Engineering Papers⌕ Search

Engineering topics

Rock, Christopher

Publications and source records attributed to Rock, Christopher.

Microstructure development and properties of micro-alloyed copper, Cu-0.3Zr-0.15Ag, produced by electron beam additive manufacturing

A micro-alloyed copper powder, Cu-0.3Zr-0.15Ag wt.%, was produced using gas atomization reaction synthesis. Zirconium was added to copper to sequester the oxygen present as copper oxide surface films on the powder particles. The as-received powders, as well as the intentionally oxidized powders were used to fabricate solid test articles by electron beam powder bed fusion additive manufacturing. Dense samples fabricated from as-received powder demonstrated nominal UTS, yield, and elongation values at 260 MPa, 150 MPa, and 34%, respectively. The average electrical conductivity of these samples was measured at 95% of the international annealed copper standard (IACS). Samples fabricated from the oxidized powder exhibited nominal UTS, yield, and elongation of 241 MPa, 146 MPa, and 43%, respectively, with an electrical conductivity of 95 % IACS. During characterization, it was observed that, rather than forming nano-scale dispersoids, the Zirconia (ZrO 2 ) appeared as discontinuous stringers in the metallographic cross-sections that crossed grain and melt pool boundaries. This was rationalized by tracing the presence of the micro-alloying addition of elemental zirconium, which was found to react with surface oxides dissociated in the melt pool to form ZrO 2 , which then solidified on the surface of the melt pool through an allotropic transformation to monoclinic ZrO 2 in discontinuous films and spheroids ranging in size from nanometers to microns. This was confirmed by microscopic analysis of the tops of the melt pools. On subsequent melt passes, these ZrO 2 structures were displaced and redistributed within the melt pool.

36 MATERIALS SCIENCE↗

Final technical report

A new series of MW-class, RF loads were developed that can dissipate power levels exceeding 1.5 MW at frequencies from 28 GHz to 180 GHz. The new loads are designed to reflect less than 0.25% of the input power and operate continuously (CW). Stainless-steel and anodized aluminum versions were developed. The stainless steel version is designed to meet requirements for nuclear facilities, such as ITER, while the aluminum version is capable of power levels exceeding 2 MW CW. The aluminum version is also lighter and less expensive. This report describes the design activities during the program and the performance characteristics of the loads.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Laser Powder Bed Fusion of ODS 14YWT from Gas Atomization Reaction Synthesis Precursor Powders

Abstract Laser powder bed fusion (LPBF) additive manufacturing (AM) is a promising route for the fabrication of oxide dispersion strengthened (ODS) steels. In this study, 14YWT ferritic steel powders were produced by gas atomization reaction synthesis (GARS). The rapid solidification resulted in the formation of stable, Y-containing intermetallic Y 2 Fe 17 on the interior of the powder and a stable Cr-rich oxide surface. The GARS powders were consolidated with LPBF. Process parameter maps identified a stable process window resulting in a relative density of 99.8%. Transmission electron microscopy and high-energy x-ray diffraction demonstrated that during LPBF, the stable phases in the powder dissociated in the liquid melt pool and reacted to form a high density (1.7 × 10 20 /m 3 ) of homogeneously distributed Ti 2 Y 2 O 7 pyrochlore dispersoids ranging from 17 to 57 nm. The use of GARS powder bypasses the mechanical alloying step typically required to produce ODS feedstock. Preliminary mechanical tests demonstrated an ultimate tensile and yield strength of 474 MPa and 312 MPa, respectively.

36 MATERIALS SCIENCE↗

Electron Beam Melting of Niobium Alloys from Blended Powders

Niobium-based tungsten alloys are desirable for high-temperature structural applications yet are restricted in practice by limited room-temperature ductility and fabricability. Powder bed fusion additive manufacturing is one technology that could be leveraged to process alloys with limited ductility, without the need for pre-alloying. A custom electron beam powder bed fusion machine was used to demonstrate the processability of blended Nb-1Zr, Nb-10W-1Zr-0.1C, and Nb-20W-1Zr-0.1C powders, with resulting solid optical densities of 99+%. Ultimately, post-processing heat treatments were required to increase tungsten diffusion in niobium, as well as to attain satisfactory mechanical properties.

