Development of 22.5 % p-type tunnel oxide passivated contact solar cells through efficiency enhancement by replacing local Al-BSF in PERC cells with (p+) poly-Si/SiO2 carrier selective contact
Not Available
Choi, Wook-Jin (ORCID:000000032568419X)↗
Engineering topics
Rohatgi, Ajeet
Publications and source records attributed to Rohatgi, Ajeet.
Passivation and Degradation of Sulfur-Treated Silicon Surfaces for Photovoltaics
Sulfur-based passivation for silicon surfaces using H2S gas is an alternative passivation method to reduce the thermal budget for Si photovoltaics. To understand the impact of the high-quality passivation and an observed passivation efficiency decrease after air exposure, we have studied the chemical surface structure by X-ray photoelectron spectroscopy (XPS), X-ray Auger electron spectroscopy (XAES), and S and Si L2,3 X-ray emission spectroscopy (XES). On the S-passivated silicon surfaces, we find the formation of S–Si bonds, in addition to some Si–O bonds. Upon air exposure, sulfur partially desorbs from the Si surface and an increased presence of Si–O and S–O bonds is observed. We identify that well-defined S–Si bonds are crucial to maintain high-quality surface passivation for Si photovoltaics, which allows further optimization of the fabrication process for S-based passivation on silicon.
Hua, Amandee↗
Microscopic and elemental analysis of temperature-induced changes in sulfur/silicon nitride stack-passivated Si surface
Not Available
Mouri, Tasnim Kamal↗
Investigation of Contact Properties and Device Performance for Bifacial Double-Side Textured Silicon Solar Cells With Polysilicon Based Passivating Contacts
We investigate the impact of the surface morphology on the contact properties of phosphorus doped poly-Si layers. If the poly-Si layer on a textured surface remains intact after high-temperature metallization using a fire-through (FT) silver (Ag) paste, the J0,metal is not expected to increase significantly while the specific contact resistivity can improve with a textured surface. The contact properties of the FT Ag contacts to n+ poly-Si deposited on both textured and planar surfaces are investigated by measuring and evaluating ρc and J0,metal. The reasons for differences in contact resistance and recombination are further investigated with SEM imaging. Solar cells with n-type polysilicon based passivating contacts on the rear side are fabricated and characterized. The scientific approach used, and the insights presented in this work, help to understand the mechanisms and behavior of screen-printed and fired-through contacts to polysilicon layers deposited onto textured silicon surfaces.
Padhamnath, Pradeep (ORCID:0000000202510624)↗
Evaluating the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells
A bifacial silicon heterojunction solar cell demands approximately 210 mg usage of silver paste (9 busbars, 24.5%, bifacial, M6 size wafer). Copper is an excellent alternative to silver: 100x cheaper, similar elecvtrical resistivities, and 1000x more abundant. Successful demonstration of large area selective emitter PERC solar cells using Cu fire-through paste with FF approximately 75% and approximately 19%. Paste chemistry results in oxide-based Cu diffusion barrier, leading to good reliability of the devices: 1000h DHT giving a 3.5% efficiency drop. The additional series resistance still needs to be lowered. Printed and fired cell performance is governed mostly by pFF, especially J02 ; same for DHT degradation. Further improvement in printing and firing optimization for lower series resistance and higher FF.
Ag↗
Exploring the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells
For 40 TW of PV required to transition our planet to 100% renewables, the silver (Ag) should disappear from PV production. Advantages of copper (Cu) over silver (Ag) include 1) bulk Cu has a similar conductivity to Ag (1.7 mu O-cm for Cu, 1.6 mu O-cm for Ag) and 2) Cu is approximately 100 times cheaper than Ag, making it an excellent potential replacement. Problems associated with copper (Cu) contacts include 1) easy oxidation and 2) diffusion into the Si cell and recombination activity.
