downstream with increasing turbulence. Maximum heat transfer was obtained for the micro channel with the smallest hydraulic diameter. Amongst the cross sections analyzed (circular, square, circular with radial ribs, and square with radial ribs), the most uniform distribution of temperature and maximum heat transfer were obtained for circular cross section with radial ribs. An optimally efficient operation of such a heat exchanger can be attained by considering these factors during multi-objective constrained optimization of geometric parameters and requirements for additive manufacturing of such compact heat exchangers.

Chitale, Janhavi↗

Columnar-to-equiaxed transition in a laser scan for metal additive manufacturing

In laser powder bed fusion additive manufacturing (LPBFAM), different solidification conditions, e.g., thermal gradient and cooling rate, can be achieved by controlling the process parameters, such as laser power and laser speed. Tailoring the behaviour of the columnar to equiaxed transition (CET) of the printed alloy during fabrication can facilitate the production of highly customized microstructures. In this study, effective analytical solutions for both thermal conduction and solidification are employed to model solidifying melt pools. Microstructure textures and solidification conditions are evaluated for numerous combinations of laser power and laser speed under bead-on-plate conditions. This analytical-based high-throughput tool was demonstrated to select specific process parameters that lead to desired microstructures. Two selected process conditions were examined in detail by a highly parallelized microstructural solidification model to reveal both nucleation and grain growth. Both numerical solutions agree well with experiments that are performed based on bead-on-plate conditions, indicating that these numerical models aid evaluation of the nucleation parameters, providing insights for controlling CET during the LPBFAM processing.

Lang, Yuan↗