Engineering topics
Publications and source records attributed to Rosenthal, L. A..
A ballast circuit employing a constant current diode and a vacuum tube that can provide a constant current over a voltage range of 1000 volts. The simple circuit can prove useful in studying voltage breakdown characteristics.
A novel method for testing electroexplosive devices is proposed wherein capacitor discharge pulses, with increasing energy in a step-wise fashion, are delivered to the device under test. The size of the energy increment can be programmed so that firing takes place after many, or after only a few, steps. The testing cycle is automatically terminated upon firing. An energy-firing contour relating the energy required to the programmed step size describes the single-pulse firing energy and the possible sensitization or desensitization of the explosive device.
An electroexplosive device accepts electrical energy and converts it into heat which is used to initiate a primary explosion. Disadvantages of the current electroexplosive testing method have led to the development of a new testing procedure which is based on a principle of programmed pulsing to initiation. A series of stepwise increasing energy pulses is applied to the device which is tested until the initiation of the explosion occurs. The test principle is discussed along with the design of the apparatus.
Heat flow from an embedded heated wire responds to a change in the ambient environment. The wire is part of a self-balancing bridge system, and heat flow is measured directly in watts. Steady-state and transient thermal coupling can be measured directly and is an indication of the thermal resistance and diffusivity for the system under study. The method is applied to an aerospace electroexplosive component.
Many of the fundamental factors affecting the initiation of electroexplosive devices have not been satisfactorily explained. A description of a narrow, high current pulse generator capable of pulses 4 microseconds wide and 94 amperes is given which will be useful in the study of the initiation mechanism.
Electrothermal behavior of bridgewire-explosive interface is defined by pulsing electroexplosive device with a safe level of current and examining the resistance variation of bridgewire. Bridgewire provides signal which describes average wire temperature and heat sinking to the explosive and enclosure.
By terminating the discharge of energy into an insensitive electroexplosive device, firing-energy parameters can be determined. A simple capacitor-discharge system providing exponential pulses terminated at an adjustable width is described. Basic theory and application to testing are discussed.
Several nondestructive test techniques were developed for electroexplosive devices. The bridgewire responds, when pulsed with a safe level current, by generating a characteristic heating curve. The response is indicative of the electrothermal behavior of the bridgewire-explosive interface. Bridgewires which deviate from the characteristic heating curve were dissected and examined to determine the cause of the abnormality. Deliberate faults were fabricated into squibs. The relationship of the specific abnormality and the fault associated with it is demonstrated.
A self-balancing bridge for ascertaining the electrothermal and nonlinear behavior of an electroexplosive device is described. A sinusiodal current is passed through the device which provides a signal in the form of a unique Lissajous display. The display can be qualitatively evaluated and abnormal units can be readily detected.
Half-sine wave pulse firing of electroexplosive devices
Terminated capacitor discharge firing of electroexplosive devices
The firing characteristics of insensitive electroexplosive devices to certain impulsive waveforms have been investigated. For these waveforms, energy is delivered in a time short compared to the thermal time constant and therefore cooling plays a negligible role. One waveform is a terminated capacitor discharge wherein the regular discharge of a capacitor is terminated at a preset point. Another is a half-sine wave pulse. The theory, design, and application of both impulsive waveform generators are presented together with certain limited experimental observations.
Several nondestructive test techniques have been developed for electroexplosive devices. The bridgewire will respond, when pulsed with a safe level current, by generating a characteristic heating curve. The response is indicative of the electrothermal behavior of the bridgewire-explosive interface. Bridgewires which deviate from the characteristic heating curve have been dissected and examined to determine the cause for the abnormality. Deliberate faults have been fabricated into squibs. The relationship of the specific abnormality and the fault associated with it is discussed.
Nondestructive testing of insensitive electroexplosive devices by transient techniques