Engineering topics

Rose, William C.

Publications and source records attributed to Rose, William C..

14 records

NASA NTRS2011

Grid Fin Stabilization of the Orion Launch Abort Vehicle

Wind tunnel tests were conducted by Nielsen Engineering & Research (NEAR) and Rose Engineering & Research (REAR) in conjunction with the NASA Engineering & Safety Center (NESC) on a 6%-scale model of the Orion launch abort vehicle (LAV) configured with four grid fins mounted near the base of the vehicle. The objectives of these tests were to 1) quantify LAV stability augmentation provided by the grid fins from subsonic through supersonic Mach numbers, 2) assess the benefits of swept grid fins versus unswept grid fins on the LAV, 3) determine the effects of the LAV abort motors on grid fin aerodynamics, and 4) generate an aerodynamic database for use in the future application of grid fins to small length-to-diameter ratio vehicles similar to the LAV. The tests were conducted in NASA Ames Research Center's 11x11-foot transonic wind tunnel from Mach 0.5 through Mach 1.3 and in their 9x7-foot supersonic wind tunnel from Mach 1.6 through Mach 2.5. Force- and moment-coefficient data were collected for the complete vehicle and for each individual grid fin as a function of angle of attack and sideslip angle. Tests were conducted with both swept and unswept grid fins with the simulated abort motors (cold jets) off and on. The swept grid fins were designed with a 22.5deg aft sweep angle for both the frame and the internal lattice so that the frontal projection of the swept fins was the same as for the unswept fins. Data from these tests indicate that both unswept and swept grid fins provide significant improvements in pitch stability as compared to the baseline vehicle over the Mach number range investigated. The swept fins typically provide improved stability as compared to the unswept fins, but the performance gap diminished as Mach number was increased. The aerodynamic performance of the fins was not observed to degrade when the abort motors were turned on. Results from these tests indicate that grid fins can be a robust solution for stabilizing the Orion LAV over a wide range of operating conditions.

Pruzan, Daniel A.↗

NASA NTRS1995

Application of CFD to the analysis and design of high-speed inlets

Over the past seven years, efforts under the present Grant have been aimed at being able to apply modern Computational Fluid Dynamics to the design of high-speed engine inlets. In this report, a review of previous design capabilities (prior to the advent of functioning CFD) was presented and the example of the NASA 'Mach 5 inlet' design was given as the premier example of the historical approach to inlet design. The philosophy used in the Mach 5 inlet design was carried forward in the present study, in which CFD was used to design a new Mach 10 inlet. An example of an inlet redesign was also shown. These latter efforts were carried out using today's state-of-the-art, full computational fluid dynamics codes applied in an iterative man-in-the-loop technique. The potential usefulness of an automated machine design capability using an optimizer code was also discussed.

Rose, William C.↗

NASA NTRS1993

Numerical investigations in three-dimensional internal flows

In the present reporting period, the 3D STUFF code was used to solve the underbody flow for the waverider configuration vehicle. In order to start the space-marched version of the code, the time-marched version (TUFF) was used to solve the forward portion of the underside of the forebody flowfield. A grid was generated which went from the tip of the nose to the location of the cowl lip. This includes all of the inlet ramp system. Previous indications were that three-dimensional effects could be expected on the ramps of such an aircraft. For purposes of the present study, no sidewalls were assumed. The sidewalls were eliminated to simplify the calculations and to show the potential effects of three-dimensional flow in the absence of a full sidewall. Further, this flow was also analyzed using the newly released OVERFLOW code and comparisons between the two codes were made. In addition to these 3D calculations, 2D calculations using the OVERFLOW code were also obtained for the Mach 5 inlet model in this reporting period. Comparisons between the experimental data, previous computational fluid dynamics (CFD) results and those from OVERFLOW were made.

Rose, William C.↗

NASA NTRS1993

Numerical investigations in three-dimensional internal flows

In the present reporting period, the 3D version of the OVERFLOW code was used to solve the flow within the internal portion of the supersonic inlet. The internal portion of this inlet is bounded by an inflow plane containing the leading edge of the sidewalls, the sidewalls, the ramp and cowl surfaces and an outflow plane just downstream of the minimum geometric area of the inlet. Boundary layer bleed was used in the two-dimensional calculations discussed in the previous progress report and that same bleed was applied in the present study. For reference, this bleed corresponds to locations designated as R2 and R3 in the Mach 5 inlet model test. Using the GRIDGEN code, a three dimensional grid was generated that accounted for the viscous effects expected to occur on the sidewall, as well as those known to occur on the ramp and cowl surfaces. The internal flow grid size was 141 streamwise by 101 cross stream by 71 in the lateral direction between sidewalls. Since the flow entering the inlet was not symmetrical, the inlet was solved from sidewall to sidewall (without using a symmetry plane). In addition to the short sidewalls proposed in the Langley geometry database, a set of shorter sidewalls was also investigated in the present study and was shown to have beneficial effects with respect to the flow distortion exiting the supersonic inlet. In addition to these calculations, additional 3D solutions using the OVERFLOW code were obtained for the flow downstream of the throat of the supersonic inlet, including a terminal shock wave system produced by a backpressured subsonic diffuser.

