Engineering topics

Ross, James C.

Publications and source records attributed to Ross, James C..

34 records · Page 2

NASA NTRS1997

Reducing Wind Tunnel Data Requirements Using Neural Networks

The use of neural networks to minimize the amount of data required to completely define the aerodynamic performance of a wind tunnel model is examined. The accuracy requirements for commercial wind tunnel test data are very severe and are difficult to reproduce using neural networks. For the current work, multiple input, single output networks were trained using a Levenberg-Marquardt algorithm for each of the aerodynamic coefficients. When applied to the aerodynamics of a 55% scale model of a U.S. Air Force/ NASA generic fighter configuration, this scheme provided accurate models of the lift, drag, and pitching-moment coefficients. Using only 50% of the data acquired during, the wind tunnel test, the trained neural network had a predictive accuracy equal to or better than the accuracy of the experimental measurements.

Ross, James C.↗

NASA NTRS1997

Neural Network Prediction of New Aircraft Design Coefficients

This paper discusses a neural network tool for more effective aircraft design evaluations during wind tunnel tests. Using a hybrid neural network optimization method, we have produced fast and reliable predictions of aerodynamical coefficients, found optimal flap settings, and flap schedules. For validation, the tool was tested on a 55% scale model of the USAF/NASA Subsonic High Alpha Research Concept aircraft (SHARC). Four different networks were trained to predict coefficients of lift, drag, moment of inertia, and lift drag ratio (C(sub L), C(sub D), C(sub M), and L/D) from angle of attack and flap settings. The latter network was then used to determine an overall optimal flap setting and for finding optimal flap schedules.

Norgaard, Magnus↗

NASA NTRS1997

Aerodynamics of a Simple Three-Dimensional High-Lift System

Experimental results are presented for a three-element high-lift system with a half-span flap and both a full- and three-quarter span slat. The simplified wing spanned the wind-tunnel test section with no wing sweep or wing tip. Full- and part-span slat configurations were tested to investigate the three-dimensional effects of a finite-span slat in a landing configuration. With a part-span slat, flow visualization and surface pressures revealed two vortices at the flap tip and one at the slat tip. Compared to the full-span slat case, the part-span slat configuration stalled at a lower angle of attack and yielded reduced lift at all angles of attack. At a representative approach attitude (10 deg), wake surveys indicated comparable induced drag for the full- and part-span slat configurations while the profile drag was more than doubled with a part-span slat. The vorticity contribution of the slat-tip vortex was minimal, suggesting that the vortex dissipates through viscous interaction with the main-element boundary layer. The addition of a lower-surface fence at the slat tip yielded two co-rotating vortices and partially alleviated the profile drag increase of the part-span slat.

Storms, Bruce↗

NASA NTRS1995

Experimental Study of Lift-Enhancing Tabs on a Two-Element Airfoil

The results of a wind-tunnel test are presented for a two-dimensional NASA 63(sub 2)-215 Mod B airfoil with a 30% chord single-slotted flap. The use of lift-enhancing tabs (similar to Gurney flaps) on the lower surface near the trailing edge of both elements was investigated on four nap configurations. A combination of vortex generators on the flap and lift-enhancing tabs was also investigated. Measurements of surface-pressure distributions and wake profiles were used to determine the aerodynamic performance of each configuration. By reducing flow separation on the flap, a lift-enhancing tab at the main-element trailing edge increased the maximum lift by 10.3% for the 42-deg flap case. The tab had a lesser effect at a moderate flap deflection (32 deg) and adversely affected the performance at the smallest flap deflection (22 deg). A tab located near the flap trailing edge produced an additional lift increment for all flap deflections. The application of vortex generators to the flap eliminated lift-curve hysteresis and reduced flow separation on two configurations with large flap deflections (greater than 40 deg). A maximum-lift coefficient of 3.32 (17% above the optimum baseline) was achieved with the combination of lift-enhancing tabs on both elements and vortex generators on the flap.