copper paste↗
Development of APCVD BSG and POCl 3 Codiffusion Process for Double-Side TOPCon Solar Cell Precursor Fabrication
This paper presents a commercially viable process for fabricating a high-quality double-side tunnel oxide passivating contact (DS-TOPCon) cell precursor using APCVD-deposited boron silicate glass and ex-situ POCl 3 diffusion in a single high-temperature step, eliminating the need for additional masking and diffusion processes. A two-tier temperature profile was developed, involving a pre-annealing at above 900°C in nitrogen (N2) ambient followed by POCl 3 diffusion at 840°C. We investigated the effect of varying pre-annealing temperatures, ranging from 875°C to 950°C, on the passivation quality and metal-Si contact properties of both n-TOPCon and p-TOPCon layers. The resultant DS-TOPCon cell precursor after silicon nitride (SiNX) passivation exhibited an excellent iV OC of close to 730 mV. In addition, a rapid asymmetric poly-Si thinning technique, developed in this work, enabled adjustment of the front n + poly-Si thickness while maintaining the rear p + poly-Si thickness. Two types of DS-TOPCon cell architectures can be fabricated: i) full-area thin (≈40nm) n-TOPCon layer on the front and ii) selective-area thick (≈200nm) n-TOPCon fingers underneath the metal grid. Device simulations suggest that full-area DS-TOPCon cell with 40 nm n + poly-Si and selective-area DS-TOPCon cell with 200 nm n + poly fingers on the front, fabricated from our current DS-TOPCon cell precursor, can achieve cell efficiencies of 22.1 and 23.5%, respectively. Detailed power loss analysis and device simulation reveal that further improvements in material and device parameters have potential to push the cell efficiencies of DS-TOPCon cell structure beyond 25%, making it a promising alternative to fabricate a high-efficiency next-generation solar cells at low cost.
14 SOLAR ENERGY↗
Development and Reliability of Screen-Printable Fire-Through Cu Paste for Passivated Contact Solar Cells
We present the development of copper (Cu) paste which has been screen printed on Selective Emitter-Passivated Emitter Rear Contact (SE-PERC) solar cells. This paste can also be applied to Tunnel Oxide Passivated Contact (TOPCON) solar cells due to its fire-through nature. Champion PERC cells have achieved ....efficiency with ...parameters . Accelerated testing to investigate reliability performance of the SE- PERC mini-modules were carried out in damp heat chamber with 85oC and 85% humidity. The devices were found to be operational even after 1,500 hours. Devices with screen printed Ag contacts on the front side have been studied in parallel to the Cu contacts for comparison.
copper paste↗
Enhanced passivation and stability of negative charge injected SiN x with higher nitrogen content on the boron diffused surface of n-type Si solar cells
This paper explores the potential of the negatively charged SiN x using plasma charge injection technology to passivate the front textured boron-diffused emitter of n-type Si solar cells. The high-x value single SiN x layer with x ≥ 1.30 (x = N/Si) previously developed for the planarized rear-side passivation of p-type silicon solar cells, with an excellent passivation and charge stability, was found to be unacceptable for the passivation on the front textured boron emitter of n-type cells due to a severe bulk lifetime degradation issue. Therefore, in this study, we investigated a new concept of depositing a dual-x SiN x with a low-x SiN x layer (x~1.01) on top of a high-x SiN x layer (x~1.30) for passivation of the front textured rough surface of boron diffused emitter in n-type cells. Here, the optimized dual-x SiN x stack reveals the promise of charge retention for more than 25 years in field operation as well as excellent passivation of boron-doped emitter without bulk lifetime degradation. N-type cells with the optimized dual-x SiN x after charge injection show comparable cell performance to Al 2 O 3 passivated reference cells. The results of cell-level light stability tests using one-cell minimodules exhibit cell performance decay characteristics similar to the traditional Al 2 O 3 /SiN x passivated reference module.
14 SOLAR ENERGY↗
Coatings Boost Solar-Cell Outputs
Efficiencies increased by more-complete utilization of incident light. Electrical outputs of thin solar photovoltaic cells made of dendritic-web silicon increased by combination of front-surface, antireflective coatings and back-surface, reflective coatings. Improvements achieved recently through theoretical and experimental studies of ways to optimize coatings for particular wavelengths of incident light, cell thicknesses, and cell materials.
Rohatgi, Ajeet↗
Improving Solar Cells With Polycrystalline Silicon
In proposed solar-cell design, layers of polycrystalline silicon grown near front metal grid and back metal surface. Net electrical effect increases open-circuit voltage and short-circuit current, resulting in greater cell power output and energy conversion efficiency. Solar-cell configuration differs from existing one in that layers of doped polycrystalline silicon added to reduce recombination in emitter and back surface field regions.
Rohatgi, Ajeet↗