Rose, William C.↗

NASA NTRS1991

Numerical investigations in three-dimensional internal flows

The present study is a preliminary investigation into the behavior of the flow within a 28 degree total geometric turning angle hypothetical Mach 10 inlet as calculated with the full three-dimensional Navier-Stokes equations. Comparison between the two-dimensional and three-dimensional solutions have been made. The overall compression is not significantly different between the two-dimensional and center plane three dimensional solutions. Approximately one-half to two-thirds of the inlet flow at the exit of the inlet behave nominally two-dimensionally. On the other hand, flow field non-uniformities in the three-dimensional solution indicate the potential significance of the sidewall boundary layer flows ingested into the inlet. The tailoring of the geometry at the inlet shoulder and on the cowl obtained in the two-dimensional parametric design study have also proved to be effective at controlling the boundary layer behavior in the three-dimensional code. The three-dimensional inlet solution remained started indicating that the two-dimensional design had a sufficient margin to allow for three-dimensional flow field effects. Although confidence is being gained in the use of SCRAM3D (three-dimensional full Navier-Stokes code) as applied to similar flow fields, the actual effects of the three-dimensional flow fields associated with sidewalls and wind tunnel installations can require verification with ground-based experiments.

Rose, William C.↗

NASA NTRS1991

Numerical investigations in three-dimensional internal flows

In previous efforts, a two-dimensional full Navier-Stokes (FNS) code (SCRAM2D) was used in a design process that involved parametric modifications of the inlet geometry to arrive at what appeared to be an optimum inlet flowfield that produced a uniform flow at the exit in a very short distance. In these previous studies, the technologies for determining the contours with a 'man-in-the-loop' approach for both the ramp and cowl of the inlet were demonstrated, and nearly shock-free exiting flowfields were shown to be obtainable. The resulting two-dimensional compression contours were then used with swept sidewalls to form a three-dimensional inlet. Then the three-dimensional Navier-Stokes code (SCRAM3D) was used to investigate the inlet's three-dimensional flow. One of the major difficulties encountered in the previous studies was that associated with the relatively long time required to obtain a solution using even the 2D FNS code in the design process. Since one of the goals of high-speed inlet design is to produce inputs to the overall aircraft design in a timely manner, it was proposed for this year's research to examine 2D and 3D viscous flow solver techniques alternative to the NFS codes used to date. Areas of the inlet particularly identified for code speed up are those associated with the forebody and external flow ramp systems of the inlet. In these areas, parabolized, or space-marched, Navier-Stokes codes were proposed to be investigated for their applicability in the design process developed previously. This report describes the results of an investigation into the use of two other codes for analyzing the forebody and inlet ramp systems of high-speed inlets.

Rose, William C.↗

NASA NTRS1991

Numerical investigations in three-dimensional internal flows

The general objectives of NASA's Generic Hypersonics Research Program (GHP) are to develop a technology background required for aeronautical research in the hypersonic Mach number flow range. These research efforts are to complement the National Aerospace Plane (NASP) Program and are geared toward the development of experimental and computational fluid dynamics (CFD) techniques. One of the prominent goals of inlet design for high speed applications is to produce an inlet that delivers uniform flow at its exit in the shortest possible distance. In previous studies, the technologies for determining contours for both the ramp and cowl were demonstrated that allowed a nearly shock free exiting flow field to be obtained. This technology was developed further during the present reporting period and applied to a preliminary design investigation of a biconic hypersonic research vehicle with a nearly 2-D inlet attached near the aft end of the vehicle. The results of a parametric investigation of this proposed inlet for freestream Mach numbers between 10 and 15 are described.

Rose, William C.↗

NASA NTRS1990

Numerical investigations in three-dimensional internal flows

The application of the SCRAM2D code to investigating the flow fields that might be expected to occur in a representative Mach 10, two dimensional (ramp-compression) inlet is described. This Mach number allows the use of existing Navier-Stokes codes without the additional complexity of air chemistry and the associated large increases in computational time required to achieve numerical simulations of such flow fields. The CFD simulation consists of a two-dimensional inlet geometry that has an overall geometric turning of 36 degrees. The cowl for this inlet is assumed to be aligned with the oncoming freestream flow, turning the ramp flow field back parallel to the freestream, thus producing the overall 36 degree turning angle. The primary subject is the cowl shock wave-ramp boundary layer interaction effects. The results of numerical simulations carried out at the design Mach number of 10 and two other off-design Mach numbers, 7.2 and 5.0 are described.

