Engineering topics

Roithmayr, Carlos M.

Publications and source records attributed to Roithmayr, Carlos M..

At least 19 records

NASA NTRS2019

Application of System Identification to Parachute Modeling

Parachute models are used in numerous flight simulation tools to predict a wide range of parachute flight performance characteristics (e.g., parachute inflation loads, parachute stability and dynamics, vehicle touchdown conditions, and, ultimately, the safety and survivability of the system using the parachute). The current state of the art in developing parachute models is to initially estimate the parachute characteristics based on the parachute geometry and historical data and then add increased model fidelity based on data from wind tunnel and/or flight tests. This approach, however, can be deficient in identifying which parachute states (e.g., angle of attack, sideslip, angular rates, flyout angles, descent rate, dynamic pressure, proximity to other parachutes) are responsible for the parachute motion, and the relationship between those states and the forces on the parachute.

Murri, Daniel G.↗

NASA NTRS2019

Application of System Identification to Parachute Modeling

A series of exact analytical solutions is developed for a capsule with two parachutes to verify CAPDYN and FAST results for terminal conditions. The case described herein is for the capsule and two parachutes acting as a fixed system in terminal descent. In this simplest case, the density is modeled as a constant defined by the initial release altitude. The analytical solution predicts the system terminal dynamic pressure, velocity, and altitude for comparison with CAPDYN and FAST simulation results.

Murri, Daniel G.↗

NASA NTRS2019

Linear Analysis of a Two-Parachute System Undergoing Pendulum Motion

Motion resembling that of a pendulum undergoing large-amplitude oscillation was ob- served during a series of flight tests of an unoccupied Orion Capsule Parachute Assembly System (CPAS) drop-test vehicle. Large excursions away from vertical by the capsule could cause it to strike the ground or ocean at a large angle with respect to vertical, with an undesirable attitude with respect to heading, or with a large horizontal or vertical speed. These conditions are to be avoided because they would endanger the occupants of the capsule in an actual mission. Pendulum motion is intimately related to a parachute’s aerodynamic normal force coefficient, which is a nonlinear function of angle of attack. An analytical investigation of the dynamics of pendulum motion is undertaken with the aid of a simplified model of the physical system and the assumption that the normal force coefficient is a linear function of angle of attack in the neighborhood of a value corresponding to stable equilibrium. The analysis leads to a simple relationship for the location of a pivot point, which provides insights that are consistent with previous studies.

Roithmayr, Carlos M.↗

NASA NTRS2019

Modal Analysis of a Two-Parachute System

The Orion capsule is designed to land under a nominal configuration of three main parachutes; however, the system is required to be fault tolerant and land successfully if one of the main parachutes fails to open. The Capsule Parachute Assembly System (CPAS) Team performed a series of drop tests in order to characterize the performance of the system with two main parachutes. During the series of drop tests, several distinct dynamical modes were observed. The most consequential of these is the pendulum mode. Three other modes are benign: flyout (scissors), maypole, and breathing. The actual multi-body system is nonlinear, flexible, and possesses significant cross-coupling. Rather than perform analysis of this highly complex system directly, we conduct analysis of each dynamical mode observed during flight, based on first principles. This approach is analogous to traditional aircraft flight dynamics analysis in which the full nonlinear behavior of the airframe is decomposed into longitudinal dynamics (phugoid and short-period modes) and lateral dynamics (spiral, roll-subsidence, and dutch-roll modes). This analysis is intended to supplement multi-body nonlinear simulations in order to provide further insight into the system.