36 MATERIALS SCIENCE↗

Additive Manufacturing of Pure Mo and Mo + TiC MMC Alloy by Electron Beam Powder Bed Fusion

A metal matrix composite powder of molybdenum (Mo) + TiC was produced by mechanical alloying (MA) and used in additive manufacturing by electron beam powder bed fusion along with pure Mo powder to form sandwich structures. The Mo + TiC solid layers formed mixed structures of Mo with discrete TiC particles, eutectic Mo + TiC, and Mo dendrites. Thermodynamic modeling showed that the system contained an invariant eutectic reaction in the composition range used and indicated that the system was highly sensitive to changes in composition and temperature.

36 MATERIALS SCIENCE↗

Processing of Alnico Magnets by Additive Manufacturing

Permanent magnets without rare earth (RE) elements, such as alnico, will improve supply stability and potentially decrease permanent magnet cost, especially for traction drive motors and other increased temperature applications. Commercial alnico magnets with the highest energy product are produced by directional solidification (DS) to achieve a < 001 > columnar grain orientation followed by significant final machining, adding to the high cost. Additive manufacturing (AM) is an effective method to process near net-shape parts with minimal final machining of complex geometries. AM also, has potential for texture/grain orientation control and compositionally graded structures. This report describes fabrication of alnico magnets by AM using both laser engineered net shaping (LENS)/directed energy deposition (DED) and electron beam melting powder bed fusion (EBM/PBF). High pressure gas atomized (HPGA) pre-alloyed alnico powders, with high purity and sphericity, were built into cylindrical and rectangular samples, followed by magnetic annealing (MA) and a full heat treatment (FHT). The magnetic properties of these AM processed specimens were different from their cast and sintered counterparts of the same composition and show a great sensitivity to heat treatment. The AM process parameters used in this developmental study did not yet result in any preferred texture within the alnico AM builds. These findings demonstrate feasibility for near net-shape processing of alnico permanent magnets for use in next generation traction drive motors and other applications requiring increased operating temperatures and/or complex engineered part geometries, especially with further AM process development for texture control.

36 MATERIALS SCIENCE↗

Characteristics and Processing of Hydrogen-Treated Copper Powders for EB-PBF Additive Manufacturing

The fabrication of high purity copper using additive manufacturing has proven difficult because of oxidation of the powder feedstock. Here, we present work on the hydrogen heat treatment of copper powders for electron beam powder bed fusion (EB-PBF), in order to enable the fabrication of high purity copper components for applications such as accelerator components and vacuum electronic devices. Copper powder with varying initial oxygen contents were hydrogen heat-treated and characterized for their chemistry, morphology, and microstructure. Higher initial oxygen content powders were found to not only reduce surface oxides, but also reduce oxides along the grain boundaries and form trapped H 2 O vapor inside the particles. The trapped H 2 O vapor was verified by thermogravimetric analysis (TGA) and residual gas analysis (RGA) while melting. The mechanism of the H 2 O vapor escaping the particles was determined by in-situ SEM heated stage experiments, where the particles were observed to crack along the grain boundaries. To determine the effect of the EB-PBF processing on the H 2 O vapor, the thermal simulation and the validation of single melt track width wafers were conducted along with melting single layer discs for chemistry analysis. A high speed video of the EB-PBF melting was performed in order to determine the effect of the trapped H 2 O vapor on the melt pool. Finally, solid samples were fabricated from hydrogen-treated copper powder, where the final oxygen content measured ~50 wt. ppm, with a minimal residue hydrogen content, indicating the complete removal of trapped H 2 O vapor from the solid parts.

36 MATERIALS SCIENCE↗