Storms, Bruce L.↗

NASA NTRS1995

Lift-Enhancing Tabs on Multielement Airfoils

The use of flat-plate tabs (similar to Gurney flaps) to enhance the lift of multielement airfoils is extended here by placing them on the pressure side and near the trailing edge of the main element rather than just on the furthest downstream wing element. The tabs studied range in height from 0.125 to 1.25% of the airfoil reference chord. In practice, such tabs would be retracted when the high-lift system is stowed. The effectiveness of the concept was demonstrated experimentally and computationally on a two-dimensional NACA 63(sub 2)-215 Mod B airfoil with a single-slotted, 30%-chord flap. Both the experiments and computations showed that the tabs significantly increase the lift at a given angle of attack and the maximum lift coefficient of the airfoil. The computational results showed that the increased lift was a result of additional turning of the flow by the tab that reduced or eliminated now separation on the flap. The best configuration tested, a 0.5%-chord tab placed 0.5% chord upstream of the trailing edge of the main element, increased the maximum lift coefficient of the airfoil by 12% and the maximum lift-to-drag ratio by 40%.

Ross, James C.↗

NASA NTRS1995

Experiments in High-Lift for High-Speed Civil Transports

The lecture will present experimental work pertaining to HSCT high-lift aerodynamic testing. The effects of Reynolds number and test techniques will be discussed. The performance of attached-flow and leading-edge vortex-control high-lift devices will also be presented. All of the aerodynamic data presented will be from experiments performed prior to the HSR program. The subject of airframe noise testing and its relevance to highlift testing will be discussed but no quantitative data will be presented.

Ross, James C.↗

NASA NTRS1995

Computational Investigation of a Semi-Span Flap

The current study computationally examines one of the principle three-dimensional features of the flow over a high-lift system, the flow associated with a flap edge. Structured, overset grids were used in conjunction with an incompressible Navier-Stokes solver to compute the flow over a two-element high-lift configuration. The computations were run in a fully turbulent mode using the one-equation Baldwin-Barth model. Specific interest was given to the details of the flow in the vicinity of the flap edge, so the geometry was simplified to isolate this region. The geometry consisted of an unswept wing, which spanned a wind tunnel test section, equipped with a single element flap. Two flap configurations were computed; a full-span and a half-span Fowler flap. The chord based Reynolds number was 3.7 million for all cases. The results for the full-span flap agreed with two-dimensional experimental results and verified the method. Grid topologies and related issues for the half-span flap geometry are discussed. Results of the half-span flap case are presented with emphasis on the flow features associated with the flap edge.

Mathias, Donovan, L.↗

NASA NTRS1994

Lift enhancing tabs for airfoils

A tab deployable from the trailing edge of a main airfoil element forces flow onto a following airfoil element, such as a flap, to keep the flow attached and thus enhance lift. For aircraft wings with high lift systems that include leading edge slats, the slats may also be provided with tabs to turn the flow onto the following main element.

Ross, James C.↗

NASA NTRS1992

Flow-Control Devices For Inlets Of Indraft Wind Tunnels

Report presents theoretical and experimental study of effects of antiturbulence flow-control devices in inlet of indraft wind tunnel upon nonuniformity of flow in test section of tunnel. Flow-control devices in question include vanes, screens, and honeycombs, placed in inlet upstream of contracting section of tunnel leading from inlet to test section.

Ross, James C.↗

NASA NTRS1992

Computational evaluation of an airfoil with a Gurney flap

A 2D numerical investigation was performed to determine the effect of a Gurney flap on a NACA 4412 airfoil. A Gurney flap is a flat plate on the order of 1 to 3 percent of the airfoil chord length, oriented perpendicular to the airfoil chord line and located at the trailing edge of the airfoil. An incompressible Navier Stokes code, INS2D, was used to calculate the flow field about the airfoil. The fully turbulent results were obtained using the Baldwin-Barth one-equation turbulence model. Gurney flap sizes of 0.5 , 1, 1.25, 1.5, 2, and 3 percent of the airfoil chord were studied. Computational results were compared with experimental results where possible. The numerical solutions show that the Gurney flap increases airfoil lift coefficient with only a slight increase in drag coefficient. Use of a 1.5 percent chord Gurney flap increases the maximum lift coefficient by approximately 0.3 and decreases the angle of attack for a given lift coefficient by more than 3 deg. The numerical solutions exhibit detailed flow structures at the trialing edge and provide a possible explanation for the increased aerodynamic performance.

Jang, Cory S.↗

NASA NTRS1991

Aerodynamic performance of a drag reduction device on a full-scale tractor/trailer

The effectiveness of an aerodynamic boattail on a tractor/trailer road vehicle was measured in the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Results are examined for the tractor/trailer with and without the drag reduction device. Pressure measurements and flow visualization show that the aerodynamic boattail traps a vortex or eddy in the corner formed between the device and the rear corner of the trailer. This recirculating flow turns the flow inward as it separates from the edges of the base of the trailer. This modified flow behavior increases the pressure acting over the base area of the truck, thereby reducing the net aerodynamic drag of the vehicle. Drag measurements and pressure distributions in the region of the boattail device are presented for selected configurations. The optimum configuration reduces the overall drag of the tractor/trailer combination by about 10 percent at a zero yaw angle. Unsteady pressure measurements do not indicate strong vortex shedding, although the addition of the boattail plates increases high frequency content of the fluctuating pressure.