Pei, Jing↗

NASA NTRS2018

Dynamics and Control of a Tethered Enhanced Gravity Tractor Performing Asteroid Deflection

The dynamics and control of an Enhanced Gravity Tractor (EGT) augmented with a tether for deflecting an asteroid are studied. A conventional EGT consists of collected asteroidal mass collocated with the spacecraft. Because of the presence of a tether, the collected mass is placed where the EGT would have been without a tether, and the spacecraft is placed farther away from the asteroid. Doing so improves the fuel efficiency and safety margin of the EGT operation without significantly sacrificing the gravitational attraction between the asteroid and the EGT. The tether is modeled as a series of particles connected by spring-dashpot systems. Physical properties of the tether are selected to be similar to those of the SPECTRA-1000, Kevlar-29, and Kevlar-49 fibers. It is assumed that control is applied only to the spacecraft, and there is no active control associated with the collected mass. A Proportional-Derivative (PD) controller is employed to maintain the spacecraft and the collected mass at desired positions relative to the asteroid. Numerical simulations of tethered EGT operations at 2008 EV5, Itokawa, Apophis, and a fictitious ellipsoidal asteroid are performed. It is demonstrated that a PD controller is capable of accomplishing the control objectives. The gravity gradient and the control force keep the tether stretched throughout a normal tethered EGT operation, and the load on the tether is well within the design limit of the tether material. While including multiple particles in the tether model is essential in capturing details of tether vibration, the number of particles does not significantly affect the motions of the collected mass and the spacecraft. In addition, the distance from the asteroid mass center to the collected mass should be chosen judiciously in the case of a rotating slender asteroid; some distance ranges should be avoided as excessive lateral oscillations can be excited by resonance between the asteroid rotation and tether pendular motion.

Shen, Haijun↗

NASA NTRS2018

Contributions of Spherical Harmonics to Gravitational Moment

A scalar gravitational potential function expressed as a series of spherical harmonics frequently serves as the basis for a model of an astronomical body's gravitational field. The contribution of a generic spherical harmonic to gravitational gradient is expressed as a dyadic, which is then used to obtain an analytical expression in vector-dyadic form for the contribution to the moment of gravitational forces about the mass center of a small body such as a spacecraft. The expression developed for a harmonic's contribution to gravitational gradient can be applied in areas beyond the scope of the paper; for example, gravitational gradient plays an important role in the state propagation matrix and the state transition matrix that are used in spacecraft trajectory targeting and Kalman filtering. Additionally, it can be employed in numerical simulations of orbit determination based on measurements obtained with a gradiometer in low-Earth orbit. Contributions of spherical harmonics to gravitational moment may be of interest in connection with attitude control of a spacecraft in the vicinity of a body with an irregular shape, such as an asteroid. Normalized spherical harmonic coefficients up to degree and order 10 are obtained for the asteroid 216 Kleopatra and used in numerical evaluations of contributions to gravitational moment.

Roithmayr, Carlos M.↗

NASA NTRS2016

Development of Constraint Force Equation Methodology for Application to Multi-Body Dynamics Including Launch Vehicle Stage Seperation

The objective of this report is to develop and implement a physics based method for analysis and simulation of multi-body dynamics including launch vehicle stage separation. The constraint force equation (CFE) methodology discussed in this report provides such a framework for modeling constraint forces and moments acting at joints when the vehicles are still connected. Several stand-alone test cases involving various types of joints were developed to validate the CFE methodology. The results were compared with ADAMS(Registered Trademark) and Autolev, two different industry standard benchmark codes for multi-body dynamic analysis and simulations. However, these two codes are not designed for aerospace flight trajectory simulations. After this validation exercise, the CFE algorithm was implemented in Program to Optimize Simulated Trajectories II (POST2) to provide a capability to simulate end-to-end trajectories of launch vehicles including stage separation. The POST2/CFE methodology was applied to the STS-1 Space Shuttle solid rocket booster (SRB) separation and Hyper-X Research Vehicle (HXRV) separation from the Pegasus booster as a further test and validation for its application to launch vehicle stage separation problems. Finally, to demonstrate end-to-end simulation capability, POST2/CFE was applied to the ascent, orbit insertion, and booster return of a reusable two-stage-to-orbit (TSTO) vehicle concept. With these validation exercises, POST2/CFE software can be used for performing conceptual level end-to-end simulations, including launch vehicle stage separation, for problems similar to those discussed in this report.

