Engineering Papers⌕ Search

Engineering topics

Russell, G. R.

Publications and source records attributed to Russell, G. R..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Nuclear pumped laser research at the Jet Propulsion Laboratory

Using a partially nuclear excited xenon flashlamp to pump an iodine laser, laser pulse shapes were analyzed with and without nuclear flashlamp augmentation. The pulse shapes indicate that the deposition of nuclear energy is equally as effective as electrical energy deposition in producing laser pulse energy output. The amplification of the E-beam pumped CF3I was measured at pressures of several atmospheres. Preliminary data shows that, for a part of the iodine laser pulse, amplification of almost a factor of two is measured. This measurement indicates that the gain in an E-beam pumped CF3I is an order of magnitude greater than in the coaxial laser tube.

Russell, G. R.↗
NASA NTRS1978

A continuously pulsed copper halide laser with a cable-capacitor Blumlein discharge circuit

Experimental characteristics of a continuously pulsed copper halide laser with a cable-capacitor Blumlein discharge circuit are reported. Quartz laser tubes 1 m in length and 1.5 and 2.5 cm in diameter were employed to study the effects of the electrical circuit, lasant, and buffer gas on laser performance. Measured properties of the Blumlein circuit are compared with an analytic solution for an idealized circuit. Both CuCl and CuBr with neon and helium buffer gas were studied. A maximum average power of 12.5 W was obtained with a 1.5 nF capacitor charged to 8 kV and discharged at 31 kHz with CuCl and neon buffer gas at 0.7 kPa in a 2.5-cm-diam tube. A maximum efficiency of 0.72 percent was obtained at 9 W average power. Measurements of the radial distribution of the power in the laser beam and the variation of laser power at 510.6 and 578.2 nm with halide vapor density are also reported. Double and continuously pulsed laser characteristics are compared, and the role of copper metastable level atoms in limiting the laser pulse energy density is discussed.

Nerheim, N. M.↗
NASA NTRS1978

Long-duration high-efficiency operation of a continuously pulsed copper laser utilizing copper bromide as a lasant

A copper laser utilizing copper bromide as a lasant and neon as the buffer gas has been operated at an average laser power of between 16 and 19.5 W for a period of 68 h. Lasing was attained at a pulsing rate of 16.7 kHz in a quartz discharge tube 2.5-cm in diameter with an electrode separation of 200 cm. The laser energy/pulse and peak power/pulse corresponding to an average power of 19.5 W are 1.2 mJ and 30 kW, respectively. The ratio of laser power at 510.6 and 578.2 nm varied from 3.9 to 1.1 corresponding to a total average laser power of 4 and 18 W, respectively. The highest wall plug and capacitor efficiency measured during 68 h of operation were 0.7 and 1.1%, respectively.

Chen, C. J.↗
NASA NTRS1978

Scaling a double-pulsed copper chloride laser to 10 mJ

By use of low-inductance (0.5micro H) discharge circuits, pulses of 9.6 mJ were obtained from a double-pulsed CuCl laser. An oscillator-amplifier configuration produced a pulse energy of 11 mJ. Scaling studies indicate that additional increases in the laser energy could be obtained by increasing the discharge voltage above 20 kV and/or by increasing the laser-tube dimensions.

Nerheim, N. M.↗
NASA NTRS1977

Isotope separation using metallic vapor lasers

The isotope U235 is separated from a gasified isotope mixture of U235 and U238 by selectively exciting the former from the ground state utilizing resonant absorption of radiation from precisely tuned lasers. The excited isotope is then selectively ionized by electron bombardment. It then is separated from the remaining isotope mixture by electromagnetic separation.

Russell, G. R.↗
NASA NTRS1977

Efficient copper-vapor pulsed laser

High velocity flow is attained within system by expanding heated mixture of copper vapor, argon, and helium through supersonic nozzle. Arc heater, operated on argon/helium mixture, supplies energy to vaporize copper and to produce high temperature supersonic flow of gas/vapor mixture.

Russell, G. R.↗
NASA NTRS1976

Outlook for metal lasers

Lasers utilizing atomic metallic vapors are considered with emphasis on a double discharge technique and multiply pulsed experiments. Data are presented on the effect of time delay after the first electrical discharge and the effect of lasant temperature along with results of absorption measurements utilizing a 13 mm diameter laser tube. Data obtained from multiply pulsed experiments for discharge diameters varying from 1 to 4 cm indicate that the efficiency increases with the pulsing rate.

Russell, G. R.↗
NASA NTRS1975

Double-discharge copper-vapor laser

Power supply for discharge pulses consists of two capacitors that are made to discharge synchronously with adjustable time intervals. First pulse is switched with hydrogen thyratron, and second by spark gap. Lasing action peaks for appropriate combination of these two parameters.

Chen, C. J.↗
NASA NTRS1973

Double-discharge copper vapor laser with copper chloride as a lasant

A copper vapor laser utilizing copper chloride as a lasant in a heated discharge tube has been studied. The lasing action was observed only when two successive discharge current pulses at suitable time intervals were applied. The first pulse is considered to be a dissociation pulse to produce copper and chlorine atoms; the second to be a pumping pulse to produce population inversion. The maximum energy density measured to date was 17 microjoule/cu cm.

Chen, C. J.↗
NASA NTRS1972

Supersonic electrical-discharge copper vapor laser.

A copper vapor laser, utilizing a pulsed discharge transverse to a supersonic flow of copper vapor, argon, and helium and oscillating at 5106 and 5782 A, has been built and tested. Laser energy densities per pulse of 2.5 microjoules per cu cm have been achieved to date. Laser pulse widths of up to 185 nsec have been obtained with delay times after initiation of the current pulse of 220 to 250 nsec. Both the delay time and pulse width are in good agreement with theoretical predictions. Quenching of the laser pulse is shown to be due to a rapid increase in the rate of equilibration of the lasing levels by electron collisions, and to a decrease in the differential pumping of the lasing levels from the ground state because of a decay in the electron temperature.

Russell, G. R.↗
NASA NTRS1971

Nuclear pumping of lasers.

Summary of the theoretical and experimental work dealing with nuclear lasers that has been completed during the last year (1971), and review of some new work which may help to establish the direction research in this field may take in the future. So far, the most successful experiments have been carried out utilizing nuclear enhancement of electrically excited CO2 lasers. The goal of attaining lasing in gases utilizing nuclear pumping without an applied electric field is much more difficult to achieve but is being pursued. No experimental or theoretical work has been undertaken thus far in the study of the class of lasers where high-energy particles are produced internally in high-temperature multiple ionized plasmas. Some new approaches to high-power nuclear lasers are suggested.

Russell, G. R.↗