Lanser, Wendy R.↗

NASA NTRS1989

Theoretical and experimental study of flow-control devices for inlets of indraft wind tunnels

The design of closed circuit wind tunnels has historically been performed using rule of thumb which have evolved over the years into a body of useful guidelines. The development of indraft wind tunnels, however, has not been as well documented. The design of indraft wind tunnels is therefore generally performed using a more intuitive approach, often resulting in a facility with disappointing flow quality. The primary problem is a lack of understanding of the flow in the inlet as it passes through the required antiturbulence treatment. For wind tunnels which employ large contraction ratio inlets, this lack of understanding is not serious since the relatively low velocity of the flow through the inlet treatment reduces the sensitivity to improper inlet design. When designing a small contraction ratio inlet, much more careful design is needed in order to reduce the flow distortions generated by the inlet treatment. As part of the National Full Scale Aerodynamics Complex Modification Project, 2-D computational methods were developed which account for the effect of both inlet screens and guide vanes on the test section velocity distribution. Comparisons with experimental data are presented which indicate that the methods accurately compute the flow distortions generated by a screen in a nonuniform velocity field. The use of inlet guide vanes to eliminate the screen induced distortion is also demonstrated both computationally and experimentally. Extensions of the results to 3-D is demonstrated and a successful wind tunnel design is presented.

Ross, James C.↗

NASA NTRS1988

Inlet development for the NFAC 80- by 120-foot indraft wind tunnel

This paper describes the inlet design requirements of the National Full-Scale Aerodynamic Complex (NFAC), a closed-loop 4-by-80 foot wind tunnel and indraft 80-by-120 foot wind tunnel. The requirements are based upon desired test section flow quality, atmospheric wind isolation, and noise attenuation. An aerodynamic design study of the inlet treatment is described along with the analysis method and the small-scale testing program used. Measurements taken in the full-scale facility are presented, and the flow quality is summarized. The results are compared with theoretical predictions and small-scale model results.

Van Aken, Johannes M.↗

NASA NTRS1987

Application of a panel method to wake-vortex/wing interaction and comparison with experimental data

The ability of the Vortex Separation AEROdynamics (VSAERO) program to calculate aerodynamic loads on wings due to interaction with free vortices was studied. The loads were calculated for various positions of a downstream following wing relative to an upstream vortex-generating wing. Calculated vortex-induced span loads, rolling-moment coefficients, and lift coefficients on the following wing were compared with experimental results of McMillan et al. and El-Ramly et al. Comparisons of calculated and experimental vortex tangential velocities were also made.

Smith, Brian E.↗

NASA NTRS1987

Time-averaged aerodynamic loads on the vane sets of the 40- by 80-foot and 80- by 120-foot wind tunnel complex

Time-averaged aerodynamic loads are estimated for each of the vane sets in the National Full-Scale Aerodynamic Complex (NFAC). The methods used to compute global and local loads are presented. Experimental inputs used to calculate these loads are based primarily on data obtained from tests conducted in the NFAC 1/10-Scale Vane-Set Test Facility and from tests conducted in the NFAC 1/50-Scale Facility. For those vane sets located directly downstream of either the 40- by 80-ft test section or the 80- by 120-ft test section, aerodynamic loads caused by the impingement of model-generated wake vortices and model-generated jet and propeller wakes are also estimated.

Aoyagi, Kiyoshi↗

NASA NTRS1986

A new design concept for indraft wind-tunnel inlets with application to the national full-scale aerodynamic complex

The present inlet design concept for an indraft wind tunnel, which is especially suited to applications for which a specific test section flow quality is required with minimum inlet size, employs a cascade or vaneset to control flow at the inlet plane, so that test section total pressure variation is minimized. Potential flow panel methods, together with empirical pressure loss predictions, are used to predict inlet cascade performance. This concept has been used to develop an alternative inlet design for the 80 x 120-ft wind tunnel at NASA Ames Research Center. Experimental results show that a short length/diameter ratio wind tunnel inlet furnishing atmospheric wind isolation and uniform test section flow can be designed.

Ross, James C.↗