Pamadi, Bandu N.↗

NASA NTRS2015

Towing Asteroids with Gravity Tractors Enhanced by Tethers and Solar Sails

Material collected from an asteroid's surface can be used to increase gravitational attraction between the asteroid and a Gravity Tractor (GT); the spacecraft therefore operates more effectively and is referred to as an Enhanced Gravity Tractor (EGT). The use of tethers and solar sails to further improve effectiveness and simplify operations is investigated. By employing a tether, the asteroidal material can be placed close to the asteroid while the spacecraft is stationed farther away, resulting in a better safety margin and improved thruster efficiency. A solar sail on a spacecraft can naturally provide radial offset and inter-spacecraft separation required for multiple EGTs.

Shen, Haijun↗

NASA NTRS2014

Controlled Ascent From the Surface of an Asteroid

The National Aeronautics and Space Administration (NASA) is currently investigating a conceptual robotic mission to collect a small boulder up to 4 m in diameter resting on the surface of a large Near Earth Asteroid (NEA). Because most NEAs are not well characterized, a great range of uncertainties in boulder mass properties and NEA surface characteristics must be considered in the design of this mission. These uncertainties are especially significant when the spacecraft ascends with the boulder in tow. The most important requirement during ascent is to keep the spacecraft in an upright posture to maintain healthy ground clearances for the two large solar arrays. This paper focuses on the initial stage (the first 50 m) of ascent from the surface. Specifically, it presents a sensitivity study of the solar array ground clearance, control authority, and accelerations at the array tips in the presence of a variety of uncertainties including various boulder sizes, densities, shapes and orientations, locations of the true center of mass, and push-off force distributions. Results are presented, and appropriate operations are recommended in the event some of the off-nominal cases occur.

Shen, Haijun↗

NASA NTRS2014

Design Considerations for Miniaturized Control Moment Gyroscopes for Rapid Retargeting and Precision Pointing of Small Satellites

This paper presents the design as well as characterization of a practical control moment gyroscope (CMG) based attitude control system (ACS) for small satellites in the 15-20 kilogram mass range performing rapid retargeting and precision pointing maneuvers. The paper focuses on the approach taken in the design of miniaturized CMGs while considering the constraints imposed by the use of commercial off-the-shelf (COTS) components as well as the size of the satellite. It is shown that a hybrid mode is more suitable for COTS based moment exchange actuators; a mode that uses the torque amplification of CMGs for rapid retargeting and direct torque capabilities of the flywheel motors for precision pointing. A simulation is provided to demonstrate on-orbit slew and pointing performance.

Patankar, Kunal↗

NASA NTRS2014

Co-Spin With Symmetry Axis Stabilization, and De-Spin for Asteroid Capture

Consideration is given to attitude control associated with capturing a free-flying asteroid using an axisymmetric spacecraft. Asymptotically stable controllers are designed to align the spacecraft axis of symmetry with a line of descent that is fixed in the asteroid, and to eliminate all relative angular velocity before capture takes place. An analytical expression is presented for the torque required to maintain alignment of the axes of symmetry of the spacecraft and an axisymmetric asteroid. After the asteroid is securely captured, the angular velocity of the rigid composite body relative to an inertial frame is arrested; we present a controller that is asymptotically stable and stays within specified thrust limits.

Shen, Haijun↗

NASA NTRS2013

Catching a Rolling Stone: Dynamics and Control of a Spacecraft and an Asteroid

In a recent report, a robotic spacecraft mission is proposed for the purpose of collecting a small asteroid, or a small part of a large one, and transporting it to an orbit in the Earth-Moon system. Such an undertaking will require solutions to many of the engineering problems associated with deflection of an asteroid that poses a danger to Earth. In both cases, it may be necessary for a spacecraft to approach an asteroid from a nearby position, hover for some amount of time, move with the same angular velocity as the asteroid, descend, perhaps ascend, and finally arrest the angular velocity of the asteroid. Dynamics and control in each of these activities is analyzed in order to determine the velocity increments and control torque that must be provided by a reaction control system, and the mass of the propellant that will be consumed. Two attitude control algorithms are developed, one to deal with synchronizing the spacecraft s angular velocity with that of the asteroid, and the other to arrest the asteroid s angular velocity. A novel approach is proposed for saving fuel in the latter case.

