Engineering Papers⌕ Search

Engineering topics

Robison, Thomas

Publications and source records attributed to Robison, Thomas.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of Silica and Mixing Time on Microstructures of Porous Polymer Composite by Emulsion Templating

Porous polymer composite with tailored porosity is applied in the myriads of areas such as energy storage, oil/water absorption, bioengineering, and advanced areas of material science. The emulsion templating technology is one of the most popular methods for synthesizing porous polymer composite. It involves solidifying a two-phase mixture of porogen and polymer, then removing porogen to create pores within the continuous emulsion phase by polymerization or curing. The surfactant plays a pivotal role in accomplishing a stable emulsion, a key factor in designing the internal porous structure. This study highlights the effect of silica filler and mixing time on pore morphology, i.e., shape, size, and distribution. on polydimethylsiloxane (PDMS) porous structure utilizing the water-in-oil emulsion templating method. Span® 80 is used as a surfactant to reduce the surface tension between water, silica, and PDMS and simultaneously create a strong foaming effect. Different weight concentrations of silica (1-10 wt%) were chosen while keeping the internal phase, i.e., water (50 wt%) constant. The designed porous structures were further characterized through scanning electron microscopy (SEM). Porous composite specimens fabricated with higher silica content and mixing time consistently exhibit smaller pore sizes than specimens fabricated with lower mixing time and silica content. A breakthrough of pore morphology is seen at silica content higher than 5wt% at 1 min mixing, however, pore morphology drastically changes when mixing time increases from 1 min to 6 min. Variation of finer mixing time beyond 1 min shows stepwise changes in pore morphology from a large single-phase porous structure to a bi-modal porous structure which eventually become a smaller single-mode porous structure. Thus, the emulsion templating technique, in combination with different filler content and mixing time, will effectively aid in designing engineered porous polymer composite with varying stiffness and pore morphology.

Porous polymer, Emulsion templating, Surfactant, P↗
DOE OSTI2022

Low-temperature selective laser sintering 3D printing of PEEK-Nylon blends: Impact of thermal post-processing on mechanical properties and thermal stability

Herein, a high-performance polymer (HPP) (polyether ether ketone, PEEK) blended with a commercial low-temperature polymer (polyamide 12, PA-12) was fabricated using a low-temperature selective laser sintering (SLS) 3D printer. Different post-processing heat treatments were implemented after fabrication to tune the thermal and mechanical properties of printed blends. The specific mechanical modulus of the blend was increased up to 79% in comparison to printed PA-12 samples with heat treatment. Additionally, the thermal resistance of the treated blends greatly exceeded the properties observed using PA-12 alone. This research proposes a methodology to fabricate and engineer HPP using desktop SLS printers through a secondary lower melting temperature material and heat treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Selective Laser Sintering of High-Temperature Thermoset Polymer

Thermoplastic materials such as PA12 and PA6 have been extensively employed in Selective Laser Sintering (SLS) 3D printing applications due to their printability, processability, and crystalline structure. However, thermoplastic-based materials lack polymer inter-chain bonding, resulting in inferior mechanical and thermal properties and relatively low fatigue behavior. Therefore, 3D printing of high-performance crosslinked thermosets using SLS technology is paramount to pursue as an alternative to thermoplastics. In this work, a thermoset resin was successfully 3D printed using SLS, and its thermal stability of printed parts after a multi-step post-curing process was investigated. Dimensionally stable and high glass transition temperature (Tg: ~300 °C) thermoset parts were fabricated using SLS. The polymer crosslinking mechanism during the printing and curing process was investigated through FTIR spectra, while the mechanical stability of the SLS 3D-printed thermoset was characterized through compression tests. It is found that 100% crosslinked thermoset can be 3D printed with 900% higher compressive strength than printed green parts.

Hassan, Md Sahid (ORCID:0000000304665395)↗
DOE OSTI2021

Synthesis and characterization of porous polydimethylsiloxane structures with adjustable porosity and pore morphology using emulsion templating technique

Abstract Porous polydimethylsiloxane (PDMS) framework with adjustable pore structures has been fabricated by polymerization of the continuous phase in the emulsion templates. Different types of surfactants, including nonionic (Triton X‐100), cationic (Benzalkonium chloride), anionic (sodium dodecyl sulfate), and silicone‐based block copolymer were used to stabilize the water‐in‐oil emulsion system. Deionized water with a wide range of internal phases varying from 10% to 60% by weight was employed to make the low internal phase emulsion and medium internal phase emulsion. The effect of surfactant type, surfactant concentration, and the internal phase volume on the stability of the emulsion, pore morphology, and pore size distribution was explored. The stability of the emulsion was investigated by comparing the pore morphology of the cured sample at different set times, such as 0, 6, and 72 h. Scanning electron microscopy was employed for the characterization of the porous structures. The image analysis was conducted, and the pore size distribution, porosity, and open‐cell ratio of each sample were calculated. Interconnected pores have been seen in the porous PDMS made from emulsions with an internal phase larger than 30%. The results demonstrated that the frequency of open‐cell pores and the pore size is dependent on the surfactant types.

Abshirini, Mohammad↗
DOE OSTI2021

Investigation of porous polydimethylsiloxane structures with tunable properties induced by the phase separation technique

This article reports the fabrication and characterization of porous polydimethylsiloxane (PDMS) structures developed by the solvent evaporationinduced phase separation technique. Here, ternary systems containing water/ tetrahydrofuran (THF)/PDMS with various concentrations are produced to form a stable solution. The porous PDMS structures are formed by removing the solvent (THF) and nonsolvent (water) phases during the stepping heat treatment procedure. The analytical ternary phase diagram is constructed based on the thermodynamic equilibrium state in the polymer solution to explain the stable/unstable formulations and the possible composition change path. The results show that the isolated pores with the adjustable pore size ranging from 330 to 1900 μm are obtained by tuning the water to the THF ratio. The mechanical properties of the porous PDMS structures are determined by conducting the tensile tests on the prepared dog bone-shaped specimens. A wide range of elastic modulus ranging between 0.49 and 1.05 MPa was achieved without affecting the density of the porous sample by adjusting the solvent and non-solvent content in the solution. It is shown that the flexibility of the porous structures can be improved by reducing the ratio of water to THF and decreasing the PDMS content. The porosity measurements reveal that the PDMS concentration is the major phase controlling the porosity of the structure, while the effect of water/THF is negligible.

42 ENGINEERING↗
DOE OSTI2020

Easy-Processable and Aging-Free All-Polymer Polysiloxane Composites

In this work, we report all-polymer polysiloxane composites that overcome the long-standing processing problems of silica-reinforced silicone rubbers. Polystyrene fillers are dispersed with styrene/dimethylsiloxane symmetric diblock and triblock copolymers that control the filler morphology, filler–matrix interactions, and filler–filler interactions. Surprisingly, the composites not only rival the traditional silica-reinforced polysiloxane in mechanical properties of cured materials but also have better processability and stability than the silica-filled compound before curing. Large amplitude oscillatory shear experiments demonstrate that the triblock copolymer addition strongly affects the rheological properties. We hypothesize that the bridges and entangled loops that were formed by the triblock copolymer can connect different PS domains to provide additional reinforcement. The aging effect that originates from PDMS chain adsorption on the filler particle surface is also avoided because of the thermodynamic repulsion between PS and PDMS phases.

36 MATERIALS SCIENCE↗