Engineering topics

Robinson, D. N.

Publications and source records attributed to Robinson, D. N..

28 records · Page 2

NASA NTRS1985

Thermomechanical deformation in the presence of metallurgical changes

Nonisothermal testing that can be used as a basis of a nonisothermal representation is discussed. Related tests regarding metallurgical changes that occur in other high temperature structural alloys are discussed. A viscoplastic constitutive model capable of qualitatively representing the behavioral features was formulated. This model is used to assess the differences in ultimate life prediction in some typical nonisothermal structural problems when the constitutive model does or does not account for metallurgically induced thermomechanical history dependence.

Robinson, D. N.↗

NASA NTRS1985

Some advances in experimentation supporting development of viscoplastic constitutive models

The development of a biaxial extensometer capable of measuring axial, torsion, and diametral strains to near-microstrain resolution at elevated temperatures is discussed. An instrument with this capability was needed to provide experimental support to the development of viscoplastic constitutive models. The advantages gained when torsional loading is used to investigate inelastic material response at elevated temperatures are highlighted. The development of the biaxial extensometer was conducted in two stages. The first involved a series of bench calibration experiments performed at room temperature. The second stage involved a series of in-place calibration experiments performed at room temperature. A review of the calibration data indicated that all performance requirements regarding resolution, range, stability, and crosstalk had been met by the subject instrument over the temperature range of interest, 21 C to 651 C. The scope of the in-placed calibration experiments was expanded to investigate the feasibility of generating stress relaxation data under torsional loading.

Ellis, J. R.↗

NASA NTRS1985

On thermomechanical testing in support of constitutive equation development for high temperature alloys

Three major categories of testing are identified that are necessary to provide support for the development of constitutive equations for high temperature alloys. These are exploratory, charactrization and verification tests. Each category is addressed and specific examples of each are given. An extensive, but not exhaustive, set of references is provided concerning pertinent experimental results and their relationships to theoretical development. This guide to formulating a meaningful testing effort in support of consitutive equation development can also aid in defining the necessary testing equipment and instrumentation for the establishment of a deformation and structures testing laboratory.

Robinson, D. N.↗

NASA NTRS1985

Some advances in experimentation supporting development of viscoplastic constitutive models

The development of a biaxial extensometer capable of measuring axial, torsion, and diametral strains to near-microstrain resolution at elevated temperatures is discussed. An instrument with this capability was needed to provide experimental support to the development of viscoplastic constitutive models. The advantages gained when torsional loading is used to investigate inelastic material response at elevated temperatures are highlighted. The development of the biaxial extensometer was conducted in two stages. The first involved a series of bench calibration experiments performed at room temperature. The second stage involved a series of in-place calibration experiments conducted at room and elevated temperature. A review of the calibration data indicated that all performance requirements regarding resolution, range, stability, and crosstalk had been met by the subject instrument over the temperature range of interest, 21 C to 651 C. The scope of the in-place calibration experiments was expanded to investigate the feasibility of generating stress relaxation data under torsional loading.

Ellis, J. R.↗

NASA NTRS1985

Viscoplastic constitutive relationships with dependence on thermomechanical history

Experimental evidence of thermomechanical history dependence in the cyclic hardening behavior of some common high-temperature structural alloys is presented with special emphasis on dynamic metallurgical changes. The inadequacy of formulating nonisothermal constitutive equations solely on the basis of isothermal testing is discussed. A representation of thermoviscoplasticity is proposed that qualitatively accounts for the observed hereditary behavior. This is achieved by formulating the scalar evolutionary equation in an established viscoplasticity theory to reflect thermomechanical path dependence. To assess the importance of accounting for thermomechanical history dependence in practical structural analyses, two qualitative models are specified: (1) formulated as if based entirely on isothermal information; (2) to reflect thermomechanical path dependence using the proposed thermoviscoplastic representation. Predictions of the two models are compared and the impact the calculated differences in deformation behavior may have on subsequent lifetime predictions is discussed.