Roithmayr, Carlos M.↗

NASA NTRS2012

Analysis of Opportunities for Intercalibration Between Two Spacecraft

There is currently a strong interest in obtaining highly accurate measurements of solar radiation reflected by Earth. For example, the Traceable Radiometry Underpinning Terrestrial- and Helio- Studies (TRUTHS) satellite mission has been under consideration in Europe for several years, and planning is now under way for the Climate Absolute Radiance and Refractivity Observatory (CLARREO) spacecraft in the United States. Such spacecraft will provide measurements whose high accuracy is traceable to SI standards; these measurements will be useful as a reference for calibrating similar instruments on board other spacecraft. Hence, analysis of opportunities for intercalibration between two spacecraft plays an important role in the planning of future missions. In order for intercalibration to take place, the measurements obtained from two spacecraft must have similar viewing geometry and be taken within a few minutes of one another. Viewing geometry is characterized in terms of viewing zenith angle, solar zenith angle, and relative azimuth angle. Opportunities for intercalibration are greater in number and longer in duration if the sensor with high accuracy can be aimed at points on the surface of the Earth other than the nadir or sub-satellite point. Analysis of intercalibration over long periods is rendered tractable by making several simplifying assumptions regarding orbital motions of the two spacecraft about Earth, as well as Earth s orbit about the Sun. The shape of the Earth is also considered. A geometric construction called a tent is introduced to facilitate analysis. It is helpful to think of an intercalibration opportunity as the passage of one spacecraft through a tent that has a fixed shape and moves with the spacecraft whose measurements are to be calibrated. Selection of points on Earth s surface as targets for measurement is discussed, as is aiming the boresight of a steerable instrument. Analysis results for a pair of spacecraft in typical low Earth orbits are provided.

Roithmayr, Carlos M.↗

NASA NTRS2011

Modeling Multibody Stage Separation Dynamics Using Constraint Force Equation Methodology

This paper discusses the application of the constraint force equation methodology and its implementation for multibody separation problems using three specially designed test cases. The first test case involves two rigid bodies connected by a fixed joint, the second case involves two rigid bodies connected with a universal joint, and the third test case is that of Mach 7 separation of the X-43A vehicle. For the first two cases, the solutions obtained using the constraint force equation method compare well with those obtained using industry- standard benchmark codes. For the X-43A case, the constraint force equation solutions show reasonable agreement with the flight-test data. Use of the constraint force equation method facilitates the analysis of stage separation in end-to-end simulations of launch vehicle trajectories

Tartabini, Paul V.↗

NASA NTRS2010

Forces Associated with Nonlinear Nonholonomic Constraint Equations

A concise method has been formulated for identifying a set of forces needed to constrain the behavior of a mechanical system, modeled as a set of particles and rigid bodies, when it is subject to motion constraints described by nonholonomic equations that are inherently nonlinear in velocity. An expression in vector form is obtained for each force; a direction is determined, together with the point of application. This result is a consequence of expressing constraint equations in terms of dot products of vectors rather than in the usual way, which is entirely in terms of scalars and matrices. The constraint forces in vector form are used together with two new analytical approaches for deriving equations governing motion of a system subject to such constraints. If constraint forces are of interest they can be brought into evidence in explicit dynamical equations by employing the well-known nonholonomic partial velocities associated with Kane's method; if they are not of interest, equations can be formed instead with the aid of vectors introduced here as nonholonomic partial accelerations. When the analyst requires only the latter, smaller set of equations, they can be formed directly; it is not necessary to expend the labor to form the former, larger set first and subsequently perform matrix multiplications.