Rose, William C.↗

NASA NTRS1990

Numerical investigations in three-dimensional internal flows

The flow in the transonic test facility was investigated using the three dimensional computational fluid dynamics techniques. The application of the full Navier-Stokes three dimensional code to the flow qualities in the contraction section of transonic wind tunnel is discussed. Initially, two dimensional solutions indicated the possibility for large secondary flow to exist as a result of the asymmetries involved in the contraction section as it is constructed. The results of a full three dimensional solution indicate that only minor pressure variations actually occur in the contraction section within any given cross flow plane. Further analysis of the three dimensional solution indicated that these slight lateral pressure gradients lead to negligible secondary flows, except within a small region in the corners within the boundary layer. On the basis of present solution, it would not be expected that any flow asymmetries and/or secondary flow present within contraction section are associated with the methods by which the contraction is implemented in its present configuration.

Rose, William C.↗

NASA NTRS1988

Numerical investigations in three-dimensional internal flows

In order to develop an understanding of flow fields that exist in sidewall compression inlet models, an explicit, time-accurate full Navier-Stokes code was used to model them. Both laminar and turbulent boundary layers were numerically simulated. These simulations were examined as they were influenced by Mach number, changes in sidewall compression angle, hypersonic viscous interaction effects, and thick entering boundary layers. Cause and effect relationships were established. The numerical simulations were compared with the limited data available to aid in understanding both the simulations and the experiments.

Rose, William C.↗

NASA NTRS1988

Numerical investigations in three-dimensional internal flows

Renewed interest in simulation of high enthalpy flows was brought about by interest in the design and testing of hypersonic propulsion components. This renewed interest has led to refurbishment of high speed ground based wind tunnel facilities. Simulation of the high enthalpy flows occurring in the NASP propulsion system is of particular interest. Studying the combustor presentes some of the more challenging problems in the ground based simulation of the fluid flow. A difficulty in simulating the required conditions at the entrance to the combustor is related to achieveing a sufficiently high static pressure such that combustion would be possible at a high Mach number. An analysis of the flow within the original nozzle was not performed previously using numerical simulations, although it was operated experimentally. A Navier-Stokes code was chosen in the present study to examine analytically the flow within representative selected nozzles for use in combustion experiments. The numerical simulation of these fluid flows is popular and may be able to shed light on the direction that redesign of the shock tube nozzles should take. The numerical codes were modified to account for the axially symmetric flow field, for the inclusion of equilibrium real gas effects and for ideal gases whose thermodynamic properties are frozen at the stagnation conditions. Numerical simulation of flows within the original and two proposed nozzles, including the energy lost to the relatively cold walls, are investigated.

Rose, William C.↗

NASA NTRS1988

Aerodynamics of Seeing on Large Transport Aircraft

Efforts were undertaken to obtain a set of data that examined the level of turbulence and the scale sizes in the shear layer existing over the fence quieted cavity on the NASA-Ames Kuiper Airborne Observatory (KAO). These data were to be taken during the present study and compared with data taken from previous wind tunnel experiments, for which both aerodynamic and direct optical measurements were made. The data obtained during the present study were presented and discussed in light of their impact on the quality of optical images, that is, seeing through the shear layer. In addition, scaling relationships were presented that allow optical data obtained in one aerodynamic environment to be estimated for another one at perhaps different Mach numbers, scale sizes, or aircraft configurations.

Rose, William C.↗

NASA NTRS1988

Numerical investigations in three-dimensional internal flows

An investigation into the use of computational fluid dynamics (CFD) was performed to examine the expected heat transfer rates that will occur within the NASA-Ames 100 megawatt arc heater nozzle. This nozzle was tentatively designed and identified to provide research for a directly connected combustion experiment specifically related to the National Aerospace Plane Program (NASP) aircraft, and is expected to simulate the flow field entering the combustor section. It was found that extremely fine grids, that is very small mesh spacing near the wall, are required to accurately model the heat transfer process and, in fact, must contain a point within the laminar sublayer if results are to be taken directly from a numerical simulation code. In the present study, an alternative to this very fine mesh and its attendant increase in computational time was invoked and is based on a wall-function method. It was shown that solutions could be obtained that give accurate indications of surface heat transfer rate throughout the nozzle in approximately 1/100 of the computer time required to do the simulation directly without the use of the wall-function implementation. Finally, a maximum heating value in the throat region of the proposed slit nozzle for the 100 megawatt arc heater was shown to be approximately 6 MW per square meter.

Rose, William C.↗

NASA NTRS1977

Turbulence Measurement in Transonic Flow

Two instrumentation systems are presently practical to use in turbulence measurements. The laser velocimeter can measure fluctuating velocities while the hot-wire anemometer, in principle, can be used to obtain both kinematic and thermodynamic fluctuations. In addition, the hot-wire anemometer gives an analog signal output that is convenient for use in time-space correlation studies and spectral analyses. The laser velocimeter has been used successfully in all flow regimes, whereas the hot wire has not been exploited in transonic flows, where the wire response has not been well-understood. The purpose of this Note is to examine the response and calibration of a constant-temperature, hot- wire anemometer in transonic flow and to present turbulence measurements, obtained in a transonic boundary layer.

Rose, William C.↗