Robinson, D. N.↗

NASA NTRS1984

High-temperature constitutive modeling

Thermomechanical service conditions for high-temperature levels, thermal transients, and mechanical loads severe enough to cause measurable inelastic deformation are studied. Structural analysis in support of the design of high-temperature components depends strongly on accurate mathematical representations of the nonlinear, hereditary, inelastic behavior of structural alloys at high temperature, particularly in the relatively small strain range. Progress is discussed in the following areas: multiaxial experimentation to provide a basis for high-temperature multiaxial constitutive relationships; nonisothermal testing and theoretical development toward a complete thermomechanically path dependent formulation of viscoplasticity; and development of viscoplastic constitutive model accounting for initial anisotropy.

Robinson, D. N.↗

NASA NTRS1983

Constitutive Equations for Use in Design Analyses of Long-life Elevated Temperature Components

Design analysis needs and procedures relative to elevated temperature components in liquid metal fast breeder reactor (LMFBR) system were examined. The effects of the thermal transients on the pressure boundary components are enhanced by the excellent heat transfer properties of the liquid sodium coolant. Design criteria for high temperature nuclear reactor components recognize the potential occurrence of inelastic structural response. Specifically, criteria and limits were developed which reflect a recognition of this potential and employ design by analysis concepts that requires that inelastic (elastic-plastic and creep) analyses be performed. Constitutive equations to represent multiaxial time-dependent responses of LMFBR alloys are established. The development of equations applicable under cyclic loading conditions are outlined.

Pugh, C. E.↗

NASA NTRS1983

A Unified Constitutive Relationship for the Time-dependent Behavior of Fast Breeder Alloys

Constitutive equations based on classical concepts of creep and plasticity generally rest on the assumption that the inelastic strain can be decomposed into two distinct and additive contributions, one time dependent (creep) and the other time dependent (plastic). It is suggested that an approach is to adopt a unified representation in which creep and plasticity are characterized as occurring simultaneously and interactively and time is an essential ingredient throughout. Examples of the inherent time dependency exhibited by some fast breeder alloys at elevated temperature are rate dependency under monotonic and cyclic straining, thermal recovery and strong creep-elasticity interaction. The stron influence of the recent history of plastic straining on stress relaxation is shown.

Robinson, D. N.↗

NASA NTRS1983

Constitutive relationships for anisotropic high-temperature alloys

A constitutive theory is presented for representing the anisotropic viscoplastic behavior of high-temperature alloys that possess directional properties resulting from controlled grain growth or solidification. The theory is an extension of a viscoplastic model that has been applied in structural analyses involving isotropic metals. Anisotropy is introduced through the definition of a vector field that identifies a preferential (solidification) direction at each material point. Following the development of a full multiaxial theory, application is made to homogeneously stressed elements in pure shear and to a uniaxially stressed rectangular block in plane stress with the stress direction oriented at an arbitrary angle with the material direction. It is shown that an additional material parameter introduced to characterize the degree of anisotropy can be determined on the basis of simple creep tests.

Robinson, D. N.↗

NASA NTRS1982

Constitutive relationships for anisotropic high-temperature alloys

A constitutive theory is presented for representing the anisotropic viscoplastic behavior of high temperature alloys that posses directional properties resulting from controlled grain growth or solidification. The theory is an extension of a viscoplastic model that was applied in structural analyses involving isotropic metals. Anisotropy is introduced through the definition of a vector field that identifies a preferential (solidification) direction at each material point. Following the development of a full multiaxial theory, application is made to homogeneously stressed elements in pure shear and to a uniaxially stressed rectangular block in plane stress with the stress direction oriented at an arbitrary angle with the material direction. It is shown that an additional material parameter introduced to characterize the degree of anisotropy can be determined on the basis of simple creep tests.

Robinson, D. N.↗