Roithmayr, Carlos M.↗

NASA NTRS2009

Developments to Increase the Performance, Operational Versatility and Automation of a Lunar Surface Manipulation System

The objective of this paper is to describe and summarize the results of the development efforts for the Lunar Surface Manipulation System (LSMS) with respect to increasing the performance, operational versatility, and automation. Three primary areas of development are covered, including; the expansion of the operational envelope and versatility of the current LSMS test-bed, the design of a second generation LSMS, and the development of automation and remote control capability. The first generation LSMS, which has been designed, built, and tested both in lab and field settings, is shown to have increased range of motion and operational versatility. Features such as fork lift mode, side grappling of payloads, digging and positioning of lunar regolith, and a variety of special end effectors are described. LSMS operational viability depends on bei nagble to reposition its base from an initial position on the lander to a mobility chassis or fixed locations around the lunar outpost. Preliminary concepts are presented for the second generation LSMS design, which will perform this self-offload capability. Incorporating design improvements, the second generation will have longer reach and three times the payload capability, yet it will have approximately equivalent mass to the first generation. Lastly, this paper covers improvements being made to the control system of the LSMS test-bed, which is currently operated using joint velocity control with visual cues. These improvements include joint angle sensors, inverse kinematics, and automated controls.

Dorsey, John T.↗

NASA NTRS2009

Application of CFE/POST2 for Simulation of Launch Vehicle Stage Separation

The constraint force equation (CFE) methodology provides a framework for modeling constraint forces and moments acting at joints that connect multiple vehicles. With implementation in Program to Optimize Simulated Trajectories II (POST 2), the CFE provides a capability to simulate end-to-end trajectories of launch vehicles, including stage separation. In this paper, the CFE/POST2 methodology is applied to the Shuttle-SRB separation problem as a test and validation case. The CFE/POST2 results are compared with STS-1 flight test data.

Pamadi, Bandu N.↗

NASA NTRS2009

Automation of a Versatile Crane (the LSMS) for Lunar Outpost Construction, Maintenance and Inspection

Devices for lifting, translating and precisely placing payloads are critical for efficient Earth-based construction operations. Both recent and past studies have demonstrated that devices with similar functionality will be needed to support lunar outpost operations. Although several designs have been developed for Earth based applications, these devices lack unique design characteristics necessary for transport to and use on the harsh lunar surface. These design characteristics include: a) lightweight components, b) compact packaging for launch, c) automated deployment, d) simple in-field reconfiguration and repair, and e) support for tele-operated or automated operations. Also, because the cost to transport mass to the lunar surface is very high, the number of devices that can be dedicated to surface operations will be limited. Thus, in contrast to Earth-based construction, where many single-purpose devices dominate a construction site, a lunar outpost will require a limited number of versatile devices that provide operational benefit from initial construction through sustained operations. The first generation test-bed of a new high performance device, the Lunar Surface Manipulation System (LSMS) has been designed, built and field tested. The LSMS has many unique features resulting in a mass efficient solution to payload handling on the lunar surface. Typically, the LSMS device mass is estimated at approximately 3% of the mass of the heaviest payload lifted at the tip, or 1.8 % of the mass of the heaviest mass lifted at the elbow or mid-span of the boom for a high performance variant incorporating advanced structural components. Initial operational capabilities of the LSMS were successfully demonstrated during field tests at Moses Lake, Washington using a tele-operated approach. Joint angle sensors have been developed for the LSMS to improve operator situational awareness. These same sensors provide the necessary information to support fully automated operations, greatly expanding the operational versatility of the LSMS. This paper develops the equations describing the forward and inverse relation between LSMS joint angles and Cartesian coordinates of the LSMS tip. These equations allow a variety of schemes to be used to maneuver the LSMS to optimize the maneuver. One such scheme will be described in detail that eliminates undesirable swinging of the payload at the conclusion of a maneuver, even when the payload is suspended from a passive rigid link. The swinging is undesirable when performing precision maneuvers, such as aligning an object for mating or positioning a camera. Use of the equations described here enables automated control of the LSMS greatly improving its operational versatility.

Doggett, William R.↗